In-situ XANES experiments on Ni K-edge in mesoporous ZrO2-CeO2:Ni.

Ordered mesoporous ZrO2-CeO2 mixed oxides are potential candidates for catalytic applications. These systems, used as anodes in solid oxide fuel cells (SOFC), may lead to better performance of SOFCs, due to an enhancement on surface area, aiming to achieve a lower working temperature. The aim of this studies is to evaluate the reduction capacity of Ni2+ to Ni in ZrO2-x(mol)%CeO2 (x=50 and 90) samples impregnated with 60(wt.)%NiO. The synthesis was made with Zr and Ce chloride precursors, HCl aqueous solution, Pluronic P123, NH4OH to adjust the pH (3-4) and a teflon autoclave to perform a hydrothermal treatment (80oC/48h). The samples were dried and calcined, until 540oC in N2 and 4 hours in air. The NiO impregnation was made with an ethanol dispersion of Ni(NO3)£6H2O. The powder was calcinated in air until 350oC for 2 hours. Temperature-resolved XANES data at the Ni K-edge were collected at the DXAS beam line of the LNLS in transmission mode, using a Si(111) monochromator and a CCD detector. Sample preparation consisted of mixing »6mg of the powder samples with boron nitride and pressing into pellets. The data were acquired during an experiment of temperature programmed reduction (TPR) under a 5% H2/He until 600oC and mixtures of 20%CH4:5%O2/He, at temperatures from 400 to 600oC. All the reactions were monitored with a mass spectrometer. The data was analyzed with a linear combination fit of 2 standards for each valence number using Athena software. The Ni K-edge experiments demonstrated that for both contents of CeO2, NiO embedded in the porous zirconia-ceria matrix reduces at lower temperatures than pure NiO, revealing that the ZrO2-CeO2 support improves the reduction of impregnated NiO. Ni was oxidized to NiO after all reactions with methane and oxygen. Hydrogenated carbonaceous species were detected, but under reducing conditions, the hydrocarbon compounds are removed. The reaction of total oxidation of methane CH4:O2 (1:2 ratio) was observed at lower temperatures (around 400oC) for both samples.

Natural oxides, elements and remanent magnetization intensities and directions at DSDP Hole 93-603B

Dark green spherules occur in the lower part of a turbidite in Section 603B-22-3, at the 70 cm level. In all probability these spherules originally consisted of massive glass, but now appear to have become completely altered into smectite. The presence of numerous microscopic fissures in the spherules probably mediated in the alteration process. Judging by the presence of similar spherules at the Cretaceous/Tertiary (K/T) boundary in DSDP Hole 390B, the green spherules are thought to represent diagenetically altered impact ejecta from one large or several smaller extraterrestrial objects at the end of the Cretaceous. The presence of anomalously high concentrations of Ni, Co, and As higher up in the turbidite are in agreement with an expected enrichment of these elements in the K/T boundary clay. However, precise Ir analyses are necessary in order to confirm this.

Concentrations of Fe, Mn, Cu, Zn, Co, Ni, Pb, Cd, B, and SiO2 in interstitial waters from bottom sediments of the Atlantis II and Discovery Deeps, Red Sea rift zone

Chemical analyzes show that interstitial waters from ore-bearing bottom sediments of the Atlantis II and Discovery Deeps are enriched in Fe, Mn, Cu, Ni, Co, Zn, Pb, and Cd compared to sea water. Enrichment factors of these trace elements in the interstitial waters of the Atlantis II Deep relative to the sea water vary within the following ranges: for Fe from 100 to 7000, for Mn from 19047 to 32738, for Zn from 500 to 1600, for Pb from 78333 to 190000, for Cu from 107 to 654. Comparison of average weighted concentrations of Fe, Mn, Zn, Pb, Cu, Ni in the bottom sediments and the interstitial waters of the Atlantis II Deep indicates common regularities and good relationship in distribution of these elements along sediment cores. Differences in concentrations and distribution of the studied trace elements in the interstitial waters of the Atlantis II and Discovery Deeps result from different chemical compositions of hydrothermal fluids entering these deeps.

