Polarimetric X-band weather radar measurements in the tropics: radome and rain attenuation correction

A polarimetric X-band radar has been deployed during one month (April 2011) for a field campaign in Fortaleza, Brazil, together with three additional laser disdrometers. The disdrometers are capable of measuring the raindrop size distributions (DSDs), hence making it possible to forward-model theoretical polarimetric X-band radar observables at the point where the instruments are located. This setup allows to thoroughly test the accuracy of the X-band radar measurements as well as the algorithms that are used to correct the radar data for radome and rain attenuation. For the campaign in Fortaleza it was found that radome attenuation dominantly affects the measurements. With an algorithm that is based on the self-consistency of the polarimetric observables, the radome induced reflectivity offset was estimated. Offset corrected measurements were then further corrected for rain attenuation with two different schemes. The performance of the post-processing steps was analyzed by comparing the data with disdrometer-inferred polarimetric variables that were measured at a distance of 20 km from the radar. Radome attenuation reached values up to 14 dB which was found to be consistent with an empirical radome attenuation vs. rain intensity relation that was previously developed for the same radar type. In contrast to previous work, our results suggest that radome attenuation should be estimated individually for every view direction of the radar in order to obtain homogenous reflectivity fields.

Design of alternative energy storage systems for hybrid vehicles based on statistical processing of driving cycles information

Hybrid vehicles represent the future for automakers, since they allow to improve the fuel economy and to reduce the pollutant emissions. A key component of the hybrid powertrain is the Energy Storage System, that determines the ability of the vehicle to store and reuse energy. Though electrified Energy Storage Systems (ESS), based on batteries and ultracapacitors, are a proven technology, Alternative Energy Storage Systems (AESS), based on mechanical, hydraulic and pneumatic devices, are gaining interest because they give the possibility of realizing low-cost mild-hybrid vehicles. Currently, most literature of design methodologies focuses on electric ESS, which are not suitable for AESS design. In this contest, The Ohio State University has developed an Alternative Energy Storage System design methodology. This work focuses on the development of driving cycle analysis methodology that is a key component of Alternative Energy Storage System design procedure. The proposed methodology is based on a statistical approach to analyzing driving schedules that represent the vehicle typical use. Driving data are broken up into power events sequence, namely traction and braking events, and for each of them, energy-related and dynamic metrics are calculated. By means of a clustering process and statistical synthesis methods, statistically-relevant metrics are determined. These metrics define cycle representative braking events. By using these events as inputs for the Alternative Energy Storage System design methodology, different system designs are obtained. Each of them is characterized by attributes, namely system volume and weight. In the last part the work, the designs are evaluated in simulation by introducing and calculating a metric related to the energy conversion efficiency. Finally, the designs are compared accounting for attributes and efficiency values. In order to automate the driving data extraction and synthesis process, a specific script Matlab based has been developed. Results show that the driving cycle analysis methodology, based on the statistical approach, allows to extract and synthesize cycle representative data. The designs based on cycle statistically-relevant metrics are properly sized and have satisfying efficiency values with respect to the expectations. An exception is the design based on the cycle worst-case scenario, corresponding to same approach adopted by the conventional electric ESS design methodologies. In this case, a heavy system with poor efficiency is produced. The proposed new methodology seems to be a valid and consistent support for Alternative Energy Storage System design.

UWB radar sensor networks: Detection algorithms design and experimental analysis

In the last years radar sensor networks for localization and tracking in indoor environment have generated more and more interest, especially for anti-intrusion security systems. These networks often use Ultra Wide Band (UWB) technology, which consists in sending very short (few nanoseconds) impulse signals. This approach guarantees high resolution and accuracy and also other advantages such as low price, low power consumption and narrow-band interference (jamming) robustness. In this thesis the overall data processing (done in MATLAB environment) is discussed, starting from experimental measures from sensor devices, ending with the 2D visualization of targets movements over time and focusing mainly on detection and localization algorithms. Moreover, two different scenarios and both single and multiple target tracking are analyzed.

14 ground-penetrating radar lines of Area 5 - Periglacial outwash plain from Potter Cove, King George Island, Antarctic Peninsula

During a field campaign in the Austral spring 2012 the sedimentary architecture of a periglacial flood plain at the northeastern coast of Potter Peninsula (Area 5) was revealed using ground-penetrating radar (GPR, Geophysical Survey Systems, Inc. SIR-3000). 14 profiles were collected using a mono-static 200 MHz antenna operated in common offset mode. Trace increment was set to 0.05 m. A differential global-positioning system (dGPS, Leica GS09) was used to obtain topographical information along the GPR lines. GPR data are provided in RADAN-Format, dGPS coordinates are provided in ascii format; projection is UTM (WGS 84, zone 21S).

