Remediation of feedlot effluents using aquatic plants

Feedlots have increased in several regions of Argentina, particularly in the Pampas. The absence of adequate treatments of the effluents produced in these establishments creates serious problems to the society. Phytoremediation can be defined as inexpensive and environmentally sustainable strategy used to remove pollutants by plants. The aim of this study was to evaluate the remediation potential of two macrophyte species (Eichhornia crassipes and Hydrocotyle ranunculoides) on a feedlot effluent. This effluent was treated with these species for 31 days. Control and macrophyte treatments decreased dissolved inorganic nitrogen (DIN), Kjeldahl nitrogen (Kj N), biological oxygen demand (BOD), chemical oxygen demand (COD), total dissolved salts (TDS), total phosphorus (TP), Pb, Zn and Cr levels. At macrophyte treatments, relatively constant pH levels were kept and decreased EC and TDS values were obtained compared to control, mitigating the release of contaminants and potential greenhouse gases to the atmosphere. Moreover, significant increases in biomass were obtained, being higher in E. crassipes. The results allow concluding that the presence of aquatic plants increases the removal rates of nutrients, organic matter and heavy metals from wastewater in approximately 10-17 days for a feedlot effluent with high organic load.

Procesos de depuración de los efluentes líquidos de actividades petrolíferas

La Tesis Doctoral surge debida de los problemas de contaminación ambientales que presentan los efluentes líquidos refinería del petróleo y las industrias de extracción del petróleo crudo en la zona costera de Angola principalmente en las provincias de Cabinda, Zaire y Luanda, en las cuales sus vertidos destruyen la flora y fauna acuática. El objetivo de este trabajo consiste en implementar nuevas técnicas de los procesos de oxidación avanzada para el tratamiento de los efluentes líquidos de refinerías de petróleo, que permitan conseguir una calidad adecuada de los vertidos. Este sector se considera como una fuente de contaminación del medio ambiente, que requiere un control estricto y un tratamiento adecuado para la eliminación de los contaminantes existente en este tipo de agua y posteriormente poder reutilizar estas aguas tratadas para otros fines industriales o verter a los cauces receptores que al menos no perjudique a los ecosistemas. En esta tesis se ha investigado las técnicas más modernas de los procesos de oxidación avanzada para el tratamiento de agua residual de refinería de petróleo, así como: 1) ozonización, 2) peróxido de hidrógeno con ozono, y 3) ultravioleta con ozono. Los resultados obtenidos en este trabajo muestran que el proceso de ozonización simple, ha dado mejores resultados para el tratamiento de este tipo agua residual de petróleo, tanto, en la eliminación de materia orgánica y los fenoles presentes en el agua residual. En la primera fase, con 1 litro de muestra, se alcanzó un rendimiento del 80% en la eliminación de la DQO utilizando 5,97 mg/l de dosis de ozono, con 11 minutos de tiempo de contacto. Respecto a los fenoles se alcanzó una eliminación del 100 % con la misma dosis de ozono y con 11 minutos de tiempo de contacto. En la segunda fase, con 4 litros de muestra, se alcanzó un rendimiento del 66% de la DQO utilizando 22,21 mg/l de dosis de ozono, con 15 minutos de tiempo de contacto y el rendimiento en la eliminación de los fenoles fue de 90 % a las mismas condiciones. The doctoral thesis arises because of environmental pollution problems posed by liquid effluents and oil refinery industries extraction of crude oil in the coastal area of Angola mainly in the provinces of Cabinda, Zaire and Luanda, in which their discharges destroy aquatic flora and fauna. The objective of this work is to implement new techniques of advanced oxidation processes for the treatment of liquid effluents of oil refineries that will achieve an adequate quality of discharges. This sector is considered as a source of environmental pollution, which requires close monitoring and appropriate treatment for the removal of existing contaminants in this water and then treated to reuse this water for other industrial purposes or discharging into streams receptors that at least does not harm ecosystems. In this thesis we investigate the most modern techniques of advanced oxidation processes for treatment of wastewater from oil refinery and: 1) ozonation, 2) hydrogen peroxide, ozone, and 3) radiation with ozone. The results obtained in this study show that the ozonation process simple, has yielded better results for treating wastewater of this type of oil, so the removal of phenols and organic matter present in the wastewater. In the first phase, with 1 liter of sample was reached in 80% yield COD removal using 5.97 mg/l ozone dosage, with 11 minutes of contact time. Regarding phenols elimination was achieved of 100% with the same dose of ozone and 11 minutes contact time In the second phase, with sample 4 liters was reached in 66% yield using 22.21 COD mg / l ozone dosage, with 15 minutes of contact time and the performance in the removal of phenols was of 90% at the same conditions.

