AN INVESTIGATION OF VOLATILE ORGANIC AIR CONTAMINANTS IN THE INDOOR MANUFACTURED HOUSING ENVIRONMENT (TEXAS)

Manufactured housing has been found to have substantial levels of formaldehyde in the indoor air. Because mobile homes are more affordable than conventional housing, there has been a large increase in their use in the U.S. This increase in mobile home use has been substantial in the sunbelt regions such as Texas, where high temperatures and humidities may enhance out-gassing of formaldehyde and other volatile organic compounds from construction and furnishing materials and increase any potential health hazards.^ The influences of environmental, architectural and temporal factors on the presence of indoor formaldehyde and other organic compounds were investigated in conjunction with the Texas Indoor Air Quality Study of manufactured housing. A matched pair of mobile homes, one with electric heating and cooking utilities and the other with propane gas utilities, were used for a series of controlled experiments over a fourteen month period from October, 1982 through November, 1983.^ Over this fourteen month period formaldehyde levels decreased approximately 33%. Daily fluctuations of 20% to 40% were observed even with a constant indoor temperature. An increase in indoor temperature of 8(DEGREES)C doubled the measured formaldehyde concentration. Opening windows resulted in decreases of indoor formaldehyde levels of up to 50%. Studies of the impact of propane as a cooking source showed no increase in formaldehyde levels with stove use.^ The presence and concentration of selected volatile organic compounds is influenced greatest by occupancy. Occupants continually open and close windows and doors, vary the operation and settings (temperature) of air control systems, and vary in their selection of furnishings and use of consumer products, which may act as sources of indoor air contaminants. ^

Organohalogen contaminants in wildlife from the Yangtze River Delta : Development of methods and assessments of legacy and emerging persistent organic pollutants

Rapid economic development has occurred during the past few decades in China with the Yangtze River Delta (YRD) area as one of the most progressive areas. The urbanization, industrialization, agricultural and aquaculture activities result in extensive production and application of chemicals. Organohalogen contaminants (OHCs) have been widely used as i.e. pesticides, flame retardants and plasticizers. They are persistent, bioaccumulative and pose a potential threat to ecosystem and human health. However, limited research has been conducted in the YRD with respect to chemicals environmental exposure. The main objective of this thesis is to investigate the contamination level, distribution pattern and sources of OHCs in the YRD. Wildlife from different habitats are used to indicate the environmental pollution situation, and evaluate selected matrices for use in long term biomonitoring to determine the environmental stress the contamination may cause. In addition, a method is developed for dicofol analysis. Moreover, a specific effort is made to introduce statistic power analysis to assist in optimal sampling design. The thesis results show extensive contamination of OHCs in wildlife in the YRD. The occurrences of high concentrations of chlorinated paraffins (CPs) are reported in wildlife, in particular in terrestrial species, (i.e. short-tailed mamushi snake and peregrine falcon). Impurities and byproducts of pentachlorophenol products, i.e. polychlorinated diphenyl ethers (PCDEs) and hydroxylated polychlorinated diphenyl ethers (OH-PCDEs) are identified and reported for the first time in eggs from black-crowned night heron and whiskered tern. High concentrations of octachlorodibenzo-p-dioxin (OCDD) are determined in these samples. The toxic equivalents (TEQs) of polychlorinated dibenzo-p-dioxin (PCDDs) and polychlorinated dibenzofurans (PCDFs) are at mean levels of 300 and 520 pg TEQ g-1lw (WHO2005 TEQ) in eggs from the two bird species, respectively. This is two orders of magnitude higher than European Union (EU) regulation limit in chicken eggs. Also, a novel pattern of polychlorinated biphenyls (PCBs) with octa- to decaCBs, contributing to as much as 20% of total PCBs therein, are reported in birds. The legacy POPs shows a common characteristic with relatively high level of organochlorine pesticides (i.e. DDT, hexacyclohexanes (HCHs) and Mirex), indicating historic applications. In contrast, rather low concentrations are shown of industrial chemicals such as PCBs and polybrominated diphenyl ethers (PBDEs). A refined and improved analytical method is developed to separate dicofol from its major decomposition compound, 4,4’-dichlorobenzophenone. Hence dicofol is possible to assess as such. Statistic power analysis demonstrates that sampling of sedentary species should be consistently spread over a larger area to monitor temporal trends of contaminants in a robust manner. The results presented in this thesis show high CPs and OCDD concentrations in wildlife. The levels and patterns of OHCs in YRD differ from other well studied areas of the world. This is likely due to the extensive production and use of chemicals in the YRD. The results strongly signal the need of research biomonitoring programs that meet the current situation of the YRD. Such programs will contribute to the management of chemicals and environment in YRD, with the potential to grow into the human health sector, and to expand to China as a whole.

