Tracking the ghost of coevolution in specific plant-insect interactions : the case of the pollination system between the globeflower Trollius europaeus and seven european Chiastocheta flies

This study aims at understanding the evolutionary processes at work in specialized species interactions. Prom the macroevolutionary perspective, coevolution among specialized taxa was proposed to be one of the major processes generating biodiversity. We challenge this idea from the theoretical and practical perspective and through a literature review and show that the major hypotheses linking coevolutionary process with macroevolutionary patterns do not necessarily predict lineage co diversification and parallel speciation, limit¬ing the utility of the comparative phylogenenetic approach for investigating coevolution¬ary processes. We also point to the rarity of observed long-term coevolutionary dynamics among lineages and propose that coevolution rather occurs in shorter timescales, followed by ecological fitting. Prom the empirical point, we focus on the nursery pollination interaction between the European globeflower Trollius europaeus (Ranunculaceae) and its associated Chiastocheta flies (Anthomyiidae; Diptera) as a model system of evolution and maintenance of special¬ized interactions. The flies are obligate parasites of the seeds, but also pollinate the plant - it was thus proposed that both species are mutually dependent. Contrasting with the paradigm used for two decades of research on this system, we show that the female fitness component of the plant is similar in the populations with and without Chiastocheta. The plant is thus not exclusively dependent on the flies for reproduction. We discuss this result in the context of the factors responsible for the evolution of mutualistic systems. Understanding the evolution of a biological system requires understanding of its phylo- genetic context. Previous studies showed large mismatch between mtDNA phylogeny and morphological taxonomy in Chiastocheta. By using a large set of RAD-sequencing loci, we delineate the species limits that are congruent with morphology, and show that the discordance is best explained by the scenario of mitochondrial capture among fly species. Finally, we examine this system from a phylogeographic perspective, and identify the lack of congruence in spatial genetic structures of the plant and associated insects across their whole geographic range. The flies show lower numbers of spatial genetic groups than the plant, indicating that not all of the plant réfugia were shared by all the fly species or that the migration dynamics homogenized some of the groups. The incongruence in spatial genetic patterns indicates that fly migrations were largely independent from the genetic background of the plant, following rather a scenario of resource tracking, without the signature of coevolutionary process at this scale. Indeed, while the flies require the plant to survive climatic oscillations, the opposite is not true. Eventually, we show that there is no phylogenetic signal of spatial genetic structures, meaning that neither histories nor life- history traits are shared among closely related species and that species are characterized by unique trajectories of their genes. -- Cette étude vise à comprendre les processus évolutifs à l'oeuvre au sein d'interactions en¬tre espèces spécialisées. Du point de vue macroévolutif, la coévolution entre les taxons spécialisée a été considérée comme l'un des principaux processus générateur de biodiversité. Nous contestons cette idée du point de vue théorique et pratique à travers une revue de la littérature. Nous montrons que les hypothèses majeures reliant les processus coévolutifs avec les patterns de diversité au niveau macroévolutif ne prédisent pas nécessairement la co- diversification des lignées et leur spéciation parallèle, ce qui limite l'utilité de l'approche de phylogénie comparative pour étudier les processus coévolutifs . Nous rappelons également le peu d'exemples de dynamique coévolutive à long terme et proposons que la coévolution se produit plutôt dans des intervalles courts, suivis d'ajustements écologiques. Du point empirique, nous nous concentrons sur l'interaction de pollinisation entre le Trolle d'Europe Trollius europaeus (Ranunculaceae) et ses pollinisateurs associés, du genre Chiastocheta (Anthomyiidae; Diptera) en tant que système-modèle pour étudier l'évolution et le maintien des interactions spécialisées. Les mouches sont des parasites obligatoires des semences, mais pollinisent également la plante. Il a donc été proposé que les deux espèces soient mutuellement dépendantes. Contrastant avec le paradigme utilisé pendant deux décennies de recherche sur ce système, nous montrons, que la composante de fitness femelle de la plante est similaire dans les populations avec et sans Chiastocheta. La plante ne dépend donc pas exclusivement de son interaction avec les mouches pour la reproduction. Nous discutons de ce résultat dans le contexte des facteurs responsables de l'évolution des systèmes mutualistes. Comprendre l'évolution d'un système biologique nécessite la compréhension de son con- texte phylogénétique. Des études antérieures ont montré, chez Chiastocheta, de grandes disparités entre les phylogénies obtenues à partir d'ADN mitochondrial et la taxonomie basée sur les critères morphologiques. En utilisant un grand nombre de loci obtenus par RAD-sequencing, nous traçons les limites des espèces, qui concordent avec les car¬actéristiques morphologies, et montrons que la discordance s'explique en fait par un scénario de capture mitochondriale entre espèces de mouches. Enfin, nous examinons le système d'un point de vue phylogéographique, et identi¬fions les incohérences entre structurations génétiques spatiales de la plante et des insectes associés dans toute leur aire de distribution géographique. Les mouches présentent un nombre de groupes génétiques inférieur à la plante, indiquant que tous les refuges de la plante n'étaient pas partagés par toutes les espèces de mouches ou que les dynamiques migratoires ont homogénéisés certains des groupes chez les mouches. Les différences ob¬servées dans les patrons de structuration génétique spatiale indique que les migrations et dispersions des mouches ont été indépendantes du contexte génétique de la plante, et ces dernières ont été uniquement tributaires de la disponibilité des ressources, sans qu'il n'y ait de signature du processus de coévolution à cette échelle. En effet, tandis que les mouches ont besoin de la plante pour survivre aux oscillations climatiques, le contraire n'est pas exact. Finalement, nous montrons qu'il n'y a pas de signal phylogénétique des structurations génétiques spatiales chez les mouches, ce qui signifie que ni l'histoire, ni les traits d'histoire de vie ne sont partagés entre les espèces phylogénétiquement proches et que les espèces sont caractérisées par des trajectoires uniques de leurs gènes.