Preferential oxidation of CO in excess of H2 on Pt/CeO2–Nb2O5 catalysts

A series of CeO2–Nb2O5 mixed oxides with different Nb content, as well as the pure oxides, have been synthesized by co-precipitation with excess urea. These materials have been used as supports for platinum catalysts, with [Pt(NH3)4](NO3)2 as precursor. Both supports and catalysts have been characterized by several techniques: N2 physisorption at 77 K, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, UV–vis spectroscopy, scanning electron microscopy, transmission electron microscopy, temperature-programmed reduction and temperature-programmed desorption (CO and H2), and their catalytic behaviour has been determined in the PROX reaction, both with an ideal gas mixture (CO, O2 and H2) and in simulated reformate gas containing CO2 and H2O. Raman spectroscopy analysis has shown the likely substitution of some Ce4+ cations by Nb5+ to some extent in supports with low niobium contents. Moreover, the presence of Nb in the supports hinders their ability to adsorb CO and to oxidize it to CO2. However, an improvement of the catalytic activity for CO oxidation is obtained by adding Nb to the support, although the Pt/Nb2O5 catalyst shows very low activity. The best results are found with the Pt/0.7CeO2–0.3Nb2O5 catalyst, which shows a high CO conversion (85%) and a high yield (around 0.6) after a reduction treatment at 523 K. The effect of the presence of CO2 and H2O in the feed has also been determined.

Mesoporous mixed Nb2O5-ZrO2 catalysts for dehydration of glucose into 5-hydroxymethylfurfural

Biomass is the world’s most important renewable carbon source, whose major component, carbohydrates, can be valorized by transformation into biofuels and high value-added chemicals. Among the latter, 5-hydroxymethylfurfural (HMF), obtained by C6 carbohydrates dehydration, is a versatile and key intermediate for the production of a large spectrum of biobased chemicals. Different catalytic systems have been evaluated for HMF production, mostly based on heterogeneous catalysis as alternative to the use of conventional mineral acids [1]. Moreover, niobium oxide has shown interesting properties as acid catalyst for dehydration of sugars [2-3]. On the other hand, the high surface area and large pore size of mesoporous solids make them suitable for many catalytic processes. In the present work, the dehydration of glucose to HMF has been evaluated by using different mesoporous mixed Nb2O5-ZrO2 in a biphasic water–Methyl Isobutyl Ketone (MIBK) solvent system to avoid the HMF degradation. Different experimental parameters, such as reaction temperature and time, as well as the addition of CaCl2 have been studied in order to maximize the HMF yield.N2 adsorption-desorption isotherms have corroborated the mesostructured character of catalysts, being all isotherms of Type IV according to the IUPAC classification. BET surface area decreases for catalysts with higher Zr content (Table 1). Likewise, pore volume and average pore diameter values diminish after Zr incorporation. Concerning the acid properties, a clear correlation between Nb and acidity can be observed, in such a way that total acidity, as deduced from NH3-TPD, decreases when the Zr content rises, and consequently the amount of Nb is reduced.These mesoporous Nb-Zr catalysts have been tested in the dehydration of glucose to HMF at 175 ºC under batch operation in aqueous solution, using MIBK as co-solvent. It can be observed that both glucose conversion and HMF yield increase with the Nb content, being maximum (90% and 36%, respectively) after 90 minutes for Nb2O5. This trend changes when CaCl2 is added to the reaction medium, improving the catalytic performance of mixed oxides and ZrO2, but Nb2O5 maintains similar results than without salt addition. This could be justified by the interaction between CaCl2 and Lewis acid sites, since zirconium oxide possesses a higher amount of this acid sites type.

Laser-fused refractory oxides for optical coatings

Laser sintering was carried out using a high power continuous-wave CO2 laser to prepare pellets of zirconia (ZrO2), hafnia (HfO2) and yttria (Y2O3) mixed oxides as starting materials in the deposition of optical coatings. Hardened recrystallized pellets appeared to have been formed during laser treatment. X-ray diffraction analysis revealed a monoclinic-to-tetragonal phase transformation in the binary system while the ternary system was found to have a mixture of two crystalline phases. Cross-sectional scanning electron microscopy showed two isothermal crystalline regions in the ternary system. The optical inhomogeneity was low in the films deposited from the laser-fused pellets, but the absorption at a wavelength of 351 nm increased with increasing HfO2 content. The films deposited from laser-fused pellets were analysed by electron spectroscopy for chemical analysis and found to be stoichiometric and homogeneous.

