Doubly Fed Induction Generators : Overview and Intelligent Control Strategies for Wind Energy Conversion Systems

Adjustable speed induction generators, especially the Doubly-Fed Induction Generators (DFIG) are becoming increasingly popular due to its various advantages over fixed speed generator systems. A DFIG in a wind turbine has ability to generate maximum power with varying rotational speed, ability to control active and reactive by integration of electronic power converters such as the back-to-back converter, low rotor power rating resulting in low cost converter components, etc, DFIG have become very popular in large wind power conversion systems. This chapter presents an extensive literature survey over the past 25 years on the different aspects of DFIG. Application of H8 Controller for enhanced DFIG-WT performance in terms of robust stability and reference tracking to reduce mechanical stress and vibrations is also demonstrated in the chapter.

Application of TS-Fuzzy Controller for Active Power and DC Capacitor Voltage Control in DFIG-Based Wind Energy Conversion Systems

This chapter focuses on the implementation of the TS (Tagaki-Sugino) fuzzy controller for the Doubly Fed Induction Generator (DFIG) based wind generator. The conventional PI control loops for mantaining desired active power and DC capacitor voltage is compared with the TS fuzzy controllers. DFIG system is represented by a third-order model where electromagnetic transients of the stator are neglected. The effectiveness of the TS-fuzzy controller on the rotor speed oscillations and the DC capacitor voltage variations of the DFIG damping controller on converter ratings is also investigated. The results from the time domain simulations are presented to elucidate the effectiveness of the TS-fuzzy controller over the conventional PI controller in the DFIG system. The proposed TS-fuzzy con-troller can improve the fault ride through capability of DFIG compared to the conventional PI controller.

Secular and religious moral grounds resonating across state schools in Indonesia

This paper describes moral education in Indonesia, more particularly, how teachers have implemented the Character Education policy issued by the Ministry of Education and Culture (MOEC) in 2010. This policy required teachers to instil certain values in every lesson, including EFL lessons, to contribute towards building a shared national moral character. Drawing on Durkheim's distinction between secular and religious morality, this paper considers how state schools accommodated and promoted this ‘rational moral education' or secular morality (Durkheim, 1925) in government schools, and how it interacted with religious moral education. This paper uses Bernstein's concepts of pedagogic discourse, instructional and regulative discourses to analyse how teachers have recontextualised this policy in the micro pedagogic settings of their EFL classes. Three types of data were collected for this study: interviews, class observations and teachers' lesson plans. In this way, four EFL teachers working in state schools were interviewed on two occasions and three of their classes were observed. The first interview identified teachers' beliefs and perceptions regarding the Character Education policy. Their classroom and lesson plans were observed to augment this information. Then the final interview asked about the teacher's thinking behind their actions in the observed classes. Since character education was issued within the broader frame of school based curriculum that offered schools and teachers more choices to develop the local curriculum and its intent, the analysis will focus on what moral premises were evident in their school and classes, and how such morality was transmitted through the EFL lessons. The conclusion suggests that teachers' implementation of moral education in their classes was dominated by their school communities and the teachers' own preferred value of religiosity. Such value played out in the classes through both the regulative discourse and the instructional discourse.

Basic Religious Charities

Just over 44,000 registered charities filed their first Annual Information Statement (AIS) return with the Australian Charities and Not-for-profits Commission (ACNC) before the end of October 2014. Of these, 10,918 charities self-identified as Basic Religious Charities (BRCs). These are usually, but not always, unincorporated religious congregations which receive no or little government funding. Having a central agency for reporting, in the form of the ACNC, having access to information supplied in the AIS by registered organisations has allowed access to new measures of charities and their activities. In September 2014 the ACNC, in conjunction with Curtin University Not-for-profit Initiative, released a high-level report on the first AIS, and the data were also made available digitally through the Australian Government Data Repository. This factsheet builds on that report by focusing on BRCs.