System Investigation for Hybrid Electric Vehicle

A hybrid electric vehicle is a fast-growing concept in the field of vehicle industry. Nowadays two global problems make manufactures to develop such systems. These problems are: the growing cost of a fuel and environmental pollution. Also development of controlled electric drive with high control accuracy and reliability allows improving of vehicle drive characteristics. The objective of this Diploma Thesis is to investigate the possibilities of electrical drive application for new principle of parallel hybrid vehicle system. Electric motor calculations, selection of most suitable control system and other calculations are needed. This work is not final work for such topic. Further investigation with more precise calculations, modeling, measurements and cost calculations are needed to answer the question if such system is efficient.

Developing of the Variable Speed Drive -control in simulated parallel pumping systems

This thesis presents briefly the basic operation and use of centrifugal pumps and parallel pumping applications. The characteristics of parallel pumping applications are compared to circuitry, in order to search analogy between these technical fields. The purpose of studying circuitry is to find out if common software tools for solving circuit performance could be used to observe parallel pumping applications. The empirical part of the thesis introduces a simulation environment for parallel pumping systems, which is based on circuit components of Matlab Simulink —software. The created simulation environment ensures the observation of variable speed controlled parallel pumping systems in case of different controlling methods. The introduced simulation environment was evaluated by building a simulation model for actual parallel pumping system at Lappeenranta University of Technology. The simulated performance of the parallel pumps was compared to measured values of the actual system. The gathered information shows, that if the initial data of the system and pump perfonnance is adequate, the circuitry based simulation environment can be exploited to observe parallel pumping systems. The introduced simulation environment can represent the actual operation of parallel pumps in reasonably accuracy. There by the circuitry based simulation can be used as a researching tool to develop new controlling ways for parallel pumps.