Reactive Interdiffusion: A Method for Making Composition Graded Metal-ceramic Composites

Presented is a new method for making composition graded metal-ceramic composites using reactive inter-diffusion between a metal and a complex ceramic. Composition variation in both metal and ceramic phases with distance along the direction of diffusion is achieved. The design criteria for developing such composites are discussed. The system should exhibit extensive solid solubility in both metallic and ceramic phases, a defined gradation in the stabilities of the oxides, and mobility of electrons or holes in the oxide solid solution. The complex ceramic used for making the composite should be polycrystalline with sufficient porosity to accommodate the volume expansion caused by alloy precipitation. An inert atmosphere to prevent oxidation and high processing temperature to facilitate diffusive transport are required. The process is illustrated using the reaction couples Fe-NiTiO3, Fe-(Mg,Co)TiO3 and Fe-(Ni,Co)TiO3.

Polyvinylidene fluoride based lightweight and corrosion resistant electromagnetic shielding materials

Various NixCo1-x alloys (with x varying from 0-60 wt%, Ni: nickel, Co: cobalt) were prepared by vacuum arc melting and mixed with polyvinylidene fluoride (PVDF) to design lightweight, flexible and corrosion resistant materials that can attenuate electromagnetic radiation. The saturation magnetization scaled with the fraction of Co in the alloy. Two key properties such as high-magnetic permeability and high-electrical conductivity were targeted. While the former was achieved using a Ni-Co alloy, multiwalled carbon nanotubes (CNTs) in the composites accomplished the latter. A unique approach was adopted to prepare the composites wherein PVDF powder along with CNTs and Ni-Co flakes were made into a paste, using a solvent, followed by hot pressing. Interestingly, CNTs facilitated in uniform dispersion of the Ni-Co alloy in PVDF, as manifested from synergistic improvement in the electrical conductivity. A significant improvement in the shielding effectiveness (41 dB, >99.99% attenuation) was achieved with the addition of 50 wt% of Ni40Co60 alloy and 3 wt% CNTs. Intriguingly, due to the unique processing technique adopted here, the flexibility of the composites was retained and more interestingly, the composites were resistant to corrosion as compared to only Ni-Co alloy.

Estudo da desativação térmica de catalisadores à base de óxidos mistos de cério e zircônio

Em termos ambientais, os catalisadores automotivos se destacam pelos resultados altamente significativos alcançados após seu uso obrigatório em veículos leves. No entanto, as condições térmicas em que eles operam podem levar a um processo de perda de atividade significativa, após certo tempo de operação. Dentro desse contexto, este trabalho estudou o efeito da temperatura na desativação térmica de catalisadores automotivo modelo. Foram preparados catalisadores baseados em óxido misto de cério e zircônio na proporção 50% em mol de cério e zircônio (CZ). A partir dele foram produzidos os catalisadores Pd-CZ e Pd-CZ-LaAl. O catalisador Pd-CZ foi produzido pela impregnação do CZ com Pd na concentração de 0,5% m/m de CZ. O catalisador Pd-CZ-LaAl foi produzido a partir de uma mistura física do Pd-CZ com o suporte LaAl (alumina dopada com La na concentração de 1,9 % m/m de Al2O3), seguida de calcinação a 500˚C. Foram realizados envelhecimentos a 900C e 1200C em mufla com atmosfera oxidante por 12 e 36h. Os catalisadores foram caracterizados por um conjunto de técnicas físico-químicas. Foram realizadas análises de fisissorção de N2 para a medição da área específica e o estudo da evolução do diâmetro e volume de poros das amostras novas e envelhecidas. Análises de difração de raios X (DRX) foram feitas de forma a acompanhar possíveis transições de fases após o envelhecimento das amostras. Foi realizada análise química para validar a composição das amostras e ensaios de análise térmica para o catalisador CZ visando identificar a temperatura onde ocorre o fenômeno de segregação de fases. Realizaram-se ensaios de redução a temperatura programada (RTP) visando quantificar o consumo de hidrogênio e associá-lo à evolução da redutibilidade das amostras após o envelhecimento térmico. Finalmente, a avaliação catalítica foi realizada com base nas reações de oxidação do CO e do propano e de redução do NO pelo CO, através da obtenção de curvas de lightoff. As análises de DRX mostraram que o envelhecimento a 900C ocasionou alterações de fases da alumina, mas não foi verificada segregação de fases no CZ. Já a 1200C observou-se a referida segregação de fases, que coincide com a drástica queda na área específica das amostras, em alguns casos observando-se o colapso das propriedades texturais do catalisador. As análises de RTP mostraram que, em determinadas condições, o envelhecimento térmico promove a redutibilidade do sistema CZ e a introdução de Pd torna o catalisador mais facilmente redutível o que é evidenciado pelo deslocamento dos picos de redução para temperaturas mais baixas em comparação ao CZ puro. Os testes catalíticos mostraram que a introdução do Pd é um fator fundamental para a conversão do propano. Os catalisadores contendo Pd também converteram melhor o CO. Para os catalisadores envelhecidos a 1200C, o único resultado positivo foi no caso do Pd-CZ-LaAl que apesar deste tratamento térmico, ainda converteu o CO, propano e NO. Desta forma o catalisador Pd-CZ-LaAl apresentou resultados mais satisfatórios e isto evidencia que a mistura com LaAl melhora o desempenho e a estabilidade térmica do catalisador em altas temperaturas (acima de 300C).