Exposure to volatile organic compounds, particulate matter and fungi in a composting plant

Composting is an important process of solid waste management and it can be used for treatment of a variety of different wastes (green waste, household waste, sewage sludge and more). This process aims to: 1. Reduce the volumes of waste and; 2. Create a valuable product which can be recycled as a soil amendment in agriculture and gardening. A natural self-heating process involving the biological degradation of organic matter under aerobic conditions. The handling of waste and compost is responsible for the release of airborne microorganisms and their compounds in the air. Possible contaminants: a) Dust; b) Mesophilic and thermophilic microorganisms; c) Volatile organic compounds; d) Endotoxins and mycotoxins…. Aim: assess exposure/contamination to: a) Volatile organic compounds (VOCs); b) Particulate matter (PM); c) Fungi. In a composting plant located in Lisbon. An additional goal was to identify the workplace with higher level of contamination. In a totally indoor composting plant. The composting operations consisted: 1º Waste already sorted is unloaded in a reception area; 2º Pretreatment - remove undesirable materials from the process (glass, rocks, plastics, metals…); 3º Anaerobic digestion; 4º Dehydration; 5º Open composting with forced aeration. All the process takes thirteen weeks.

Soil remediation time to achieve clean-up goals II: influence of natural organic matter and water contents

This work reports a relatively rapid procedure for the forecasting of the remediation time (RT) of sandy soils contaminated with cyclohexane using vapour extraction. The RT estimated through the mathematical fitting of experimental results was compared with that of real soils. The main objectives were: (i) to predict the RT of soils with natural organic matter (NOM) and water contents different from those used in experiments; and (ii) to analyse the time and efficiency of remediation, and the distribution of contaminants into the soil matrix after the remediation process, according to the soil contents of: (ii1) NOM; and (ii2) water. For sandy soils with negligible clay contents, artificially contaminated with cyclohexane before vapour extraction, it was concluded that: (i) if the NOM and water contents belonged to the range of the prepared soils, the RT of real soils could be predicted with relative differences not higher than 12%; (ii1) the increase of NOM content from 0% to 7.5% increased the RT (1.8–13 h) and decreased the remediation efficiency (RE) (99–90%) and (ii2) the increase of soil water content from 0% to 6% increased the RT (1.8–4.9 h) and decreased the RE (99–97%). NOM increases the monolayer capacity leading to a higher sorption into the solid phase. Increasing of soil water content reduces the mass transfer coefficient between phases. Concluding, NOM and water contents influence negatively the remediation process, turning it less efficient and more time consuming, and consequently more expensive.

Analysis of pesticide residues in strawberries and soils by GC-MS/MS, LC-MS/MS and two-dimensional GC-timeof- flight MS comparing organic and integrated pest management farming