Particle detector link system modifications in RE1/1 sector

The large hadron collider constructed at the European organization for nuclear research, CERN, is the world’s largest single measuring instrument ever built, and also currently the most powerful particle accelerator that exists. The large hadron collider includes six different experiment stations, one of which is called the compact muon solenoid, or the CMS. The main purpose of the CMS is to track and study residue particles from proton-proton collisions. The primary detectors utilized in the CMS are resistive plate chambers (RPCs). To obtain data from these detectors, a link system has been designed. The main idea of the link system is to receive data from the detector front-end electronics in parallel form, and to transmit it onwards in serial form, via an optical fiber. The system is mostly ready and in place. However, a problem has occurred with innermost RPC detectors, located in sector labeled RE1/1; transmission lines for parallel data suffer from signal integrity issues over long distances. As a solution to this, a new version of the link system has been devised, a one that fits in smaller space and can be located within the CMS, closer to the detectors. This RE1/1 link system has been so far completed only partially, with just the mechanical design and casing being done. In this thesis, link system electronics for RE1/1 sector has been designed, by modifying the existing link system concept to better meet the requirements of the RE1/1 sector. In addition to completion of the prototype of the RE1/1 link system electronics, some testing for the system has also been done, to ensure functionality of the design.

Parallel-Operating Three-Phase Voltage Source Inverters – Circulating CurrentModeling, Analysis and Mitigation

The maximum realizable power throughput of power electronic converters may be limited or constrained by technical or economical considerations. One solution to this problemis to connect several power converter units in parallel. The parallel connection can be used to increase the current carrying capacity of the overall system beyond the ratings of individual power converter units. Thus, it is possible to use several lower-power converter units, produced in large quantities, as building blocks to construct high-power converters in a modular manner. High-power converters realized by using parallel connection are needed for example in multimegawatt wind power generation systems. Parallel connection of power converter units is also required in emerging applications such as photovoltaic and fuel cell power conversion. The parallel operation of power converter units is not, however, problem free. This is because parallel-operating units are subject to overcurrent stresses, which are caused by unequal load current sharing or currents that flow between the units. Commonly, the term ’circulatingcurrent’ is used to describe both the unequal load current sharing and the currents flowing between the units. Circulating currents, again, are caused by component tolerances and asynchronous operation of the parallel units. Parallel-operating units are also subject to stresses caused by unequal thermal stress distribution. Both of these problemscan, nevertheless, be handled with a proper circulating current control. To design an effective circulating current control system, we need information about circulating current dynamics. The dynamics of the circulating currents can be investigated by developing appropriate mathematical models. In this dissertation, circulating current models aredeveloped for two different types of parallel two-level three-phase inverter configurations. Themodels, which are developed for an arbitrary number of parallel units, provide a framework for analyzing circulating current generation mechanisms and developing circulating current control systems. In addition to developing circulating current models, modulation of parallel inverters is considered. It is illustrated that depending on the parallel inverter configuration and the modulation method applied, common-mode circulating currents may be excited as a consequence of the differential-mode circulating current control. To prevent the common-mode circulating currents that are caused by the modulation, a dual modulator method is introduced. The dual modulator basically consists of two independently operating modulators, the outputs of which eventually constitute the switching commands of the inverter. The two independently operating modulators are referred to as primary and secondary modulators. In its intended usage, the same voltage vector is fed to the primary modulators of each parallel unit, and the inputs of the secondary modulators are obtained from the circulating current controllers. To ensure that voltage commands obtained from the circulating current controllers are realizable, it must be guaranteed that the inverter is not driven into saturation by the primary modulator. The inverter saturation can be prevented by limiting the inputs of the primary and secondary modulators. Because of this, also a limitation algorithm is proposed. The operation of both the proposed dual modulator and the limitation algorithm is verified experimentally.

Permanent Magnet Synchronous Machine for Parallel Hybrid Vehicle

The aim of this thesis is to describe hybrid drive design problems, the advantages and difficulties related to the drive. A review of possible hybrid constructions, benefits of parallel, series and series-parallel hybrids is done. In the thesis analytical and finite element calculations of permanent magnet synchronous machines with embedded magnets were done. The finite element calculations were done using Cedrat’s Flux 2D software. This machine is planned to be used as a motor-generator in a low power parallel hybrid vehicle. The boundary conditions for the design were found from Lucas-TVS Ltd., India. Design Requirements, briefly: • The system DC voltage level is 120 V, which implies Uphase = 49 V (RMS) in a three phase system. • The power output of 10 kW at base speed 1500 rpm (Torque of 65 Nm) is desired. • The maximum outer diameter should not be more than 250 mm, and the maximum core length should not exceed 40 mm. The main difficulties which the author met were the dimensional restrictions. After having designed and analyzed several possible constructions they were compared and the final design selected. Dimensioned and detailed design is performed. Effects of different parameters, such as the number of poles, number of turns and magnetic geometry are discussed. The best modification offers considerable reduction of volume.