31 ground-penetrating radar lines of Area 3 - Beach ridge plain (high wave energy) from Maxwell Bay, King George Island, Antarctic Peninsula

During a field campaign in the Austral spring 2012 the sedimentary architecture of a polar gravel-beach system at the southern coast of Potter Peninsula (Area 3) was revealed using ground-penetrating radar (GPR, Geophysical Survey Systems, Inc. SIR-3000). 31 profiles were collected using a mono-static 200 MHz antenna operated in common offset mode. Trace increment was set to 0.05 m. A differential global-positioning system (dGPS, Leica GS09) was used to obtain topographical information along the GPR lines. GPR data are provided in RADAN-Format, dGPS coordinates are provided in ascii format; projection is UTM (WGS 84, zone 21S).

Radar profiles from South Shetland Islands/Western Antarctic Peninsula

The sedimentary architecture of polar gravel-beach ridges is presented and it is shown that ridge internal geometries reflect past wave-climate conditions. Ground-penetrating radar (GPR) data obtained along the coasts of Potter Peninsula (King George Island) show that beach ridges unconformably overlie the prograding strand plain. Development of individual ridges is seen to result from multiple storms in periods of increased storm-wave impact on the coast. Strand-plain progradation, by contrast, is the result of swash sedimentation at the beach-face under persistent calm conditions. The sedimentary architecture of beach ridges in sheltered parts of the coast is characterized by seaward-dipping prograding beds, being the result of swash deposition under stormy conditions, or aggrading beds formed by wave overtopping. By contrast, ridges exposed to high-energy waves are composed of seaward- as well as landward-dipping strata, bundled by numerous erosional unconformities. These erosional unconformities are the result of sediment starvation or partial reworking of ridge material during exceptional strong storms. The number of individual ridges which are preserved from a given time interval varies along the coast depending on the morphodynamic setting: sheltered coasts are characterized by numerous small ridges, whereas fewer but larger ridges develop on exposed beaches. The frequency of ridge building ranges from decades in the low-energy settings up to 1600 years under high-energy conditions. Beach ridges in the study area cluster at 9.5, 7.5, 5.5, and below 3.5 m above the present-day storm beach. Based on radiocarbon data, this is interpreted to reflect distinct periods of increased storminess and/or shortened annual sea-ice coverage in the area of the South Shetland Islands for the times around 4.3, c. 3.1, 1.9 ka cal BP, and after 0.65 ka cal BP. Ages further indicate that even ridges at higher elevations can be subject to later reactivation and reworking. A careful investigation of the stratigraphic architecture is therefore essential prior to sampling for dating purposes.

47 ground-penetrating radar lines of Area 4 - Gravel spit system from Potter Cove, King George Island, Antarctic Peninsula

During two field campaigns (Austral springs 2011 and 2012) the sedimentary architecture of a polar gravel-spit system at the northern coast of Potter Peninsula (Area 4) was revealed using ground-penetrating radar (GPR, Geophysical Survey Systems, Inc. SIR-3000). 47 profiles were collected using a mono-static 200 MHz antenna operated in common offset mode. Trace increment was set to 0.05 m. A differential global-positioning system (dGPS, Leica GS09) was used to obtain topographical information along the GPR lines. GPR data are provided in RADAN-Format, dGPS coordinates are provided in ascii format; projection is UTM (WGS 84, zone 21S).

21 ground-penetrating radar lines of Area 1 - Beach ridge plain (low wave energy) from Potter Cove, King George Island, Antarctic Peninsula

During two field campaigns (Austral springs 2011 and 2012) the sedimentary architecture of a polar gravel-beach system at the western coast of Potter Peninsula (Area 1) was revealed using ground-penetrating radar (GPR, Geophysical Survey Systems, Inc. SIR-3000). 21 profiles were collected using a mono-static 200 MHz antenna operated in common offset mode. Trace increment was set to 0.05 m. A differential global-positioning system (dGPS, Leica GS09) was used to obtain topographical information along the GPR lines. GPR data are provided in RADAN-Format, dGPS coordinates are provided in ascii format; projection is UTM (WGS 84, zone 21S).

49 ground-penetrating radar lines of Area 2 - Gravel cuspate spit with gravel beach ridges from Potter Cove, King George Island, Antarctic Peninsula

During two field campaigns (Austral springs 2011 and 2012) the sedimentary architecture of a polar gravel-beach system at the southwestern coast of Potter Peninsula (Area 2) was revealed using ground-penetrating radar (GPR, Geophysical Survey Systems, Inc. SIR-3000). 49 profiles were collected using a mono-static 200 MHz antenna operated in common offset mode. Trace increment was set to 0.05 m. A differential global-positioning system (dGPS, Leica GS09) was used to obtain topographical information along the GPR lines. GPR data are provided in RADAN-Format, dGPS coordinates are provided in ascii format; projection is UTM (WGS 84, zone 21S).

