Push-out Bond Strength of Fiber Posts Luted with Unfilled Resin Cement

Purpose: The study evaluates the behavior of different adhesive systems and resin cements in fiber post placement, with the intent to clarify the possible role of unfilled resin as a luting material for fiber posts. Materials and Methods: Two luting agents (Dual-Link and Unfilled Resin) for cementing fiber posts into root canals were applied either with All-Bond 2 or One-Step Plus, or without an adhesive system, and challenged with the push-out test. Slices of roots restored with posts were loaded until post segment extrusion in the apical-coronal direction. Failure modes were analyzed under SEM. Results: Push-out strength was significantly influenced by the luting agent (p < 0.05), but not by the bonding strategy (p > 0.05). The best results were obtained in combination with Unfilled Resin with One-Step Plus. Dual-Link groups failed mainly cohesively within the cement, while Unfilled Resin demonstrated more adhesive fracture at the post interface. Conclusion: The results of this study support the hypothesis that adhesive unfilled resin application is essential for achieving high bond strength to radicular dentin.

Push-out strength of methacrylate resin-based sealers to root canal walls

P>Aim To assess the push-out strength of Epiphany SE, Epiphany and Hybrid Root SEAL to the dentine walls of root canals. Methodology Sixty roots of canines were prepared and distributed to six groups (n = 10) according to the filling material: GI - Epiphany SE, GII - Epiphany primer and sealer, GIII - Epiphany primer, sealer and resinous solvent, GIV - Clearfil DC Bond and Epiphany sealer, GV - Clearfil, Epiphany sealer and solvent and GVI - Hybrid Root SEAL. Resilon cones were used in all groups. Roots were sectioned transversally to obtain three slices from each third. One slice was subjected to the push-out test (MPa), and results were analysed by anova and Tukey`s test (P < 0.05). The other two slices were prepared for scanning electron microscopy (SEM). Failure mode was also analysed. Results A statistically significant difference (P < 0.05) occurred between Hybrid Root SEAL (5.27 +/- 2.07) and the other materials, GI (0.40 +/- 0.23), GII (0.78 +/- 0.45), GIII (0.57 +/- 0.28), GIV (0.40 +/- 0.24) and GV (0.50 +/- 0.41), which did not differ significantly from each other (P > 0.05). Adhesive failures predominated in groups I, II, IV and V, whilst mixed and cohesive failures were the most frequent in groups III and VI, respectively. There were gaps in the adhesive interface of GI and GII, continuity areas of the filling material with dentine in GIV and GV and good adaptation of the interface of GVI. Conclusion Hybrid Root SEAL had greater push-out strength to root canal dentine than Epiphany SE and Epiphany. The use of primer, solvent and adhesive system did not influence the adhesion of Epiphany.

Rates of gene rearrangement and nucleotide substitution are correlated in the mitochondrial genomes of insects

A number of studies indicated that lineages of animals with high rates of mitochondrial (mt) gene rearrangement might have high rates of mt nucleotide substitution. We chose the hemipteroid assemblage and the Insecta to test the idea that rates of mt gene rearrangement and mt nucleotide substitution are correlated. For this purpose, we sequenced the mt genome of a lepidopsocid from the Psocoptera, the only order of hemipteroid insects for which an entire mtDNA sequence is not available. The mt genome of this lepidopsocid is circular, 16,924 bp long, and contains 37 genes and a putative control region; seven tRNA genes and a protein-coding gene in this genome have changed positions relative to the ancestral arrangement of mt genes of insects. We then compared the relative rates of nucleotide substitution among species from each of the four orders of hemipteroid insects and among the 20 insects whose mt genomes have been sequenced entirely. All comparisons among the hernipteroid insects showed that species with higher rates of gene rearrangement also had significantly higher rates of nucleotide substitution statistically than did species with lower rates of gene rearrangement. In comparisons among the 20 insects, where the mt genomes of the two species differed by more than five breakpoints, the more rearranged species always had a significantly higher rate of nucleotide substitution than the less rearranged species. However, in comparisons where the mt genomes of two species differed by five or less breakpoints, the more rearranged species did not always have a significantly higher rate of nucleotide substitution than the less rearranged species. We tested the statistical significance of the correlation between the rates of mt gene rearrangement and mt nucleotide substitution with nine pairs of insects that were phylogenetically independent from one 2 another. We found that the correlation was positive and statistically significant (R-2 = 0.73, P = 0.01; R-s = 0.67, P < 0.05). We propose that increased rates of nucleotide substitution may lead to increased rates of gene rearrangement in the mt genomes of insects.

The effects of place of residence on tourist motivations: a revised case of the Urban Quadrangle of Minho

This study seeks to capture the underlying reasons for the travel decisions of residents of the Urban Quadrangle of Minho (composed of the municipalities of Barcelos, Braga, Guimarães, and Vila Nova de Famalicão). The aim of the research is three-fold. Firstly, the study identifies the push and pull motivational factors of residents of the Urban Quadrangle of Minho. Secondly, the study examines whether there are differences between the tourist motivations of residents of the four different municipalities of the Urban Quadrangle. Finally, the study investigates if there are any differences in the motivations of those who choose national and international destinations. The methodology comprises quantitative research based on questionnaires administered in 2012 to residents of the Urban Quadrangle of Minho. A principal component factor analysis is employed to identify six push and seven pull factors. The comparison of the mean scores of these factors across municipalities and across residents that choose national and international destinations reveals that the most valued and least valued factors are common to all four municipalities and both groups of residents (that choose national and international destinations).

