Amostragem de poluentes gasosos e particulados emitidos pela queima de biomassa vegetal

The use of biomass as an energy source has been increasing in Brazil, with emphasis on the use of wood biomass, such as bark, wood chips and sawdust, that after receiving the appropriate treatment can be used in burners for power generation. However, from this burning are emitted fine particles known as particulate matter and a wide range of toxic organic and inorganic components in the form of gases that contribute greatly to air pollution and global warming, affecting human health, the environment and climate. The objective of this project was the quantification of gaseous and particulate, using and evaluating the equipment DR4000 ( Dataram 4 ) sampling of particulates smaller than 2.5μm and EUROTRON ( Ecoline 4000 ) when sampling gaseous pollutants, emitted from the burning of biomass in real time in the firing burner to a chimney attached biomass . We note that there are no specific rules that establish emission limits for particulate matter with diameter less than 2.5μm that are most harmful to human health and the highest concentrations reached about 800000μg/m3, for smaller diameters. It is noticeable the need for sampling of pollutants especially in industries that use biomass to fuel that could be implanted emission control equipment

Estudo comparativo de dois tipos de painéis de MDP: com adição de papel impregnado e lâminas de bambu

This work is the production of two types of particle boards reconstructed MDP (Medium Density Particleboard), the first with the addition, in the inner layer of particles of impregnated paper, the ratios of 0%, 1%, 5% and 20 %. In the second type of panel MDP was inserted with blades of bamboo species Dendrocalumus giganteus as coatings and structural reinforcement. The MDP panel, used as a basis for both cases has the composition of three layers, two external particles with smaller particle size and an inner layer composed of particles of larger particle sizes. Assays were performed based on physical and mechanical NBR 14.810/2006 for the determination of the board density, thickness swelling, water absorption, moisture content, bending, tension parallel and perpendicular, and testing of particle sizes of the particles did not exists in standard references. The results were analyzed and compared the results of the commercial boards made from 100% eucalyptus, based on the limits specified by the ABNT NBR 14.810/2006. The values of the tests showed similar results indicating normative specifications in a positive way, the possibility of production of MDP with the use of waste paper impregnated. As for the panel with bamboo blades, the tests showed a mechanical performance far superior to MDP market, explaining the study and possible implementation of the bamboo for use where the MDP will suffer greater mechanical stress, such as doors, tops and benches tables

Amostragem de poluentes particulados emitidos pela queima de biomassa em correntes confinadas

It is clear today the ever-accelerating search for new fuels that will eventually replace those that will survive in our society, which are fossil fuels. For this reason, a fuel used since the dawn of humanity and much studied since then, considered the generator of clean, renewable energy, can earn more and more space in the power generation sector, which is biomass. We performed two experiments with two different types of biomass, one from the Amazon rainforest and other pine and eucalyptus as waste from the sawmill UNESP Itapeva. In the first experiment, conducted at the Laboratory of Combustion and Propulsion INPE Cachoeira Paulista were conducted three tests in a chimney with a fan creating forced ventilation, where the biomass was burned and deposited on a support beneath the hood. In the second experiment was conducted to analyze the emission of particulate matter using biomass (waste) from the sawmill on the campus of UNESP experimental Itapeva the burning of it in a burner for heating water for a wood oven. In these experiments we used a particle called DATARAM4 sampler that is capable of sampling both outdoors and inside of pipelines, which is the focus of this work. With this equipment it was possible to measure the concentration of particulate matter in all the firings as above, and compare them to levels acceptable in the current law, always trying to analyze the so-called fine particles, which are those with diameters less than 2.5 μm. Using data obtained from the equipment was also possible to evaluate the diametral distribution of particulate matter in question, and verify which phases of the flares in the concentration and the diameters of the particles are the most critical. In this work we concluded that in all firings conducted concentrations of particulate matter were higher than that allowed by the law, and the diameters were found that are more harmful to human health

