Blue, Green and Orange-Red Light Emitting Polymers: Synthesis, Characterization and Prospects of Applications in Optoelectronic Devices

Light emitting polymers (LEPs) are considered as the second generation of conducting polymers. A Prototype LEP device based on electroluminescence emission of poly(p-phenylenevinylene) (PPV) was first assembled in 1990. LEPs have progressed tremendously over the past 20 years. The development of new LEP derivatives are important because polymer light emitting diodes (PLEDs) can be used for the manufacture of next-generation displays and other optoelectronic applications such as lasers, photovoltaic cells and sensors. Under this circumstance, it is important to understand thermal, structural, morphological, electrochemical and photophysical characteristics of luminescent polymers. In this thesis the author synthesizes a series of light emitting polymers that can emit three primary colors (RGB) with high efficiency

Polymeric electronic gas sensor for determining alcohol content in automotive fuels

In this paper we describe the electrosynthesis of poly[(2-bromo-5-hexyloxy- 1,4-phenylenevinylene)-co-(1,4-phenylenevinylene)] (BHPPV-co-PPV), a novel conducting copolymer, and its application as active layer of a chemiresistive gas sensor suitable for quantification of ethanol present in ethanol-gasoline mixtures normally present in the fuel tanks of flex-fuel vehicles. This information is crucial for the smooth operation of the engine since it permits optimal air:fuel ratio regulation. The sensor consists of an interdigitated electrode coated with a thin polymer film doped with dodecylbenzenesulfonic acid. On exposure to fuel vapours at room temperature, the device presents a linear correlation between its electrical conductance and the ethanol concentration in the fuel. (C) 2008 Elsevier B.V. All rights reserved.

A selective conductive polymer-based sensor for volatile halogenated organic compounds (VHOC)

A novel poly(p-xylylene), PPX, derivative bearing alkoxyphenyl side groups was electrochemically synthesized in 87% yield. The polymer, poly(4`-hexyloxy-2,5-biphenyleneethylene) (PHBPE), presented a fraction (92%) soluble in common organic solvents. It showed to be thermally resistant up to 185 degrees C. UV-vis analysis revealed an E-gap of 3.5 eV Gas sensors made from thin films of 10-camphorsulfonic acid-doped PHBPE deposited on interdigitated electrodes exhibited significant changes in electrical conductance upon exposure to five VHOCs: 1,2-dichloroethane, bromochloromethane, trichloromethane, dichloromethane and tetrachloromethane. The conductance decreased after exposure to tetrachloromethane and increased after exposure to all the other VHOCs. Three-dimensional plots of relative response versus time of half response versus time of half recovery showed good discrimination between the five VHOCs tested. (c) 2008 Elsevier B.V. All rights reserved.

Photoinduced hole-transfer in semiconducting polymer/low-bandgap cyanine dye blends: evidence for unit charge separation quantum yield

Power-conversion efficiencies of organic heterojunction solar cells can be increased by using semiconducting donor-acceptor materials with complementary absorption spectra extending to the near-infrared region. Here, we used continuous wave fluorescence and absorption, as well as nanosecond transient absorption spectroscopy to study the initial charge transfer step for blends of a donor poly(p-phenylenevinylene) derivative and low-band gap cyanine dyes serving as electron acceptors. Electron transfer is the dominant relaxation process after photoexcitation of the donor. Hole transfer after cyanine photoexcitation occurs with an efficiency close to unity up to dye concentrations of similar to 30 wt%. Cyanines present an efficient self-quenching mechanism of their fluorescence, and for higher dye loadings in the blend, or pure cyanine films, this process effectively reduces the hole transfer. Comparison between dye emission in an inert polystyrene matrix and the donor matrix allowed us to separate the influence of self-quenching and charge transfer mechanisms. Favorable photovoltaic bilayer performance, including high open-circuit voltages of similar to 1 V confirmed the results from optical experiments. The characteristics of solar cells using different dyes also highlighted the need for balanced adjustment of the energy levels and their offsets at the heterojunction when using low-bandgap materials, and accentuated important effects of interface interactions and solid-state packing on charge generation and transport.