The effects of place of residence on tourist motivations: the case of Urban Quadrangle of Minho

The aim of this preliminary study is three-fold. Firstly, the study identifies the push and pull motivational factors of residents of the Urban Quadrangle of Minho. Secondly, the study examines whether there are differences between the tourist motivations of residents of the four different municipalities. Finally, the study investigates if there are any differences in the motivations of those who choose national and international destinations.

Tourist motivation of the residents of the Urban Quadrilátero of Minho: a gender analysis

Women are increasingly active in the participation and consumption of tourism, representing a strong and unique market segment. Knowledge of the needs and preferences of female tourists represents a key success factor in the tourism industry. This preliminary study seeks to capture the underlying reasons for the travel decisions of the residents of the Urban Quadrilátero of Minho, investigating their tourist motivations from a gendered perspective. Insight on tourism motivation may be an important policy tool for tourism planners and managers in the development of products and marketing strategies. The empirical analysis is undertaken based on questionnaires administered in 2012 to residents of the Urban Quadrilátero of Minho. Preliminary results do not reveal significant gender differences in the importance that the local residents place on various tourism motivation factors.

Synthesis of new Fe(II) and Ru(II) eta(5)-monocyclopentadienyl compounds showing significant second order NLO properties

A series of new ruthenium(II) complexes of the general formula [Ru(eta(5)-C5H5)(PP)(L)][PF6] (PP = DPPE or 2PPh(3), L = 4-butoxybenzonitrile or N-(3-cyanophenyl)formamide) and the binuclear iron(II) complex [Fe(eta(5)-C5H5)(PP)(mu-L)(PP)(eta(5)-C5H5)Fe][PF6](2) (L = (E)-2-(3-(4-nitrophenyl)allylidene)malononitrile, that has been also newly synthesized) have been prepared and studied to evaluate their potential in the second harmonic generation property. All the new compounds were fully characterized by NMR, IR and UV-Vis spectroscopies and their electrochemistry behaviour was studied by cyclic voltammetry. Quadratic hyperpolarizabilities (beta) of three of the complexes have been determined by hyper-Rayleigh scattering (HRS) measurements at fundamental wavelength of 1500 nm and the calculated static beta(0) values are found to fall in the range 65-212 x 10(-30) esu. Compound presenting beta(0) = 212 x 10(-30) esu has revealed to be 1.2 times more efficient than urea standard in the second harmonic generation (SHG) property, measured in the solid state by Kurtz powder technique, using a Nd:YAG laser (1064 nm). (C) 2013 Elsevier B.V. All rights reserved.

Desperdícios na cadeia logística no âmbito industrial

Projecto apresentado ao Instituto Politécnico do Porto para obtenção do Grau de Mestre em Logística Orientada por Prof. Doutor Gouveia

Benzo[c]thiophene chromophores linked to cationic Fe and Ru derivatives for NLO materials: synthesis characterization and quadratic hyperpolarizabilities

5-Monocyclopentadienyliron(II)/ruthenium(II) complexes of the general formula [M(5-C5H5)(PP)(L1)][PF6] {M = Fe, PP = dppe; M = Ru, PP = dppe or 2PPh3; L1 = 5-[3-(thiophen-2-yl)benzo[c]thiophenyl]thiophene-2-carbonitrile} have been synthesized and studied to evaluate their molecular quadratic hyperpolarizabilities. The compounds were fully characterized by NMR, FTIR and UV/Vis spectroscopy and their electrochemical behaviour studied by cyclic voltammetry. Quadratic hyperpolarizabilities () were determined by hyper-Rayleigh scattering measurements at a fundamental wavelength of 1500 nm. Density functional theory calculations were employed to rationalize the second-order non-linear optical properties of these complexes.

Reforço de lajes de betão armado usando pós-tensãocom ancoragens por aderência

Dissertação para obtenção do Grau de Doutor em Engenharia Civil,Especialidade Estruturas

Controlo e monitorização de um sistema de Auto-Pull

Esta dissertação descreve o estudo do controlo e da monitorização de um sistema de autopull, bem como o estudo da implementação de um destes sistemasnuma área de negócio. Inicialmente, de modo a percecionar as melhores opções a tomar para a realização deste projeto foram estudadas duas redes de comunicação locais, redes Ethernet e redes CAN, tendo-se optado pelas redes Ethernet, sendo as razões que determinaram esta escolha explanadas no desenvolvimento do relatório. Após ter sido selecionada a rede que foi utilizada, foram estudados os requisitos do sistema e procuradas no mercado soluções que os satisfaçam. Para a comunicação em tempo real foram utilizadas Web Sockets e para a utilização destas,foi necessário um servidor de Web Sockets, tendo a escolha recaídosobre onodejs. Posteriormente, foi elaborada uma interface gráfica que permitiu a criação de um sistema inteligente que auxilia os clientes do espaço a efetuarem pedidos bem como a chamarem os funcionários, não necessitando de passar os longos tempos de espera que normalmenteestão associados a estes espaços. Posto isto, foi realizado um website que deverá apresentar o espaço, os próximos eventos a realizar e outras informações importantes. Este sistema torna-se uma mais-valia para a divulgação da tecnologia implementada e para a divulgação dos espaços que eventualmente venham a adotar um sistema análogo. De seguida foi efetuado um plano de negócios, simulando um espaço físico que eventualmente implementasse esta tecnologia. Para tal, foi estudada a envolvente externa e interna em que este negócio estaria inserido, as políticas de marketing que deveriam ser seguidas e ainda um plano financeiro que descrevesse o investimento, as vendas esperadas e todos os restantes componentes económicos do projeto. Por último foram tecidas as principais conclusões inerentes ao projeto desenvolvido e analisadas as possibilidades de melhorias futuras.