This study analysed 22 strawberry and soil samples after their collection over the course of 2 years to compare the residue profiles from organic farming with integrated pest management practices in Portugal. For sample preparation, we used the citrate-buffered version of the quick, easy, cheap, effective, rugged, and safe (QuEChERS) method. We applied three different methods for analysis: (1) 27 pesticides were targeted using LC-MS/MS; (2) 143 were targeted using low pressure GC-tandem mass spectrometry (LP-GC-MS/MS); and (3) more than 600 pesticides were screened in a targeted and untargeted approach using comprehensive, two-dimensional gas chromatography time-of-flight mass spectrometry (GC × GC-TOF-MS). Comparison was made of the analyses using the different methods for the shared samples. The results were similar, thereby providing satisfactory confirmation of both similarly positive and negative findings. No pesticides were found in the organic-farmed samples. In samples from integrated pest management practices, nine pesticides were determined and confirmed to be present, ranging from 2 μg kg−1 for fluazifop-pbutyl to 50 μg kg−1 for fenpropathrin. Concentrations of residues in strawberries were less than European maximum residue limits.

Novel LTCC-potentiometric microfluidic device for biparametric analysis of organic compounds carrying plastic antibodies as ionophores: Application to sulfamethoxazole and trimethoprim

Monitoring organic environmental contaminants is of crucial importance to ensure public health. This requires simple, portable and robust devices to carry out on-site analysis. For this purpose, a low-temperature co-fired ceramics (LTCC) microfluidic potentiometric device (LTCC/μPOT) was developed for the first time for an organic compound: sulfamethoxazole (SMX). Sensory materials relied on newly designed plastic antibodies. Sol–gel, self-assembling monolayer and molecular-imprinting techniques were merged for this purpose. Silica beads were amine-modified and linked to SMX via glutaraldehyde modification. Condensation polymerization was conducted around SMX to fill the vacant spaces. SMX was removed after, leaving behind imprinted sites of complementary shape. The obtained particles were used as ionophores in plasticized PVC membranes. The most suitable membrane composition was selected in steady-state assays. Its suitability to flow analysis was verified in flow-injection studies with regular tubular electrodes. The LTCC/μPOT device integrated a bidimensional mixer, an embedded reference electrode based on Ag/AgCl and an Ag-based contact screen-printed under a micromachined cavity of 600 μm depth. The sensing membranes were deposited over this contact and acted as indicating electrodes. Under optimum conditions, the SMX sensor displayed slopes of about −58.7 mV/decade in a range from 12.7 to 250 μg/mL, providing a detection limit of 3.85 μg/mL and a sampling throughput of 36 samples/h with a reagent consumption of 3.3 mL per sample. The system was adjusted later to multiple analyte detection by including a second potentiometric cell on the LTCC/μPOT device. No additional reference electrode was required. This concept was applied to Trimethoprim (TMP), always administered concomitantly with sulphonamide drugs, and tested in fish-farming waters. The biparametric microanalyzer displayed Nernstian behaviour, with average slopes −54.7 (SMX) and +57.8 (TMP) mV/decade. To demonstrate the microanalyzer capabilities for real applications, it was successfully applied to single and simultaneous determination of SMX and TMP in aquaculture waters.

Implementation of membrane processes for improvement of the detection of food contaminants

The EM3E Master is an Education Programme supported by the European Commission, the European Membrane Society (EMS), the European Membrane House (EMH), and a large international network of industrial companies, research centres and universities (http://www.em3e.eu)

Anàlisi dels contaminants orgànics persistents en Citharus linguatula en el litoral català

S’ha estudiat la bioacumulació de contaminants orgànics persistents en el múscul d’una espècie de peix en dos punts del litoral català: al Port de Barcelona i a la costa de Blanes. Citharus linguatula ha estat escollida per les seves característiques d’hàbitats (està més exposada a la contaminació al ser una espècie bentònica). La metodologia emprada consisteix en la homogeneïtzació amb sulfat de sodi i una extracció assistida amb microones amb n-hexà-acetona(1:1 v/v) durant 20 minuts. Els extractes es netegen i es fraccionen amb una columna cromatogràfica d’alúmina que permet la separació dels extractes en dos fraccions: un amb la majoria dels compostos organoclorats (hexaclorbenzè, DDTs, ciclodiens clorats i policlorbifenils) i l’altre amb els isòmers hexaclorciclohexans i els PAHs. Aquestes dos fraccions són posteriorment analitzades en el GC-MS. S’ha pogut corroborar l’elevada presència de PCBs a Barcelona, així com que en aquest punt de mostreig les espècies estan més exposades a la contaminació per organoclorats. S’ha identificat la presència de DDTs en els dos llocs estudiats. Pel que fa als PAHs s’ha pogut observar que a Barcelona també hi ha més presència d’aquests. Cal destacar que la concentració obtinguda dels compostos no es pot donar com a vàlida per l’existència d’indicis d’errors experimentals o d’injecció.