Nanostructured organic layers via polymer demixing for interface-enhanced photovoltaic cells

Significant progress is being made in the photovoltaic energy conversion using organic semiconducting materials. One of the focuses of attention is the morphology of the donor-acceptor heterojunction at the nanometer scale, to ensure efficient charge generation and loss-free charge transport at the same time. Here, we present a method for the controlled, sequential design of a bilayer polymer cell architecture that consists of a large interface area with connecting paths to the respective electrodes for both materials. We used the surface-directed demixing of a donor conjugated/guest polymer blend during spin coating to produce a nanostructured interface, which was, after removal of the guest with a selective solvent, covered with an acceptor layer. With use of a donor poly(p-phenylenevinylene) derivative and the acceptor C-60 fullerene, this resulted in much-improved device performance, with external power efficiencies more than 3 times higher than those reported for that particular material combination so far.

Transporte eletrônico e quiralidade molecular: um estudo de dispositivos orgânicos em sistemas de dois terminais

No presente trabalho, investigamos o transporte eletrônico molecular em dois compostos orgânicos, o Ponceau SS (PSS) e o Oligo-(para)fenileno-vinileno (PPV) através de cálculos ab initio e função de Green de não equilíbrio (FGNE). Estes métodos demonstraram equivalência para a descrição destes dispositivos moleculares. Fizemos cálculos quânticos para o Hamiltoniano derivado de Hartree-Fock (HF) e obtivemos as propriedades de corrente-voltagem (I-V) para as duas estruturas moleculares. Com o método FGNE conseguimos modelar o transporte através de um sistema de multiníveis eletrônicos obtendo a corrente descrevendo as regiões de ressonância e a assimetria do sistema. Como resposta o PSS demonstrou assimetria para polarizações direta e reversa e a ressonância é alcançada mostrando que o dispositivo opere como um transistor molecular bi-direcional. Para o PPV investigamos também as propriedades geométricas através da conexão entre transporte eletrônico e o grau de quiralidade molecular que foi calculado usando o índice quiral que depende apenas das posições atômicas. Obtivemos que moléculas quirais e propriedades estruturais podem induzir uma assimetria no transporte eletrônico, resultando num processo de retificação. Também obtivemos que a resposta elétrica (I-V) e momento de dipolo elétrico são proporcionais ao grau de quiralidade molecular. Estes resultados sugerem que o transporte eletrônico neste sistema pode ser explorado na avaliação do seu grau de quiralidade.

Otimização dos métodos de expressão e solubilização do alérgeno fosfolipase A1 do veneno de Polybia paulista

A vespa social Polybia paulista (Hymenoptera, Vespidae) é bastante abundante e endêmica nos Estados de São Paulo e sul de Minas Gerais. Os indivíduos da espécie causam um elevado número de acidentes de importância médica. Após a ferroada a vítima pode experimentar reações imunológicas locais e/ou sistêmicas, que em alguns casos podem conduzir a anafilaxia e morte. O diagnóstico e terapia de alergia à ferroada de P. paulista é baseado no uso de extrato de veneno bruto o que se associa à ocorrência de reatividade cruzada e reações imunológicas adversas durante a imunoterapia. O uso de alérgenos recombinantes (r) tem-se mostrado como uma alternativa interessante para reduzir o impacto destas desvantagens. Neste trabalho, foram avaliadas diferentes condições para otimizar a expressão recombinante e solubilização dos corpúsculos de inclusão da fosfolipase A1 (Poly p 1) (70kDa) do veneno de P. paulista previamente obtida mediante expressão heteróloga no sistema procariótico, Escherichia coli. Os resultados aqui obtidos contribuirão para aumentar as quantidades do r Poly p 1 necessárias para sua avaliação bioquímica e imunológica, e finalmente para melhorar os resultados do diagnóstico e imunoterapia específica de alergia ao veneno de P. paulista

Otimização dos métodos de expressão e solubilização do alérgeno fosfolipase A1 do veneno de Polybia paulista