Pentacene on Ni(111): room-temperature molecular packing and temperature-activated conversion to graphene

We investigate, using scanning tunnelling microscopy, the adsorption of pentacene on Ni(111) at room temperature and the behaviour of these monolayer films with annealing up to 700 °C. We observe the conversion of pentacene into graphene, which begins from as low as 220 °C with the coalescence of pentacene molecules into large planar aggregates. Then, by annealing at 350 °C for 20 minutes, these aggregates expand into irregular domains of graphene tens of nanometers in size. On surfaces where graphene and nickel carbide coexist, pentacene shows preferential adsorption on the nickel carbide phase. The same pentacene to graphene transformation was also achieved on Cu(111), but at a higher activation temperature, producing large graphene domains that exhibit a range of moiré superlattice periodicities.

Real time maximum power conversion tracking and resonant frequency modification for high power piezoelectric ultrasound transducer

Piezoelectric ultrasound transducers are commonly used to convert mechanical energy to electrical energy and vice versa. The transducer performance is highly affected by the frequency at which it is excited. If excitation frequency and main resonant frequency match, transducers can deliver maximum power. However, the problem is that main resonant frequency changes in real time operation resulting in low power conversion. To achieve the maximum possible power conversion, the transducer should be excited at its resonant frequency estimated in real time. This paper proposes a method to first estimate the resonant frequency of the transducer and then tunes the excitation frequency accordingly in real time. The measurement showed a significant difference between the offline and real time resonant frequencies. Also, it was shown that the maximum power was achieved at the resonant frequency estimated in real time compare to the one measured offline.

Conversion of n-type CuTCNQ into p-type nitrogen-doped CuO and the implication for room temperature gas sensing

Sensors to detect toxic and harmful gases are usually based on metal oxides that are operated at elevated temperature. However, enabling gas detection at room temperature (RT) is a significant ongoing challenge. Here, we address this issue by demonstrating that microrods of semiconducting CuTCNQ (TCNQ=7,7,8,8-tetracyanoquinodimethane) with nanostructured features can be employed as conductometric gas sensors operating at 50°C for detection of oxidizing and reducing gases such as NO2 and NH3. The sensor is evaluated at RT and up to 200°C. It was found that CuTCNQ is transformed into a N-doped CuO material with p-type conductivity when annealed at the maximum temperature. This is the first time that such a transformation, from a semiconducting charge transfer material into a N-doped metal oxide is detected. It is shown here that both the surface chemistry and the type of majority charge carrier within the sensing layer is critically important for the type of response towards oxidizing and reducing gases. A detailed physical description of NO2 and NH3 sensing mechanism at CuTCNQ and N-doped CuO is provided to explain the difference in the response. For the N-doped CuO sensor, a detection limit of 1 ppm for NO2 and 10 ppm for NH3 are achieved.

Reversible Conversion of Dominant Polarity in Ambipolar Polymer/Graphene Oxide Hybrids

The possibility to selectively modulate the charge carrier transport in semiconducting materials is extremely challenging for the development of high performance and low-power consuming logic circuits. Systematical control over the polarity (electrons and holes) in transistor based on solution processed layer by layer polymer/graphene oxide hybrid system has been demonstrated. The conversion degree of the polarity is well controlled and reversible by trapping the opposite carriers. Basically, an electron device is switched to be a hole only device or vice versa. Finally, a hybrid layer ambipolar inverter is demonstrated in which almost no leakage of opposite carrier is found. This hybrid material has wide range of applications in planar p-n junctions and logic circuits for high-throughput manufacturing of printed electronic circuits.

Direct photocatalytic conversion of aldehydes to esters using supported gold nanoparticles under visible light irradiation at room temperature

Visible light can drive esteri fi cation from aldehydes and alcohols using supported gold nanoparticles (Au/Al 2 O 3 ) as photo- catalysts at ambient temperatures. The gold nanoparticles (AuNPs) absorb visible light due to the localized surface plasmon resonance (LSPR) e ff ect, and the conduction electrons of the AuNPs gain the energy of the incident light. The energetic electrons, which concentrate at the NP surface, facilitate the activation of a range of aldehyde and alcohol substrates. The photocatalytic e ffi ciencies strongly depend on the Au loading, particle sizes of the AuNPs, irradiance, and wavelength of the light irradiation. Finally, a plausible reaction mechanism was proposed, and the Au/Al 2 O 3 catalysts can be reused several times without signi fi cantly losing activity. The knowledge acquired in this study may inspire further studies in new e ffi cient recyclable photocatalysts and a wide range of organic synthesis driven by sunlight.