Vehicular traffic surveillance and road lane detection using radar interferometry

Speed enforcement on public roadways is an important issue in order to guarantee road security and to reduce the number and seriousness of traffic accidents. Traditionally, this task has been partially solved using radar and/or laser technologies and, more recently, using video-camera based systems. All these systems have significant shortcomings that have yet to be overcome. The main drawback of classical Doppler radar technology is that the velocity measurement fails when several vehicles are in the radars beam. Modern radar systems are able to measure speed and range between vehicle and radar. However, this is not enough to discriminate the lane where the vehicle is driving on. The limitation of several vehicles in the beam is overcome using laser technology. However, laser systems have another important limitation: They cannot measure the speed of several vehicles simultaneously. Novel video-camera systems, based on license plate identification, solve the previous drawbacks, but they have the problem that they can only measure average speed but never top-speed. This paper studies the feasibility of using an interferometric linear frequency modulated continuous wave radar to improve top-speed enforcement on roadways. Two different systems based on down-the-road and across-the-road radar configurations are presented. The main advantage of the proposed solutions is they can simultaneously measure speed, range, and lane of several vehicles, allowing the univocal identification of the offenders. A detailed analysis about the operation and accuracy of these solutions is reported. In addition, the feasibility of the proposed techniques has been demonstrated with simulations and real experiments using a Ka-band interferometric radar developed by our research group.

Multipath Reflectivity Estimation in Urban Environments for Synthetic Aperture Radar Images

Synthetic Aperture Radar (SAR) images a target region reflectivity function in the multi-dimensional spatial domain of range and cross-range. SAR synthesizes a large aperture radar in order to achieve a finer azimuth resolution than the one provided by any on-board real antenna. Conventional SAR techniques assume a single reflection of transmitted waveforms from targets. Nevertheless, today¿s new scenes force SAR systems to work in urban environments. Consequently, multiple-bounce returns are added to directscatter echoes. We refer to these as ghost images, since they obscure true target image and lead to poor resolution. By analyzing the quadratic phase error (QPE), this paper demonstrates that Earth¿s curvature influences the defocusing degree of multipath returns. In addition to the QPE, other parameters such as integrated sidelobe ratio (ISLR), peak sidelobe ratio (PSLR), contrast (C) and entropy (E) provide us with the tools to identify direct-scatter echoes in images containing undesired returns coming from multipath.

Making Transport Safer: V2V-Based Automated Emergency Braking System

An important goal in the field of intelligent transportation systems (ITS) is to provide driving aids aimed at preventing accidents and reducing the number of traffic victims. The commonest traffic accidents in urban areas are due to sudden braking that demands a very fast response on the part of drivers. Attempts to solve this problem have motivated many ITS advances including the detection of the intention of surrounding cars using lasers, radars or cameras. However, this might not be enough to increase safety when there is a danger of collision. Vehicle to vehicle communications are needed to ensure that the other intentions of cars are also available. The article describes the development of a controller to perform an emergency stop via an electro-hydraulic braking system employed on dry asphalt. An original V2V communication scheme based on WiFi cards has been used for broadcasting positioning information to other vehicles. The reliability of the scheme has been theoretically analyzed to estimate its performance when the number of vehicles involved is much higher. This controller has been incorporated into the AUTOPIA program control for automatic cars. The system has been implemented in Citroën C3 Pluriel, and various tests were performed to evaluate its operation.

On the design of a planar phased array radar antenna architecture for space debris situational awareness

The Space Situational Awareness (SSA) program from the European Space Agency (ESA) protects Europe's citizens and their satellite-based services by detecting space hazards. ESA Ground Systems (GS) division is currently designing a phased array radar composed of thousands of radiating elements for future stages of the SSA program [1]. The radar shall guarantee the detection of most of the Low Earth Orbit (LEO) space debris, providing a general map of space junk. While range accuracy is mainly dictated by the radar waveform, the detection and tracking of small objects in LEO regimes is highly dependent on the angular accuracy achieved by the smart phased array antenna, demonstrating the important of the performance of this architecture.