Aplicação de painéis fotovoltaicos em residências: estudos de caso em Guaratinguetá e Sevilha (Espanha)

In this paper we discussed the possibility of installing a photovoltaic panel in a house in order to reduce electrical consumption. Brazil is a country with a huge solar resource and photovoltaic technology allows transforming solar energy into electricity, helping to decentralize energy production. To enlarge the field of view, the study compares with the equivalent in a Spanish city, discussing how the law favors the initiative of using this type of energy. It will be seen that, with the encouragement of the government, the project can be done because the installation is amortized over a reasonable period of time, about eight years in Spain and three in Brazil

Análise geoestatística da variabilidade espacial do acabamento com tingidor em painéis de madeira colada lateralmente

Classical statistical techniques which necessarily assume that all sampling units are random and independent were always used in the timber industry. Geostatistics considers that certain phenomena are characterized by spatial dependence: values of sampling units closer to each other tend to be more similar than values of sampling units farther away. This study aimed to characterize the spatial variability of the finishing (dyer) in the upper and lower surfaces of four edge glued panels by using geostatistical methods using geoR. Semivariograms were constructed for the analysis of spatial dependence. The spherical mathematical model was the best fit to the semivariograms generated, and was done the interpolation of the data (kriging) in samples where the distribution of dyer presents spatial dependence. In the bottom surfaces of two panels where the spatial dependence was detected geostatistical methods characterized a very large spatial variability due to the heterogeneous application of the finishing

Estudo da influência das resinas termofixas uréia formaldeído (UF) e melamina formaldeído (MF) nas características físicas e mecânicas de painéis MDF

Thermosetting resins are very important in the production of MDF panels. They act as an adhesive in the process of compacting and consolidating the fiberboard. Thermoset resins commonly used in this process are based resin urea formaldehyde (UF) and melamine formaldehyde (MF). The first has a higher demand due to its low cost and good performance in meeting the specifications and standards. The second has a high cost compared to MF resin, but adds greater value to the MDF panel, because it gives greater moisture resistance. The process of manufacture of MDF boards was briefly presented in this study to facilitate the understanding of the work. Samples of thermosetting resins (UF and MF) were subjected to physical-chemical seeking to relate these results to the technological performance presented by their respective samples of MDF boards. Two other samples of MDF panels were subjected to physical and mechanical tests. Results were analyzed and related to the award of their respective thermoset resin. Instruments like Dahmos Trend Manager ® and Grecon Dax 5000 and TG - DSC analysis were used in this study to assist in the analysis of the results. It was observed that the results of the analysis of thermosetting resins were within the specified. Such resins do not directly influence the technological tests provided by the MDF panels, but it has been found that the process variables such as humidity and fiber production rate interfere with the performance of the resin accelerating the reaction and therefore their influence on the physical-mechanical properties of the panels MDF. Samples of MDF panels with UF and MF met all the specifications required by the Brazilian standard with regard to the technological quality. The increased demand for UF resin market is justified by the service specifications...

Análise do desempenho físico-mecânico de painéis compensados de Pinus sp. produzidos com adesivos aquosos a base de poliacetato de vinila e de homopolímero vinílico

This study aimed to evaluate the physico-mechanical performance of three PVA adhesive formulations according to the Brazilian standards for plywood testing and to evaluate the results with those presented in the technical literature and specified in normative documents. The study presents the production process of the panels, the obtaining of samples and, finally, the implementation of physico-mechanical characterization tests based on plywood Brazilian standards. For the panels production it was used a gramature of 120 g / m² and applied a pressure of 15 bars and two temperature combinations and pressing time for each adhesive. The commercial adhesives used were PVA 1810, PVA 1060 and Vinyltec 239. The physical tests conducted were thickness swelling, density, moisture content and water absorption. The mechanical tests were static flexion, for the determination of elasticity modulus (MOE) and rupture modulus (MOR), and shear in the glue line. Among the three formulations studied none showed good performance in the presence of water. However, other trials in the adhesive showed better results and closer to the commercially equivalent used, in the case the urea-formaldehyde, was the PVA 1810, that can be applied in non-structural uses and in environments without the presence of moisture