The dependence of computed tomography number to relative electron density conversion on phantom geometry and its impact on planned dose

A computed tomography number to relative electron density (CT-RED) calibration is performed when commissioning a radiotherapy CT scanner by imaging a calibration phantom with inserts of specified RED and recording the CT number displayed. In this work, CT-RED calibrations were generated using several commercially available phantoms to observe the effect of phantom geometry on conversion to electron density and, ultimately, the dose calculation in a treatment planning system. Using an anthropomorphic phantom as a gold standard, the CT number of a material was found to depend strongly on the amount and type of scattering material surrounding the volume of interest, with the largest variation observed for the highest density material tested, cortical bone. Cortical bone gave a maximum CT number difference of 1,110 when a cylindrical insert of diameter 28 mm scanned free in air was compared to that in the form of a 30 × 30 cm2 slab. The effect of using each CT-RED calibration on planned dose to a patient was quantified using a commercially available treatment planning system. When all calibrations were compared to the anthropomorphic calibration, the largest percentage dose difference was 4.2 % which occurred when the CT-RED calibration curve was acquired with heterogeneity inserts removed from the phantom and scanned free in air. The maximum dose difference observed between two dedicated CT-RED phantoms was ±2.1 %. A phantom that is to be used for CT-RED calibrations must have sufficient water equivalent scattering material surrounding the heterogeneous objects that are to be used for calibration.

Diabetes in South Asians

Economic, dietary and other lifestyle transitions have been occurring rapidly in most South Asian countries, making their populations more vulnerable to developing Type 2 diabetes and cardiovascular diseases. Recent data show an increasing prevalence of Type 2 diabetes in urban areas as well as in semi-urban and rural areas, inclusive of people belonging to middle and low socio-economic strata. Prime determinants for Type 2 diabetes in South Asians include physical inactivity, imbalanced diets, abdominal obesity, excess hepatic fat and, possibly, adverse perinatal and early life nutrition and intra-country migration. It is reported that Type 2 diabetes affects South Asians a decade earlier and some complications, for example nephropathy, are more prevalent and progressive than in other races. Further, prevalence of pre-diabetes is high, and so is conversion to diabetes, while more than 50% of those who are affected remain undiagnosed. Attitudes, cultural differences and religious and social beliefs pose barriers in effective prevention and management of Type 2 diabetes in South Asians. Inadequate resources, insufficient healthcare budgets, lack of medical reimbursement and socio-economic factors contribute to the cost of diabetes management. The challenge is to develop new translational strategies, which are pragmatic, cost-effective and scalable and can be adopted by the South Asian countries with limited resources. The key areas that need focus are: generation of awareness, prioritizing health care for vulnerable subgroups (children, women, pregnant women and the underprivileged), screening of high-risk groups, maximum coverage of the population with essential medicines, and strengthening primary care. An effective national diabetes control programme in each South Asian country should be formulated, with these issues in mind.

Materials and technologies for energy conversion, saving and storage: A global network enabling capacity-building for sustainable energy in developing countries

Access to energy is a fundamental component of poverty abatement. People who live in homes without electricity are often dependent on dirty, time-consuming and disproportionately expensive solid fuel sources for heating and cooking. [1] In developing countries, the Human Development Index (HDI), which comprises measures of standard of living, longevity and educational attainment, increases rapidly with per capita electricity use. [2] For these reasons the United Nations has been making a concerted effort to promote global access to energy, first by naming 2012 the Year of Sustainable Energy for All, [3] and now by declaring 2014-2024 the Decade of Sustainable Energy for All. [4]