Effects of magnetostriction and superlattice formation in ferromagnetic thin films

The contribution to the magnetic uniaxial perpendicular anisotropy which arises from substrate constraint through magnetostrictive effects has been measured in Ni-Fe and Ni-Co thin films evaporated on substrates at room temperature. This was accomplished by measuring the perpendicular anisotropy before and after removal of the film from the substrate. Data are given for the fcc crystal structure regions of both alloy systems, but data for Ni-Co include compositions with less than 60% Ni which have a small percentage of the hcp phase mixed with the fcc phase. The constraint contribution to the perpendicular anisotropy correlates well with the value of the bulk magnetostriction constant using the equation ∆K_˔=3/2λ_sσ. Measured values of isotropic stress for films thicker than 600 Å were 1.6 x 10¹⁰ dyn/cm². In films less than 600 Å thick the isotropic stress decreased with decreasing thickness. After removal of the films from the substrates, the measured perpendicular anisotropy deviated from the expected geometrical shape anisotropy near pure Ni in both alloys. This indicates that additional significant sources of anisotropy exist at these compositions.

The effect of substrate constraint on the crystalline anisotropy K₁ of Ni-Fe epitaxial films has been studied by use of a film removal technique, which involves the evaporation of an epitaxial layer of LiF on MgO, the epitaxial growth of the metallic film on the LiF, and the stripping of the film with water soluble tape. Films ranging in composition from 50% to 100% Ni have been studied. For compositions below 90% Ni the experimental values agree reasonably well with the first order theoretical prediction, ∆K₁=[-9/4(C₁₁-C₁₂)λ² 100+9/2C₄₄λ²111].

In order to compare the magnetic properties of epitaxial thin films more completely with the properties of bulk single crystals, Ni-Fe films ranging in composition from 60% to 90% Ni, which were evaporated epitaxially on (100) MgO substrates, have been subsequently annealed at 400°C in a vacuum of less than 10^-7 Torr to form the ordered Ni₃Fe structure near the 75% composition. This ordered structure has been confirmed by electron diffraction.

The saturation magnetization at Ni₃Fe increased about 6% with ordering which is in good agreement with previous bulk data. Measurements of the magnetocrystalline anisotropy energy K₁ for the epitaxial films show the same large changes with ordering as observed in bulk single crystal samples. In the (001) plane the magnetostriction constants ^λ100, ^λ111 are directly related to the induced anisotropy due to a uniform uniaxial strain in the [100] and [110] directions respectively. Assuming that the elastic constants of a film are the same as in bulk material and are unchanged by ordering, the changes in strain sensitivity with ordering for the epitaxial films are found to be in good agreement with values predicted from bulk data. The exchange constant A as measured by ferromagnetic resonance has been measured at the Ni₃Fe composition and found to increase 25% with ordering. This seems to indicate a significant increase in the Curie temperature which has only been inferred indirectly for bulk material.