Simulación de seguimiento de blancos en sistemas radar. Parte 2

El proyecto consiste en el diseño y estudio de un software cuyas prestaciones estén orientadas a gestionar una simulación de un sistema de radar. El prototipo de este entorno de simulación se ha realizado en el lenguaje Matlab debido a que inicialmente se considera el más adecuado para el tratamiento de las señales que los sistemas de radar manejan para realizar sus cálculos. Se ha escogido como modelo el software desarrollado por la compañía SAP para gestionar los E.R.P.s de grandes empresas. El motivo es que es un software cuyo diseño y funcionalidad es especialmente adecuado para la gestión ordenada de una cantidad grande de datos diversos de forma integrada. Diseñar e implementar el propio entorno es una tarea de enorme complejidad y que requerirá el esfuerzo de una cantidad importante de personas; por lo que este proyecto se ha limitado, a un prototipo básico con una serie de características mínimas; así como a indicar y dejar preparado el camino por el que deberán transcurrir las futuras agregaciones de funcionalidad o mejoras. Funcionalmente, esto es, independientemente de la implementación específica con la que se construya el entorno de simulación, se ha considerado dividir las características y prestaciones ofrecidas por el sistema en bloques. Estos bloques agruparán los componentes relacionados con un aspecto específico de la simulación, por ejemplo, el bloque 1, es el asignado a todo lo relacionado con el blanco a detectar. El usuario del entorno de simulación interactuará con el sistema ejecutando lo que se llaman transacciones, que son agrupaciones lógicas de datos a introducir/consultar en el sistema relacionados y que se pueden ejecutar de forma independiente. Un ejemplo de transacción es la que permite mantener una trayectoria de un blanco junto con sus parámetros, pero también puede ser una transacción la aplicación que permite por ejemplo, gestionar los usuarios con acceso al entorno. Es decir, las transacciones son el componente mínimo a partir del cual el usuario puede interactuar con el sistema. La interfaz gráfica que se le ofrecerá al usuario, está basada en modos, que se pueden considerar “ventanas” independientes entre sí dentro de las cuáles el usuario ejecuta sus transacciones. El usuario podrá trabajar con cuantos modos en paralelo desee y cambiar según desee entre ellos. La programación del software se ha realizado utilizando la metodología de orientación a objetos y se ha intentado maximizar la reutilización del código así como la configurabilidad de su funcionalidad. Una característica importante que se ha incorporado para garantizar la integridad de los datos es un diccionario sintáctico. Para permitir la persistencia de los datos entre sesiones del usuario se ha implementado una base de datos virtual (que se prevé se reemplace por una real), que permite manejar, tablas, campos clave, etc. con el fin de guardar todos los datos del entorno, tanto los de configuración que solo serían responsabilidad de los administradores/desarrolladores como los datos maestros y transaccionales que serían gestionados por los usuarios finales del entorno de simulación. ABSTRACT. This end-of-degree project comprises the design, study and implementation of a software based application able to simulate the various aspects and performance of a radar system. A blueprint for this application has been constructed upon the Matlab programming language. This is due to the fact that initially it was thought to be the one most suitable to the complex signals radar systems usually process; but it has proven to be less than adequate for all the other core processes the simulation environment must provide users with. The software’s design has been based on another existing software which is the one developed by the SAP company for managing enterprises, a software categorized (and considered the paradigm of) as E.R.P. software (E.R.P. stands for Enterprise Resource Planning). This software has been selected as a model because is very well suited (its basic features) for working in an orderly fashion with a pretty good quantity of data of very diverse characteristics, and for doing it in a way which protects the integrity of the data. To design and construct the simulation environment with all its potential features is a pretty hard task and requires a great amount of effort and work to be dedicated to its accomplishment. Due to this, the scope of this end-of-degree project has been focused to design and construct a very basic prototype with minimal features, but which way future developments and upgrades to the systems features should go has also been pointed. In a purely functional approach, i.e. disregarding completely the specific implementation which accomplishes the simulation features, the different parts or aspects of the simulation system have been divided and classified into blocks. The blocks will gather together and comprise the various components related with a specific aspect of the simulation landscape, for example, block number one will be the one dealing with all the features related to the radars system target. The user interaction with the system will be based on the execution of so called transactions, which essentially consist on bunches of information which logically belong together and can thus be managed together. A good example, could be a transaction which permits to maintain a series of specifications for target’s paths; but it could also be something completely unrelated with the radar system itself as for example, the management of the users who can access the system. Transactions will be thus the minimum unit of interaction of users with the system. The graphic interface provided to the user will be mode based, which can be considered something akin to a set of independent windows which are able on their own to sustain the execution of an independent transaction. The user ideally should be able to work with as many modes simultaneously as he wants to, switching his focus between them at will. The approach to the software construction has been based on the object based paradigm. An effort has been made to maximize the code’s reutilization and also in maximizing its customizing, i.e., same sets of code able to perform different tasks based on configuration data. An important feature incorporated to the software has been a data dictionary (a syntactic one) which helps guarantee data integrity. Another important feature that allow to maintain data persistency between user sessions, is a virtual relational data base (which should in future times become a real data base) which allows to store data in tables. The data store in this tables comprises both the system’s configuration data (which administrators and developers will maintain) and also master and transactional data whose maintenance will be the end users task.