A vespa social Polybia paulista (Hymenoptera, Vespidae) é bastante abundante e endêmica nos Estados de São Paulo e sul de Minas Gerais. Os indivíduos da espécie causam um elevado número de acidentes de importância médica. Após a ferroada a vítima pode experimentar reações imunológicas locais e/ou sistêmicas, que em alguns casos podem conduzir a anafilaxia e morte. O diagnóstico e terapia de alergia à ferroada de P. paulista é baseado no uso de extrato de veneno bruto o que se associa à ocorrência de reatividade cruzada e reações imunológicas adversas durante a imunoterapia. O uso de alérgenos recombinantes (r) tem-se mostrado como uma alternativa interessante para reduzir o impacto destas desvantagens. Neste trabalho, foram avaliadas diferentes condições para otimizar a expressão recombinante e solubilização dos corpúsculos de inclusão da fosfolipase A1 (Poly p 1) (70kDa) do veneno de P. paulista previamente obtida mediante expressão heteróloga no sistema procariótico, Escherichia coli. Os resultados aqui obtidos contribuirão para aumentar as quantidades do r Poly p 1 necessárias para sua avaliação bioquímica e imunológica, e finalmente para melhorar os resultados do diagnóstico e imunoterapia específica de alergia ao veneno de P. paulista

Processi di biorefining per l'estrazione di secondary chemical building blocks da sottoprotti dell'agro-industria

Phenol and cresols represent a good example of primary chemical building blocks of which 2.8 million tons are currently produced in Europe each year. Currently, these primary phenolic building blocks are produced by refining processes from fossil hydrocarbons: 5% of the world-wide production comes from coal (which contains 0.2% of phenols) through the distillation of the tar residue after the production of coke, while 95% of current world production of phenol is produced by the distillation and cracking of crude oil. In nature phenolic compounds are present in terrestrial higher plants and ferns in several different chemical structures while they are essentially absent in lower organisms and in animals. Biomass (which contain 3-8% of phenols) represents a substantial source of secondary chemical building blocks presently underexploited. These phenolic derivatives are currently used in tens thousand of tons to produce high cost products such as food additives and flavours (i.e. vanillin), fine chemicals (i.e. non-steroidal anti-inflammatory drugs such as ibuprofen or flurbiprofen) and polymers (i.e. poly p-vinylphenol, a photosensitive polymer for electronic and optoelectronic applications). European agrifood waste represents a low cost abundant raw material (250 millions tons per year) which does not subtract land use and processing resources from necessary sustainable food production. The class of phenolic compounds is essentially constituted by simple phenols, phenolic acids, hydroxycinnamic acid derivatives, flavonoids and lignans. As in the case of coke production, the removal of the phenolic contents from biomass upgrades also the residual biomass. Focusing on the phenolic component of agrifood wastes, huge processing and marketing opportunities open since phenols are used as chemical intermediates for a large number of applications, ranging from pharmaceuticals, agricultural chemicals, food ingredients etc. Following this approach we developed a biorefining process to recover the phenolic fraction of wheat bran based on enzymatic commercial biocatalysts in completely water based process, and polymeric resins with the aim of substituting secondary chemical building blocks with the same compounds naturally present in biomass. We characterized several industrial enzymatic product for their ability to hydrolize the different molecular features that are present in wheat bran cell walls structures, focusing on the hydrolysis of polysaccharidic chains and phenolics cross links. This industrial biocatalysts were tested on wheat bran and the optimized process allowed to liquefy up to the 60 % of the treated matter. The enzymatic treatment was also able to solubilise up to the 30 % of the alkali extractable ferulic acid. An extraction process of the phenolic fraction of the hydrolyzed wheat bran based on an adsorbtion/desorption process on styrene-polyvinyl benzene weak cation-exchange resin Amberlite IRA 95 was developed. The efficiency of the resin was tested on different model system containing ferulic acid and the adsorption and desorption working parameters optimized for the crude enzymatic hydrolyzed wheat bran. The extraction process developed had an overall yield of the 82% and allowed to obtain concentrated extracts containing up to 3000 ppm of ferulic acid. The crude enzymatic hydrolyzed wheat bran and the concentrated extract were finally used as substrate in a bioconversion process of ferulic acid into vanillin through resting cells fermentation. The bioconversion process had a yields in vanillin of 60-70% within 5-6 hours of fermentation. Our findings are the first step on the way to demonstrating the economical feasibility for the recovery of biophenols from agrifood wastes through a whole crop approach in a sustainable biorefining process.