Water treatment by multistage filtration system with natural coagulant from Moringa oleifera seeds

This study presents an evaluation of a pilot multistage filtration system (MSF) with different dosages, 131 mg L-1 and 106 mg L-1, of the natural coagulant extracted from Moringa oleifera seeds in pre-filtration and slow filtration stages, respectively. The system was comprised by a dynamic pre-filter unit, two upflow filters in parallel and four slow filters in parallel, and in one of the four filters had the filter media altered. The performance of the system was evaluated by monitoring some water quality parameters such as: turbidity, apparent color and slow filter load loss. The stages that have received the coagulant solution had better treatment efficiency compared with the steps without it. However, the direct application of the coagulant solution in the slow filter caused rapid clogging of the non-woven blanket and shorter career length.

Dispersal and metacommunity dynamics in a soft-sediment benthic system : how well is the seafloor connected?

Connectivity depends on rates of dispersal between communities. For marine soft-sediment communities continued small-scale dispersal as post-larvae and as adults can be equally important in maintaining community composition, as initial recruitment of substrate by pelagic larvae. In this thesis post-larval dispersal strategies of benthic invertebrates, as well as mechanisms by which communities are connected were investigated. Such knowledge on dispersal is scarce, due to the difficulties in actually measuring dispersal directly in nature, and dispersal has not previously been quantified in the Baltic Sea. Different trap-types were used underwater to capture dispersing invertebrates at different sites, while in parallel measuring waves and currents. Local community composition was found to change predictably under varying rates of dispersal and physical connectivity (waves and currents). This response was, however, dependent on dispersal-related traits of taxa. Actively dispersing taxa will be relatively better at maintaining their position, as they are not as dependent on hydrodynamic conditions for dispersal and will be less prone to be passively transported by currents. Taxa also dispersed in relative proportions that were distinctly different from resident community composition and a significant proportion (40 %) of taxa were found to lack a planktonic larval life-stage. Community assembly was re-started in a large-scale manipulative field experiment over one year across several sites, which revealed how patterns of community composition (α-, β- and λ-diversity) change depending on rates of dispersal. Results also demonstrated that in response to small-scale disturbance, initial recruitment was by nearby-dominant species after which other species arrived from successively further away. At later assembly time, the number of coexisting species increased beyond what was expected purely by local niche requirements (species sorting), transferring regional differences in community composition (β-diversity) to the local scale (α-diversity, mass effect). Findings of this thesis complement more theoretical studies in metacommunity ecology by demonstrating that understanding how and when individuals disperse relative to underlying environmental heterogeneity is key to interpreting how patterns of diversity change across different spatial scales. Such information from nature is critical when predicting responses to, for example, different types of disturbances or management actions in conservation.

Establishment of a health and safety management system according to the OHSAS 18001 standard

The thesis develops guidelines for the implementation of the health and safety management system according to the OHSAS 18001 standard, as well as the feasible threat analysis, project proposal schedule, future system quality improvements and organizational change evaluation. The theoretical part clarifies determination of occupational health and safety, its management system, the OHSAS 18001 standard and integrated management system compounded of triple ISO 14001, ISO 9001 and OHSAS 18001 standards. The literature includes such important aspects as human factor, organizational policies, possible benefits, threats, organizational safety culture, Deming’s quality improvement cycle, system implementation, maintenance and cost matters. The empirical part demonstrates real-life situation by using Andritz Pulp & Paper Oy as a case study. Prior the thesis proposal, Andritz Group is analysed including separate business areas, acquisition and integration strategies, current status of the health and safety management and parallel experiences of the largest business area Andritz Hydro. The proposal is aimed at improving the current health and safety system for the permanent and sub-contracted employees at Andritz Pulp & Paper both in Finland and in various projects globally.