Thermogravimetric monitoring of oil refinery sludge

The present work has two dimensions: analytical and environmental. On the one hand we proved that thermogravimetric analysis can be used to perform fast characterization of oil refinery sludge. To this end, thermogravimetric curves were deconvoluted by using autocatalytic kinetics to take into account acceleratory phases in a thermal degradation performed in oxygen-containing atmosphere or at high heating rates. Based on thermogravimetric results, oil refinery sludge was modeled in terms of various fractions (pseudo-components) which degrade as major oil cuts. On the other hand, as an alternative to landfill, we have seen that Soxhlet extraction allows recovery almost half of the weight of sludge as a mixture of hydrocarbons, similar to gas–oil, which burns without residue. This ensures both, waste inerting and significant reduction in sludge volume.

Refinery Nonconventional Feedstocks: Influence of the Coprocessing of Vacuum Gas Oil and Low Density Polyethylene in Fluid Catalytic Cracking Unit on Full Range Gasoline Composition

Gasoline coming from refinery fluid catalytic cracking (FCC) unit is a major contributor to the total commercial grade gasoline pool. The contents of the FCC gasoline are primarily paraffins, naphthenes, olefins, aromatics, and undesirables such as sulfur and sulfur containing compounds in low quantities. The proportions of these components in the FCC gasoline invariable determine its quality as well as the performance of the associated downstream units. The increasing demand for cleaner and lighter fuels significantly influences the need not only for novel processing technologies but also for alternative refinery and petrochemical feedstocks. Current and future clean gasoline requirements include increased isoparaffins contents, reduced olefin contents, reduced aromatics, reduced benzene, and reduced sulfur contents. The present study is aimed at investigating the effect of processing an unconventional refinery feedstock, composed of blend of vacuum gas oil (VGO) and low density polyethylene (LDPE) on FCC full range gasoline yields and compositional spectrum including its paraffins, isoparaffins, olefins, napthenes, and aromatics contents distribution within a range of operating variables of temperature (500–700 °C) and catalyst-feed oil ratio (CFR 5–10) using spent equilibrium FCC Y-zeolite based catalyst in a FCC pilot plant operated at the University of Alicante’s Research Institute of Chemical Process Engineering (RICPE). The coprocessing of the oil-polymer blend led to the production of gasoline with very similar yields and compositions as those obtained from the base oil, albeit, in some cases, the contribution of the feed polymer content as well as the processing variables on the gasoline compositional spectrum were appreciated. Carbon content analysis showed a higher fraction of the C9–C12 compounds at all catalyst rates employed and for both feedstocks. The gasoline’s paraffinicity, olefinicity, and degrees of branching of the paraffins and olefins were also affected in various degrees by the scale of operating severity. In the majority of the cases, the gasoline aromatics tended toward the decrease as the reactor temperature was increased. While the paraffins and iso-paraffins gasoline contents were relatively stable at around 5 % wt, the olefin contents on the other hand generally increased with increase in the FCC reactor temperature.

Gas production during the pyrolysis and gasification of biological and physico-chemical sludges from oil refinery

Pyrolysis and gasification of two different sludges coming from a Spanish refinery have been performed at different experimental conditions. A physico-chemical (PC) and a biological (BIO) sludge have been studied. Runs at different heating rates (approx. 4 and 10 K/s) and with different contact time between gases and decomposed sludge have been performed. In general, the ratio H2/CO is higher in pyrolytic runs. The highest ratio is obtained in the pyrolysis at low heating rate and parallel flow, using both sludges. The maximum emission of CO, i.e. the worst combustion conditions, is given in the runs where contact time is minimized and at high heating rates.