Methodische Entwicklung der MALDI-TOF-Massenspektrometrie für Grenzbereiche der Polymeranalytik

Zusammenfassung der DoktorarbeitDie MALDI-TOF-Massenspektrometrie (Matrix Assisted Laser Desorption and Ionisation–Time Of Flight) ist in der Lage, Moleküle mit einem Molekulargewicht bis zu mehreren Hunderttausend Da intakt in die Gasphase zu überführen. Dabei wird die Fragmentierung des Analyten stark eingeschränkt bzw. gänzlich vermieden. Diese Methode findet daher zunehmend Verwendung für die Charakterisierung von Biopolymeren und synthetischen Polymeren. Ziel dieser Arbeit war, die MALDI-TOF-Massenspektrometrie zur Charakterisierung von Makromolekülen einzusetzen, bei denen die konventionellen polymeranalytischen Methoden nur unzureichende Informationen oder gar falsche bzw. gar keine Ergebnisse liefern. Mittels einer methodischen Entwicklung der MALDI-TOF-Massenspektrometrie gelang es, die bisherigen Grenzen der Methode zu erweitern und neue Anwendungsbereiche der Polymeranalytik aufzuzeigen. Anhand der erzielten Ergebnisse wurden darüber hinaus neue Erklärungsansätze formuliert, die zu einem besseren Verständnis des noch immer ungeklärten MALDI-Prozesses beitragen können. Besonders vielversprechend sind zum einen die Ergebnisse der Fragmentionenanalyse synthetischer Polymere und zum anderen die Charakterisierung von unlöslichen PAHs (Polycyclic Aromatic Hydrocarbons). Die Möglichkeiten und Aussagekraft der Fragmentionenanalyse wurde an synthetischen Polymeren getestet. Mit Hilfe dieser neuen Technik konnte die komplizierte Endgruppenverteilung einer Polycarbonat-Probe sowie die Zusammensetzung eines Poly-para-phenylenethynylen-b-Polyethylenoxid-Diblock-Copolymers eindeutig bestimmen werden, während die konventionellen MALDI-Massenspektren nur über einen wesentlich geringeren Informationsgehalt verfügten. Auf dem Gebiet der Analytik von unlöslichen PAHs wurde mit der Entwicklung einer neuen MALDI-Probenvorbereitung eine Methode gefunden, die über die PAH Analytik hinaus von großem Nutzen ist. Diese erstmalig angewendete Probenvorbereitung unterscheidet sich von den üblichen MALDI-Probenpräparationen, indem sie auf die Beteiligung eines Lösungsmittels vollkommen verzichtet. Damit konnte speziell ein unlöslicher, zuvor nicht nachweisbarer PAH von ca. 2700 Da mit MALDI eindeutig charakterisiert werden.

Entwicklung neuartiger stickstoffreicher Polyphenylene

Im Rahmen dieser Arbeit wurden Darstellung und elektronische Anwendungsmöglichkeiten von neuartigen stickstoff- und damit elektronenreichen Poly(para-phenylenen) untersucht. Der Teilbereich „Polycarbazole“ befasst sich mit der Synthese von konjugierten (Stufen)leiterpolymeren auf der Basis von Carbazol. Dazu wurde ein neuer und effizienter Syntheseweg zur Gewinnung von 2,7-Dibromcarbazol entwickelt. Durch die weitere Funktionalisierung von 2,7-Dibromcarbazol gelang es, elektronenreiche Leiterpolymere zu gewinnen, die eine grüne Emissionsfarbe aufwiesen. Mit der Verwendung von R = 2-Decyltetradecyl als löslichkeitsfördernder Seitenkette in einem Poly(2,7-carbazol) konnte erstmals ein hochmolekulares Polycarbazol gewonnen werden. Dieses gut lösliche Poly(2,7-carbazol) erwies sich als ein exzellentes Donatormaterial in Solarzellen, welches in Kombination mit dem Farbstoff PDI eine effiziente Solarzelle ergab. Eine OLED mit einem neuartigen arylierten Polycarbazol als Emittermaterial zeigte eine sehr niedrige Turn-on-Spannung und eine intensive blaue EL-Emission. Das Kapitel über imidazolhaltige Poly(para-phenylene) und Discoten stellt die Darstellung von planarisierten Bisimidazolen vor, welche in hohen Ausbeuten durch eine intramolekulare Buchwald-Reaktion zwischen den Imidazolringen und der zentralen Terphenyleinheit durchgeführte wurde. Die dreistufige Darstellung der Discoten aus einem Terephthalaldehyd-Derivat und einem Benzil erlaubt eine einfache sowie variable Einführung von löslichkeitsfördernden Alkylsubstituenten. Auf diese Weise ist der Zugang zu einer völlig neuartigen Klasse an discotischen Materialien möglich, die eine Kombination aus Discoten auf der Basis von Benzolringen (wie z.B. HBC) mit Heteroaromaten darstellen. Die gewonnenen scheibenförmigen Bisimidazole wiesen dementsprechend auf Selbstanordnung zurückzuführende kolumnare Anordnungen und hexagonale Überstrukturen auf. Im dritten Themengebiet wird der Einbau eines Phthalimidchromophors direkt in das Rückgrad von Polyanilin vorgestellt. Da jegliche Veränderung des Oxidationsgrades zu einer unterschiedlichen Donatorfähigkeit des Polyanilinhauptkette führt, variiert in Abhängigkeit davon das Absorptionsverhalten des eingebauten Farbstoffes. Durch die Einführung des Phthalimidchromophores war es zudem möglich, ein leitfähiges Polymer zu erhalten, das im Gegensatz zum nicht-fluoreszierenden Polyanilin eine intensive gelbe Fluoreszenz (lmax = 547 nm) aufweist.