Novel Methods for Error Modeling and Parameter Identification of a Redundant Serial-Parallel Hybrid Robot

To obtain the desirable accuracy of a robot, there are two techniques available. The first option would be to make the robot match the nominal mathematic model. In other words, the manufacturing and assembling tolerances of every part would be extremely tight so that all of the various parameters would match the “design” or “nominal” values as closely as possible. This method can satisfy most of the accuracy requirements， but the cost would increase dramatically as the accuracy requirement increases. Alternatively, a more cost-effective solution is to build a manipulator with relaxed manufacturing and assembling tolerances. By modifying the mathematical model in the controller, the actual errors of the robot can be compensated. This is the essence of robot calibration. Simply put, robot calibration is the process of defining an appropriate error model and then identifying the various parameter errors that make the error model match the robot as closely as possible. This work focuses on kinematic calibration of a 10 degree-of-freedom (DOF) redundant serial-parallel hybrid robot. The robot consists of a 4-DOF serial mechanism and a 6-DOF hexapod parallel manipulator. The redundant 4-DOF serial structure is used to enlarge workspace and the 6-DOF hexapod manipulator is used to provide high load capabilities and stiffness for the whole structure. The main objective of the study is to develop a suitable calibration method to improve the accuracy of the redundant serial-parallel hybrid robot. To this end, a Denavit–Hartenberg (DH) hybrid error model and a Product-of-Exponential (POE) error model are developed for error modeling of the proposed robot. Furthermore, two kinds of global optimization methods, i.e. the differential-evolution (DE) algorithm and the Markov Chain Monte Carlo (MCMC) algorithm, are employed to identify the parameter errors of the derived error model. A measurement method based on a 3-2-1 wire-based pose estimation system is proposed and implemented in a Solidworks environment to simulate the real experimental validations. Numerical simulations and Solidworks prototype-model validations are carried out on the hybrid robot to verify the effectiveness, accuracy and robustness of the calibration algorithms.

Numerical Simulation of the Cavitation in the Hydrodynamic Lubrication of Journal Bearings: a Parallel Algorithm

In this paper we present an algorithm for the numerical simulation of the cavitation in the hydrodynamic lubrication of journal bearings. Despite the fact that this physical process is usually modelled as a free boundary problem, we adopted the equivalent variational inequality formulation. We propose a two-level iterative algorithm, where the outer iteration is associated to the penalty method, used to transform the variational inequality into a variational equation, and the inner iteration is associated to the conjugate gradient method, used to solve the linear system generated by applying the finite element method to the variational equation. This inner part was implemented using the element by element strategy, which is easily parallelized. We analyse the behavior of two physical parameters and discuss some numerical results. Also, we analyse some results related to the performance of a parallel implementation of the algorithm.

Energy-efficient control strategies for variable speed driven parallel pumping systems based on pump operation point monitoring with frequency converters

The pumping processes requiring wide range of flow are often equipped with parallelconnected centrifugal pumps. In parallel pumping systems, the use of variable speed control allows that the required output for the process can be delivered with a varying number of operated pump units and selected rotational speed references. However, the optimization of the parallel-connected rotational speed controlled pump units often requires adaptive modelling of both parallel pump characteristics and the surrounding system in varying operation conditions. The available information required for the system modelling in typical parallel pumping applications such as waste water treatment and various cooling and water delivery pumping tasks can be limited, and the lack of real-time operation point monitoring often sets limits for accurate energy efficiency optimization. Hence, alternatives for easily implementable control strategies which can be adopted with minimum system data are necessary. This doctoral thesis concentrates on the methods that allow the energy efficient use of variable speed controlled parallel pumps in system scenarios in which the parallel pump units consist of a centrifugal pump, an electric motor, and a frequency converter. Firstly, the suitable operation conditions for variable speed controlled parallel pumps are studied. Secondly, methods for determining the output of each parallel pump unit using characteristic curve-based operation point estimation with frequency converter are discussed. Thirdly, the implementation of the control strategy based on real-time pump operation point estimation and sub-optimization of each parallel pump unit is studied. The findings of the thesis support the idea that the energy efficiency of the pumping can be increased without the installation of new, more efficient components in the systems by simply adopting suitable control strategies. An easily implementable and adaptive control strategy for variable speed controlled parallel pumping systems can be created by utilizing the pump operation point estimation available in modern frequency converters. Hence, additional real-time flow metering, start-up measurements, and detailed system model are unnecessary, and the pumping task can be fulfilled by determining a speed reference for each parallel-pump unit which suggests the energy efficient operation of the pumping system.