Determinació de compostos orgànics contaminants en aigües residuals industrials

La determinació de compostos orgànics contaminants en aigües residuals d’origen urbà i industrial és un tema que ha suscitat un creixent interès, tant des del punt de vista del problema mediambiental que es deriva de l’abocament d’aquestes aigües al medi aquàtic públic com des de la perspectiva de reutilització de les aigües tractades en processos industrials. La majoria d’aquests contaminants no s’eliminen completament en plantes de tractament d’aigües convencionals, pel que s’han de controlar. Aquest fet implica desenvolupar nous processos de tractament que permetin millorar l'eficiència de l'eliminació de les plantes de tractament convencionals. Per tal d'investigar la presència d'aquests compostos contaminants a baixes concentracions és necessari desenvolupar nous mètodes analítics altament sensibles. En el nostre projecte s'han desenvolupat diferents mètodes analítics per determinar compostos orgànics contaminants en aigües residuals provinents de plantes de tractament d'aigües industrials, urbanes i plantes potabilitzadores, utilizant principalment la microextracció en fase sòlida (SPME) seguida de la cromatografia de gasos acoblada a un espectròmetre de masses (GC-MS). S'ha estudiat la presència de diferents famílies de compostos en aquestes aigües, com són: ftalats, amines alifàtiques primàries i nitrosamines. A més a més, s'han desenvolupat mètodes analítics per determinar amines alifàtiques primàries en llots actius provinents de diferents tipus de plantes de tractament d'aigües i plantes potabilitzadores.

Estudi de les càrregues ambientals del compostatge casolà. Simulació d'un sistema de compostatge domèstic i determinació d'emissions de gasos contaminants

Aquest treball s’enfoca cap l’anàlisi de les emissions de gasos amb un potencial impacte negatiu sobre l’entorn que es poden emetre a l’atmosfera durant el compostatge casolà com són el metà i l’òxid nitrós pel seu paper de gasos d’efecte hivernacle i l’amoníac, però sense oblidar el seguiment dels paràmetres del procés en si i la determinació de la qualitat del compost produït. Durant poc més de 6 mesos s’ha simulat un sistema de compostatge casolà tal i com podria donar‐se en un domicili particular i s’ha confirmat la seva eficàcia en la reducció en pes del residu tractat així com l’obtenció d’un producte final altament estable i d’una qualitat més que acceptable. Pel que fa a les emissions de gasos, les quantitats determinades no són menyspreables. L’experiment s’ha realitzat per triplicat. Les emissions són molt erràtiques i no s’han trobat patrons clars en la seva evolució durant el procés de compostatge més enllà d’una certa correlació entre les emissions d’amoníac i la diferència de temperatures entre l’ambient i l’interior dels compostadors. Cal destacat un elevat grau de biaix en la determinació d’emissions gasoses a petita escala, com és el cas del compostatge casolà. Finalment constatar que la generació de lixiviats en el compostatge domèstic pot ser important donat el contingut en aigua de la matèria orgànica tractada a nivell casolà i el limitat accés a material estructurant sec que es té per a compensar‐les.