Estudo de catalisadores modelo à base de CeO2-ZrO2 dopado com cobre para controle de emissões de NOx

Convencionalmente, metais nobres são empregados como metais ativos em catalisadores automotivos, mas o uso de cobre vem sendo estudado pelo fato de promover sítios ativos para adsorção química e redução de NOx. Diante deste contexto, esta dissertação visa testar novas formulações de catalisadores, com foco em seu desempenho na reação de redução do NO pelo CO e sua seletividade a N2. Foram avaliados o método de adição de cobre no preparo e os teores de cobre utilizados na preparação. Os métodos de adição utilizados foram impregnação a seco (IS), reação em estado sólido (RS) e coprecipitação (CO). Os teores de cobre estudados ficaram entre 0,36 e 6,9% (m/m). Além disso, foi estudado o impacto no desempenho do catalisador após envelhecimento térmico a 950C por 12h. Foram empregadas as seguintes técnicas de caracterização textural e físico-química como espectrometria de absorção atômica, fisissorção de N2, difração de raios X, espectroscopia Raman e redução a temperatura programada. Os catalisadores também foram avaliados na reação de redução do NO pelo CO. A análise textural indicou que o método de coprecipitação levou a características texturais diferentes dos outros catalisadores. Análises de DRX mostraram a formação de CuO cristalino para teores iguais ou superiores a 3,3% (m/m) de cobre. As análises de Redução a Temperatura Programada (RTP) indicaram que ocorreu uma forte interação na interface entre o suporte e as espécies de cobre dispersas, acompanhada da diminuição da temperatura de redução do CuO e da redução parcial da céria em temperaturas mais baixas. Os testes catalíticos mostraram um melhor desempenho dos catalisadores (IS) que apresentaram conversões mais elevadas em menores temperaturas. Com relação ao envelhecimento, observou-se uma diminuição significativa da eficiência dos catalisadores. Uma comparação com catalisadores à base de metal nobre mostrou um bom desempenho dos catalisadores à base de cobre, com a vantagem destes apresentarem emissão de N2O restrita a baixas temperaturas

Síntese e caracterização de TiO2 puro e modificado para aplicações ambientais

Fotocatalisadores baseados em nanopartículas de dióxido de titânio modificados fornecem soluções em potencial para a mineralização de poluentes orgânicos em meio aquoso. Agentes modificadores têm sido amplamente investigados com o objetivo de promover a fotoativação pela luz visível. Foram estudadas a nível fundamental até aqui, as modificações estruturais, texturais e óticas causadas pela introdução de silício e nitrogênio na rede da titânia. Titânias puras (TiO2) e modificadas nanoestruturadas, particularmente titânias modificadas com silício (TiO2-SiO2), com razões atômicas Si/Ti de 0,1, 0,2 e 0,3 foram sintetizadas pelo método sol-gel a partir da hidrólise ácida de isopropóxido de titânio(IV) e tetraetoxisilano. As metodolo-gias sintéticas desenvolvidas tentaram aderir aos princípios da Química Verde, dispensando o uso de atmosfera inerte e temperatura e pressão elevadas, o que foi alcançado utilizando-se, principalmente, a agitação ultrassônica. Titânias modificadas com silício e dopadas com ni-trogênio (TiO2-SiO2-N) foram obtidas a partir do pré-tratamento de TiO2-SiO2 a 500 C ao ar e então submetidas ao fluxo de amônia (NH3) a 600 C por 1-3 h e, após resfriamento, foram recozidas a 400 C ao ar. Amostras distintas foram caracterizadas, na forma de pó seco e após calcinação entre 400600 C, por difração de raios X, adsorção de nitrogênio, microscopia eletrônica de varredura e espectroscopia de refletância difusa no UV-Visível. As titânias pu-ras, obtidas principalmente variando-se a razão de hidrólise, foram cristalizadas na forma de anatásio como fase predominante até 600 C, além de traços de brookita presente até 500 C. O rutilo foi identificado a partir de 600 C como fase minoritária, embora apresentando tama-nhos de cristal significativamente maiores que os estimados para o cristal de anatásio. As titâ-nias modificadas com até 20% de silício apresentaram notável estabilidade térmica, evidenci-ada pela presença exclusiva de anatásio até 900 C. Foi também observado o aparecimento de macroporos com diâmetro médio em torno de 55 nm após calcinação a 400 C, diferentemente do que se observou nas amostras em geral. A introdução de baixo teor de silício assegurou às titânias calcinadas valores elevados de área específica, atribuído ao efeito de contenção acentuada na taxa de crescimento do cristal. As titânias modificadas com silício e as titânias puras obtidas com taxa de hidrólise 25:1 para a razão H2O : Ti apresentaram mesoporos com diâmetros médios de mesma dimensão do cristal. As titânias modificadas com silício e dopa-das com nitrogênio apresentaram absorção na região visível entre 400-480 nm, com discreta redução da energia de band gap para as transições eletrônicas consideradas. Titânias calcina-das a 300−400 C apresentaram desempenho fotocatalítico semelhante ao TiO2 P25 da De-gussa sob irradiação UV, na degradação do azo corante Reactive Yellow 145 em soluções a-quosas em pH 5 a 20 1C