Synthese und Untersuchung aromatischer Amide und aramidbasierter Blockcopolymere

Aromatische Amide mit p-Verknüpfung bilden die wohl steifste und härteste Klasse organischer Moleküle. Ihre Oligomere und Polymere sind Materialien mit extremer Stabilität und chemischer Robustheit. Die vorliegende Arbeit beschreibt die Synthese wohldefinierter Oligo-(p-benzamid)e (OPBA) bis zum Hepta-(p-benzamid), deren Kristallstruktur und thermisches Verhalten eingehend untersucht werden. Ihre besondere Steifigkeit wird im Folgenden genutzt, um Stab-Knäuel-Copolymere mit wohldefiniertem OPBA-Stab-Block herzustellen. Das Aggregationsverhalten dieser Copolymere wird näher beschrieben und die Aggregate mittels Rasterkraftmikroskopie (RKM) visualisiert und charakterisiert. Ein Schwerpunkt der durchgeführten Forschung befasst sich mit dem Einflu"s chemischer Variationen von Knäuel- und Stabblock auf die Aggregation. Ausgehend von PEG-OPBA-Copolymeren wird gezeigt, wie sich über kontrolliert radikalische Polymerisation responsive Triblöcke herstellen lassen. Das Verhalten dieser Triblöcke in wässriger Lösung wird eingehender untersucht und anhand von Lichstreu- und RKM-Untersuchungen ein Modell entwickelt, welches dieses Verhalten beschreibt. Neben den OPBA beschäftigt sich die Arbeit mit der Synthese wohldefinierter Oligo-p-phenylen-terephthalamide (OPTA). Der Aufbau PEG-basierter Stab-Knäuel-Copolymere mit monodispersem OPTA-Block wird beschrieben und ihre Aggregate mittels RKM dargestellt. Die Copolymere werden verwendet, um verbesserte Haftungseigenschaften an Twaron-Fasern gegenüber reinem PEG zu demonstrieren.

Synthetic strategies of new spin-labelled supramolecular systems

Molecular recognition and self-assembly represent fundamental issues for the construction of supramolecular systems, structures in which the components are held together through non-covalent interactions. The study of host-guest complexes and mechanical interlocked molecules, important examples in this field, is necessary in order to characterize self-assembly processes, achieve more control over the molecular organization and develop sophisticated structures by using properly designed building blocks. The introduction of paramagnetic species, or spin labelling, represents an attractive opportunity that allows their detection and characterization by the Electron Spin Resonance spectroscopy, a valuable technique that provides additional information to those obtained by traditional methods. In this Thesis, recent progresses in the design and the synthesis of new paramagnetic host-guest complexes and rotaxanes characterized by the presence of nitroxide radicals and their investigation by ESR spectroscopy are reported. In Chapter 1 a brief overview of the principal concepts of supramolecular chemistry, the spin labelling approach and the development of ESR methods applied to paramagnetic systems are described. Chapter 2 and 3 are focused on the introduction of radicals in macrocycles as Cucurbiturils and Pillar[n]arenes, due to the interesting binding properties and the potential employment in rotaxanes, in order to investigate their structures and recognition properties. Chapter 4 deals with one of the most studied mechanical interlocked molecules, the bistable [2]rotaxane reported by Stoddart and Heath based on the ciclobis (paraquat-p-phenylene) CBPQT4+, that represents a well known example of molecular switch driven by external stimuli. The spin labelling of analogous architectures allows the monitoring by ESR spectroscopy of the switch mechanism involving the ring compound by tuning the spin exchange interaction. Finally, Chapter 5 contains the experimental procedures used for the synthesis of some of the compounds described in Chapter 2-4.