Biotransformation and endocrine disruptive effects of contaminants in ringed seals - implications for monitoring and risk assessment

Marine mammals are exposed to persistent organic pollutants (POPs), which may be biotransformed to metabolites some of which are highly toxic. Both POPs and their metabolites may lead to adverse health effects, which have been studied using various biomarkers. Changes in endocrine homeostasis have been suggested to be sensitive biomarkers for contaminant-related effects. The overall objective of this doctoral thesis was to investigate biotransformation capacity of POPs and their potential endocrine disruptive effects in two contrasting ringed seal populations from the low contaminated Svalbard area and from the highly contaminated Baltic Sea. Biotransformation capacity was studied by determining the relationships between congener-specific patterns and concentrations of polychlorinated biphenyls (PCBs), organochlorine pesticides (OCPs), polybrominated diphenyl ethers (PBDEs) and their hydroxyl (OH)- and/or methylsulfonyl (MeSO₂)-metabolites, and catalytic activities of hepatic xenobiotic-metabolizing phase I and II enzymes. The results suggest that the biotransformation of PCBs, PBDEs and toxaphenes in ringed seals depends on the congener-specific halogen-substitution pattern. Biotransformation products detected in the seals included OH-PCBs, MeSO₂-PCBs and –DDE, pentachlorophenol, 4-OHheptachlorostyrene, and to a minor extent OH-PBDEs. The effects of life history state (moulting and fasting) on contaminant status and potential biomarkers for endocrine disruption, including hormone and vitamin homeostasis, were investigated in the low contaminated ringed seal population from Svalbard. Moulting/fasting status strongly affected thyroid, vitamin A and calcitriol homeostasis, body condition and concentrations of POPs and their OH-metabolites. In contrast, moulting/fasting status was not associated with variations in vitamin E levels. Endocrine disruptive effects on multiple endpoints were investigated in the two contrasting ringed seal populations. The results suggest that thyroid, vitamin A and calcitriol homeostasis may be affected by the exposure of contaminants and/or their metabolites in the Baltic ringed seals. Complex and non-linear relationships were observed between the contaminant levels and the endocrine variables. Positive relationships between circulating free and total thyroid hormone concentration ratios and OH-PCBs suggest that OH-PCBs may mediate the disruption of thyroid hormone transport in plasma. Species differences in thyroid and bone-related effects of contaminants were studied in ringed and grey seals from low contaminated references areas and from the highly contaminated Baltic Sea. The results indicate that these two species living at the same environment approximately at the same trophic level respond in a very different way to contaminant exposure. The results of this thesis suggest that the health status of the Baltic ringed seals has still improved during the last decade. PCB and DDE levels have decreased in these seals and the contaminant-related effects are different today than a decade ago. The health of the Baltic ringed seals is still suggested to be affected by the contaminant exposure. At the present level of the contaminant exposure the Baltic ringed seals seem to be at a zone where their body is able to compensate for the contaminant-mediated endocrine disruption. Based on the results of this thesis, several recommendations that could be applied on monitoring and assessing risk for contaminant effects are provided. Circulating OH-metabolites should be included in monitoring and risk assessment programs due to their high toxic potential. It should be noted that endogenous variables may have complex and highly variable responses to contaminant exposure including non-linear responses. These relationships may be further confounded by life history status. Therefore, it is highly recommended that when using variables related to endocrine homeostasis to investigate/monitor or assess the risk of contaminant effects in seals, the life history status of the animal should be carefully taken into consideration. This applies especially when using thyroid, vitamin A or calcitriolrelated parameters during moulting/fasting period. Extrapolations between species for assessing risk for contaminant effects in phocid seals should be avoided.

Ultrasonic and Electrokinetic Remediation of Low Permeability Soil Contaminated with Persistent Organic Pollutants