Morphology observation of carbon deposition by CH4 decomposition over Ni-based catalysts

We found a novel morphology variation of carbon deposition derived from CH4 decomposition over NI-based catalysts. By altering the chemical composition and particle size of Ni-based catalysts, carbon filaments, nanofibres and nanotubes were observed over conventional Ni/y-Al2O3, Ni-Co/gamma-Al2O3 and nanoscale Ni-Co/gamma-Al2O3 catalysts, respectively. The simple introduction of Co into a conventional Ni/gamma-Al2O3 catalyst can vary the carbon deposition from amorphous filamentous carbon to ordered carbon fibres. Moreover, carbon nanotubes with uniform diameter distribution can be obtained over nanosized Ni-Co/gamma-Al2O3 catalyst particles. In addition, the oxidation behaviour of the different deposited carbon was studied by using a temperature-programmed oxidation technique. This work provides a simple strategy to control over the size and morphology of the carbon deposition from catalytic decomposition of CH4.

Structure characterization and physical properties of a complex with supramolecular architectures Co-2(2,6-DPC2Co(H2O)5 center dot 2H(2)O (DPC=2,6-pyridinedicarboxylate)

Reaction of 2,6-pyridinedicarboxylic with CoCl2 . 6H(2)O in aqueous solution give rise to a three-dimensional Complex CO2(2,6-DPC)(2)Co(H2O)(5).2H(2)O (DPC = 2,6-pyridinedicarboxylate) 1. It has been characterized by elemental analyses, infrared spectra (IR) spectrum, thermogravimetric (TG) analysis, EPR spectrum, and single crystal X-ray diffraction. The complex crystallizes in the P2(1)/c space group with a = 8.3906(3) Angstrom, b = 27.4005(8) Angstrom, c = 9.6192(4) A, alpha = 90.00degrees, beta = 98.327(2)degrees, gamma = 90.00degrees, V = 2188.20(14) Angstrom(3), Z = 4. There are two types of cobalt environments: Co(1) is coordinated by four oxygen atoms from four carboxyl groups and two nitrogen 2 atoms which are all from pdc(2). Co(2) is coordinated by six oxygen atoms, five from coordinated water molecules and one from a carboxyl of pdc(2) - of which the other oxygen atom is linked to the Co(1). The extensive intermolecular hydrogen bonds are formed in the crystal by means of the five coordinated water molecules.

Preparation and properties of polyimide films codoped with barium and titanium oxides

Polyimide hybrid films containing bimetalic compounds were obtained by codoping poly(amic acid) with a barium and titanium precursor prepared from BaCO3, Ti(OBu)(4), and lactic acid followed by casting and thermal curing. FTIR, WAXD, and XPS measurements showed that barium and titanium precursor could be transformed to BaTiO3 at a temperature above 650 degreesC, while the mixed oxides were only found in hybrid films. The measurements of TEM and AFM indicated a homogeneous distribution of inorganic phase with particle sizes less than 50 nm. The hybrid films exhibited fairly high thermal stability, good optical transparency, and promising mechanical properties. The incorporation of 10 wt % barium and titanium oxide lowered surface and volume electrical resistivity by 2 and 5 orders, respectively, increasing dielectric constant from 3.5 to 4.2 and piezoelectric constant from 3.8 to 5.2 x 10(-12) c/N, relative to the nondoped polyimide film.