Aplicação de adesivos estruturais em painéis de carros

The automobile industry is increasingly interested in reducing vehicle weight for greater speed, lower fuel consumption and emissions, through innovation of materials and processes. One way to do this is to seek the replacement of conventional processes by the use of structural adhesives. Structural adhesives are highly resistant materials, which can replace rivets, bolts and welds allowing the substrate / adhesive assemble is stronger than the substrate itself. One of the major advantages of gluing with respect to welding is its esthetic appearance, since it does not leave marks. For this reason, parts to be soldered require a minimum thickness so that the marks do not appear, since the pieces from gluing have no restriction as to the thickness. By replacing the vibration welding process for gluing process of the instrument panel parts of an automobile, one obtains a reduction of the thickness of the parts and therefore it decreases the weight of the car. This work aims to study the various structural adhesives that already exist on the market to be applied on the instrument panel. The mechanical test performed to measure the maximum adhesive strength was the Lap Shear Test at 23°C (room temperature), -35°C and 85°C. The types of adhesives used were the hot-melt and the bi-component. By the results obtained, it is in favor using the bi-component for application to the union of instrument panel parts

Painéis de Medium Density Fiberboard fabricados com bagaço de cana-de-açúcar e madeira de reflorestamento

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização físico-mecânica de painéis de partículas de bambu com adição de casca de café

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento e avaliação de desempenho de um sistema de posicionamento automático para painéis fotovoltaicos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aproveitamento do resíduo do processamento do café na composição de painéis MDP

A produção de produtos derivados de madeira e bambu vem crescendo nos últimos anos na busca de um aproveitamento mais racional dessas matériasprimas. Este trabalho tem por finalidade, o estudo da aplicação de resíduos do processamento do café em um painel MDP. Os painéis MDP foram produzidos com partículas de bambu da espécie Dendrocalamus giganteus e adição de partículas de casca de café na camada intermediária do painel, unidas por resina poliuretana à base de mamona. A caracterização físico-mecânica foi realizada baseando-se nas especificações da NBR 14810-3 (2006). Os resultados obtidos foram comparados com a norma brasileira NBR 14810-2 (2006), resultando em valores próximos aos comercialmente encontrados.

Propriedades físico-mecânicas de painéis de mdp (medium density particleboard) constituído de bambu e fibra de coco

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Monitoramento do tempo de prensagem e do comportamento da temperatura através da espessura de painéis LVL (Laminated veneer lumber)

The aim of this study was to analyze the behavior of the flow of heat (temperature) through the thickness of panels LVL (Laminated veneer lumber) produced with phenol formaldehyde adhesive, in laboratorial and industrial scales. Experimental program was conducted with five LVL panels (three produced in laboratorial scale and two in industrial scale) with different arrangements of a mix of commercial veneers from tropical pinus from the south region of Sao Paulo State, Brazil, bonded using phenol formaldehyde adhesive. The temperature inside the panels during the pressing process was evaluated using thermocouples type T (cooper-constantan), installed mostly in the center of the glue lines and connected to a data acquisition system. The graphics of temperature as a function of the time showed a gradual increase of temperature up to pre-set values, remaining constant from them. The temperature reached at the center of the panels was adequate to promote the curing of the adhesive. These pre-set values were similar to the minimum values presented by other authors and manufacturers of these adhesives that affirm that temperatures above 100ºC at the center of laminated panels bonded with phenolic adhesives are sufficient to ensure proper cure of the resin. The time necessary for curing of the adhesives confirmed the validity of practical expressions provided by adhesive manufacturers.

Design Participativo para a Sustentabilidade: desenvolvimento de painéis modulares para fechamentos, utilizando bambu associado com terra e resíduos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)