Electrokinetics has emerged as a potential technique for in situ soil remediation and especially unique because of the ability to work in low permeability soil. In electrokinetic remediation, non-polar contaminants like most organic compounds are transported primarily by electroosmosis, thus the process is effective only if the contaminants are soluble in pore fluid. Therefore, enhancement is needed to improve mobility of these hydrophobic compounds, which tend to adsorb strongly to the soil. On the other hand, as a novel and rapidly growing science, the applications of ultrasound in environmental technology hold a promising future. Compared to conventional methods, ultrasonication can bring several benefits such as environmental friendliness (no toxic chemical are used or produced), low cost, and compact instrumentation. It also can be applied onsite. Ultrasonic energy applied into contaminated soils can increase desorption and mobilization of contaminants and porosity and permeability of soil through developing of cavitation. The research investigated the coupling effect of the combination of these two techniques, electrokinetics and ultrasonication, in persistent organic pollutant removal from contaminated low permeability clayey soil (with kaolin as a model medium). The preliminary study checked feasibility of ultrasonic treatment of kaolin highly contaminated by persistent organic pollutants (POPs). The laboratory experiments were conducted in various conditions (moisture, frequency, power, duration time, initial concentration) to examine the effects of these parameters on the treatment process. Experimental results showed that ultrasonication has a potential to remove POPs, although the removal efficiencies were not high with short duration time. The study also suggested intermittent ultrasonication over longer time as an effective means to increase the removal efficiencies. Then, experiments were conducted to compare the performances among electrokinetic process alone and electrokinetic processes combined with surfactant addition and mainly with ultrasonication, in designed cylinders (with filtercloth separating central part and electrolyte parts) and in open pans. Combined electrokinetic and ultrasonic treatment did prove positive coupling effect compared to each single process alone, though the level of enhancement is not very significant. The assistance of ultrasound in electrokinetic remediation can help reduce POPs from clayey soil by improving the mobility of hydrophobic organic compounds and degrading these contaminants through pyrolysis and oxidation. Ultrasonication also sustains higher current and increases electroosmotic flow. Initial contaminant concentration is an essential input parameter that can affect the removal effectiveness.

Microbiological and physicochemical evaluations of juice extracted from different parts of sugar cane stalks from three varieties cultivated under organic management

The artisanal production of cachaça, a beverage obtained by the fermentation of sugar cane juice after distillation, especially by small-sized producers, has traditionally used natural ferment ("fermento caipira") which consists of sugar cane juice with crushed corn, powdered rice, or citrus fruits. In despite of the difficulties in quality control due to the high level of contaminants and longer periods of preparation, the sensorial quality of the beverage may be attributed to the physiological activities of wild yeasts and even bacteria present during fermentation when this ferment is used. In this context, the aim here was to evaluate the microbiological (yeasts) and physicochemical characteristics of sugar cane juice extracted from different parts of three different varieties (RB72454, RB835486, and RB867515) of the cane stalk (lower, medium, and upper sections) in three harvesting periods (from May to December 2007) in an area under organic management. The juice from the upper section (from the eleventh internode to the top) of the sugar cane stalk could be indicated for the preparation of the natural ferment since it is as a source of yeasts and reducing sugars, especially the variety RB867515. Due to the seasonality, the best period for using this part of the sugar cane stalk is at the beginning of harvesting when the phenolic compounds are at low concentration, but there are higher number of Saccharomyces population and other yeast species. The high acidity in this section of the plant could result in a better control of bacterial contamination. These findings explain the traditional instructions of adding the upper sections for the preparation of natural ferment and can help its management in order to get a better performance with respect to organic cachaça production.

Geochemistry and mineralogical association of heavy metal contaminants in fine grained sediment, Welland River, Southern Ontario /