A do-it-yourself (DIY) switched mode power conversion laboratory

In the education of physical sciences, the role of the laboratory cannot be overemphasised. It is the laboratory exercises which enable the student to assimilate the theoretical basis, verify the same through bench-top experiments, and internalize the subject discipline to acquire mastery of the same. However the resources essential to put together such an environment is substantial. As a result, the students go through a curriculum which is wanting in this respect. This paper presents a low cost alternative to impart such an experience to the student aimed at the subject of switched mode power conversion. The resources are based on an open source circuit simulator (Sequel) developed at IIT Mumbai, and inexpensive construction kits developed at IISc Bangalore. The Sequel programme developed by IIT Mumbai, is a circuit simulation program under linux operating system distributed free of charge. The construction kits developed at IISc Bangalore, is fully documented for anyone to assemble these circuit which minimal equipment such as soldering iron, multimeter, power supply etc. This paper puts together a simple forward dc to dc converter as a vehicle to introduce the programming under sequel to evaluate the transient performance and small signal dynamic model of the same. Bench tests on the assembled construction kit may be done by the student for study of operation, transient performance and closed loop stability margins etc.

Ufologia ja ufokokemukset uskonnollisina ilmiönä : Teoreettinen tutkimus

The main question of my doctoral thesis is whether ufology and UFO experiences are or can be explained as religious phenomena. My research is theoretical in the sense that I combine and systematise cultural scientific knowledge concerning the religiosity of ufology and UFO experiences and complete this theoretical effort with empirical subject matter. The research material for my study consists of theoretical literature and empirical texts written by ufologists and those who have had UFO experiences. I defined the material in a way that it became full and extensive with regard to ufology, stories about UFO experiences and the cultural scientific literature concerning them. In addition, I present a source criticism for the literature because it is in part informal. The method is analysing and synthesising the material in the context of spiral of hermeneutic inferential process. Definitions of religion, ufology and UFO experience, developed by myself, serve as guide lines for the process. The conclusions of my research are as follows. For the most part, ufology and UFO experiences belong to the category of religion and only a fraction of these instances can be explained as something else, for example psychiatric phenomena. From the religious viewpoint I explain ufology and UFO experiences on four different but interlinked levels: historical, comparative, sociological and psychological. Historically ufology and UFO experiences include esoteristic, Christian and folk religious elements. In addition UFO experiences have significant similarities with folk religious stories and shamanistic experiences. From the perspective of the sociology, of religion ufology and UFO experiences can be analysed as products of our scientific and technological Western culture. Social crisis and social psychological group mechanisms affect the appearance of ufological ideas and UFO experiences. Psychologically, in the background of religious UFO experiences there can be found several factors, such as wishful thinking. Concerning UFO sightings these are misinterpretations of certain ordinary and some rare or exotic natural and technical phenomena. Intense UFO experiences, such as UFO abductions, are stimulated for the most part by hallucinations, sleep paralysis disorders, lively fantasies (in case of fantasy prone personalities) and false memories. In group cases social pressure, small group delusion and the guilt of exposing the true nature of a story come into play. A UFO experience can be traumatising because of certain inferential mechanisms and cognitive dissonance involved in the process of conversion as a UFO experiencer. UFO religiosity is a cross cultural, widespread and a significant field of phenomena, which can offer insight about religious developments in the future. However, UFO religiosity has not been studied extensively. This research is one effort to address this lack of documentation. The motivation behind my thesis was to make ufology and UFO experiences more understandable.

Enzymic Conversion of Agmatine to Putrescine inL athyrms satiuus seedlings - Purification and properties of a multifunctional enzyme (putrescine synthase)

The participation of a multifunctional enzy(am sein - gle polypeptide with multiple catalytic activities (14)) has been demonstrated in the conversion of agmatine to putrescine in Lathyrus sativus seedlings. This enzyme (putrescine synthase) with inherent activities of agmatine iminohydrolase, putrescine transcarbamylase, ornithine transcarbamylase, and carbamate has been purified to homogeneity anhda s M, = 55,000.