Einzelmolekülspektroskopische Untersuchung von Rylenfarbstoffen zur elektronischen Wechselwirkung in multichromophoren Systemen und zur thermischen Besetzung molekularer Schwingungszustände

Im ersten Teil der Arbeit wurde die Abstandsabhängigkeit des elektronischen Kopplungsverhaltens für eine homologe Reihe von Perylendiimid-Dimeren (PDI-(Ph)x-PDI, x=0-3) mithilfe der Einzelmolekülspektroskopie bei tiefen Temperaturen untersucht. Während für große Abstände überwiegend „schwache“ Kopplung dominierte, wurde für den kleinsten Abstand „starke“ Kopplung gefunden. Im Gegensatz dazu zeigte das p-Phenylen-verbrückte Dimer (x=1) in Abhängigkeit vom untersuchten Molekül ein für beide Grenzfälle typisches Verhalten. Hier entscheidet die Größe der Kopplungsstärke im Vergleich zum statischen Energieunterschied, welcher Kopplungsmechanismus vorliegt. Die homologe Reihe ermöglichte zusätzlich die quantitative Untersuchung der Abstandsabhängigkeit der elektronischen Kopplungsstärke im Grenzfall „schwacher“ Kopplung. Sie konnte direkt aus der zugrunde liegenden Energietransferdynamik ermittelt werden. Der Vergleich mit quantenchemisch berechneten Werten lieferte eine gute Übereinstimmung. Die Abweichung betrug lediglich 20%.rnIm zweiten Teil der Arbeit wurde die thermische Besetzung der Schwingungszustände einzelner Terrylen-Moleküle untersucht. Im elektronischen Grundzustand konnte sie mithilfe von anti-Stokes-Fluoreszenz infolge von „Hot Band“ Absorption nachgewiesen werden. Darüber hinaus wurde Fluoreszenz aus höheren Schwingungszuständen des elektronisch angeregten Zustandes gefunden, die auf „Hot Band“ Emission infolge von thermischer Besetzung zurückgeführt werden konnte. Durch die Kombination von Emissions- und Anregungsspektroskopie konnte die Temperaturabhängigkeit beider Prozesse im Temperaturbereich von 209-311 K untersucht werden. Sie folgt der Boltzmann-Statistik, was eine Temperaturmessung mit einzelnen Molekülen ermöglicht. rn

MeV ion beam lithography of biocompatible halogenated Parylenes using aperture masks

Parylenes are poly(p-xylylene) polymers that are widely used as moisture barriers and in biomedicine because of their good biocompatibility. We have investigated MeV ion beam lithography using 16O+ ions for writing defined patterns in Parylene-C, which is evaluated as a coating material for the Cochlear Implant (CI) electrode array, a neuroprosthesis to treat some forms of deafness. Parylene-C and -F on silicon and glass substrates as well as 50 μm thick PTFE were irradiated to different fluences (1×1013-1×10161×1013-1×1016 1 MeV 16O+ ions cm−2) through aperture masks under high vacuum and a low pressure (<10−3 mbar) oxygen atmosphere. Biocompatibility of the irradiated and unirradiated surfaces was tested by cell-counting to determine the proliferation of murine spiral ganglion cells. The results reveal that an oxygen ion beam can be used to pattern Parylene-C and -F without using a liquid solvent developer in a similar manner to PTFE but with a ∼25× smaller removal rate. Biocompatibility tests showed no difference in cell adhesion between irradiated and unirradiated areas or ion fluence dependence. Coating the Parylene surface with an adhesion-promoting protein mixture had a much greater effect on cell proliferation.