This investigation of geochemistry and mineralogy of heavy metals in fine grained (<63^m) sediment of the Welland River was imdertaken to: 1) describe metal dispersion patterns relative to a source, identify minerals forming and existing at the outfall region and relate sediment particle size to chemistry; 2) to delineate sample handling, preparation and evaluate, modify and develop analytical methods for heavy metal analysis of complex environmental samples. Ajoint project between Brock University and Geoscience Laboratories was initiated to test a contaminated site of the Welland River at the base of Atlas Speciality Steels Co. Methods were developed and utilized for particle size separation and two acid extraction techniques: 1) Partial extraction; 2) Total extraction. The mineralogical assessment identified calcite, dolomite, quartz and clays. These minerals are typical of the carbonate-shale rock basement of the Niagara Peninsula. Minerals such as, mullite and ferrocolumbite were found at the outfall region. These are not typical of the local geology and are generally associated with industrial pollutants. Partial and total extraction techniques were used to characterize the sediments based on chemical distribution, elemental behaviour and analytical differences. The majority of elements were lower in concentration in the partial extraction technique; suggesting these elements are bound in an acid extractable phase (exchangeable, organic and carbonate phases). The total extraction technique yielded higher elemental concentrations taking difficult oxides and silicates into solution. Geochemical analyses of grain size separates revealed that heavy metal (Co, Ni, V, Mn, Fe, Ba) concentrations did not increase with decreasing grain size. This is a function of the anthropogenic mill scale input into the river. The background elements (Sc, Y, Sr, Mg, Al and Ti) showed an increase in concentration to the finest grain size suggesting that it is directly related to the local mineralogy and geology. Dispersion patterns ofmetals fall into two distinct categories: 1) the heavy metals (Co, Cu, Ni, Zn, V and Cr), and 2) the background elements (Be, Sc, Y, Sr, Al and Ti). The heavy metals show a marked increase in the outfall region, while the background elements show a significant decrease at the outfall. This pattern is attributed to a "dilution effect" ofthe natural sediments by the anthropogenic mill scale sediments. Multivariant statistical analysis and correlation coefficient matrix results clearly support these results and conclusions. These results indicate the outfall region ofthe Welland River is highly contaminated with to heavy metals from the industrialized area of Welland. A short distance downstream, the metal concentrations return to baseline geochemical levels. It appears, contaminants rapidly come out of suspension and are deposited in close proximity to the source. Therefore, it is likely that dredging the sediment from the river may cause resuspension of contaminated sediments, but may not distribute the sediment as far as initially anticipated.

Étude de la sorption et de la désorption de neuf contaminants émergents dans les boues usées

Des études de sorption/désorption ont été effectuées pour neuf contaminants émergents sélectionnés (caféine, sulfaméthoxazole, déséthylatrazine, carbamazépine, atrazine, estradiol, éthinylestradiol, noréthindrone et diclofénac) dans les boues usées provenant de trois systèmes différents. Les contaminants incluent une variété de classes de composés (pesticides, hormones et pharmaceutiques) qui possèdent des propriétés physicochimiques différentes. L’objectif de ces travaux est de modéliser leur comportement dans une station d’épuration, en présence d’une phase particulaire et d’une phase aqueuse, et du même coup, de mieux comprendre leur devenir lors de leur rejet dans l’environnement. Le coefficient octanol-eau (log Kow) permet de bien interpréter les résultats et nous permet de classer les composés selon deux types de comportements observés : les composés avec un log Kow inférieur à 3 montrent peu ou pas de sorption alors que les composés avec un log Kow supérieur à 3 montrent une sorption variant de 30 à 90 % durant les premières minutes, suivi d’une sorption lente durant les heures suivantes. Une augmentation du contenu organique favorise la sorption des composés hydrophobes alors qu’un changement de pH peut modifier la charge à la surface des particules et également la charge des analytes. Les résultats ont montré que seul le diclofénac était sensible aux variations de pH étudiés. Dans une telle situation, il est nécessaire d’utiliser le facteur d’hydrophobicité corrigé en fonction du pH (log Dow). Le coefficient de distribution solide-eau (log Kd) a été déterminé pour chaque composé à la fin de chaque expérience de sorption et se situe entre -0.3 et 2.6. Avec l’augmentation de l’hydrophobicité, la désorption diminue avec le temps et avec l’étape de rinçage. Pour simuler le relargage dans les systèmes aquatiques, les facteurs de rinçage ont été déterminés pour estimer le nombre de rinçages qui seraient nécessaire pour désorber 50 et 99 % de la concentration initialement sorbée. Les bilans de masse ont été effectués après chaque expérience dans le but de ne pas surestimer les capacités de sorption d’un composé et se situent entre 7 et 25 % pour l’estradiol, la noréthindrone et le sulfaméthoxazole et entre 44 et 103 % pour l’éthinylestradiol, l’atrazine, la déséthylatrazine, la carbamazépine, la caféine et le diclofénac.