Toward a-state-of-the-art IR copyright management system: a needs assessment

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

MLTDL - Recommendation system for Digital Libraries

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Stiffness based trajectory planning and feedforward based vibration suppression control of parallel robot machines

The dissertation proposes two control strategies, which include the trajectory planning and vibration suppression, for a kinematic redundant serial-parallel robot machine, with the aim of attaining the satisfactory machining performance. For a given prescribed trajectory of the robot's end-effector in the Cartesian space, a set of trajectories in the robot's joint space are generated based on the best stiffness performance of the robot along the prescribed trajectory. To construct the required system-wide analytical stiffness model for the serial-parallel robot machine, a variant of the virtual joint method (VJM) is proposed in the dissertation. The modified method is an evolution of Gosselin's lumped model that can account for the deformations of a flexible link in more directions. The effectiveness of this VJM variant is validated by comparing the computed stiffness results of a flexible link with the those of a matrix structural analysis (MSA) method. The comparison shows that the numerical results from both methods on an individual flexible beam are almost identical, which, in some sense, provides mutual validation. The most prominent advantage of the presented VJM variant compared with the MSA method is that it can be applied in a flexible structure system with complicated kinematics formed in terms of flexible serial links and joints. Moreover, by combining the VJM variant and the virtual work principle, a systemwide analytical stiffness model can be easily obtained for mechanisms with both serial kinematics and parallel kinematics. In the dissertation, a system-wide stiffness model of a kinematic redundant serial-parallel robot machine is constructed based on integration of the VJM variant and the virtual work principle. Numerical results of its stiffness performance are reported. For a kinematic redundant robot, to generate a set of feasible joints' trajectories for a prescribed trajectory of its end-effector, its system-wide stiffness performance is taken as the constraint in the joints trajectory planning in the dissertation. For a prescribed location of the end-effector, the robot permits an infinite number of inverse solutions, which consequently yields infinite kinds of stiffness performance. Therefore, a differential evolution (DE) algorithm in which the positions of redundant joints in the kinematics are taken as input variables was employed to search for the best stiffness performance of the robot. Numerical results of the generated joint trajectories are given for a kinematic redundant serial-parallel robot machine, IWR (Intersector Welding/Cutting Robot), when a particular trajectory of its end-effector has been prescribed. The numerical results show that the joint trajectories generated based on the stiffness optimization are feasible for realization in the control system since they are acceptably smooth. The results imply that the stiffness performance of the robot machine deviates smoothly with respect to the kinematic configuration in the adjacent domain of its best stiffness performance. To suppress the vibration of the robot machine due to varying cutting force during the machining process, this dissertation proposed a feedforward control strategy, which is constructed based on the derived inverse dynamics model of target system. The effectiveness of applying such a feedforward control in the vibration suppression has been validated in a parallel manipulator in the software environment. The experimental study of such a feedforward control has also been included in the dissertation. The difficulties of modelling the actual system due to the unknown components in its dynamics is noticed. As a solution, a back propagation (BP) neural network is proposed for identification of the unknown components of the dynamics model of the target system. To train such a BP neural network, a modified Levenberg-Marquardt algorithm that can utilize an experimental input-output data set of the entire dynamic system is introduced in the dissertation. Validation of the BP neural network and the modified Levenberg- Marquardt algorithm is done, respectively, by a sinusoidal output approximation, a second order system parameters estimation, and a friction model estimation of a parallel manipulator, which represent three different application aspects of this method.