A fracture criterion for the notch strength of high strength steels in the presence of hydrogen

High strength steels can suffer from a loss of ductility when exposed to hydrogen, and this may lead to sudden failure. The hydrogen is either accommodated in the lattice or is trapped at defects, such as dislocations, grain boundaries and carbides. The challenge is to identify the effect of hydrogen located at different sites upon the drop in tensile strength of a high strength steel. For this purpose, literature data on the failure stress of notched and un-notched steel bars are re-analysed; the bars were tested over a wide range of strain rates and hydrogen concentrations. The local stress state at failure has been determined by the finite element (FE) method, and the concentration of both lattice and trapped hydrogen is predicted using Oriani's theory along with the stress-driven diffusion equation. The experimental data are rationalised in terms of a postulated failure locus of peak maximum principal stress versus lattice hydrogen concentration. This failure locus is treated as a unique material property for the given steel and heat treatment condition. We conclude that the presence of lattice hydrogen increases the susceptibility to hydrogen embrittlement whereas trapped hydrogen has only a negligible effect. It is also found that the observed failure strength of hydrogen charged un-notched bars is less than the peak local stress within the notched geometries. Weakest link statistics are used to account for this stressed volume effect. © 2013 Elsevier Ltd.

The structure and electrochemical characteristics of La0.67Mg0.33 (Ni0.8Co0.1Mn0.1)(x) (x=2.5-5.0) multiphase alloys for nickel-metal hydride batteries

This paper presents results concerning structure and electrochemical characteristics of the La0.67Mg0.33 (Ni0.8Co0.1Mn0.1) (x) (x=2.5-5.0) alloy. It can be found from the result of the Rietveld analyses that the structures of the alloys change obviously with increasing x from 2.5 to 5.0. The main phase of the alloys with x=2.5-3.5 is LaMg2Ni9 phase with a PuNi3-type rhombohedral structure, but the main phase of the alloys with x=4.0-5.0 is LaNi(5)phase with a CaCu5-type hexagonal structure. Furthermore, the phase ratio, lattice parameter and cell volume of the LaMg2Ni9 phase and the LaNi5 phase change with increasing x. The electrochemical studies show that the maximum discharge capacity increases from 214.7 mAh/g (x=2.5) to 391.1 mAh/g (x=3.5) and then decreases to 238.5 mAh/g (x=5.0). As the discharge current density is 1,200 mA/g, the high rate dischargeability (HRD) increases from 51.1% (x=2.5) to 83.7% (x=3.5) and then decreases to 71.6% (x=5.0). Moreover, the exchange current density (I-0) of the alloy electrodes first increases and then decrease with increasing x from 2.5 to 5.0, which is consistent with the variation of the HRD. The cell volume reduces with increasing x in the alloys, which is detrimental to hydrogen diffusion and accordingly decreases the low-temperature dischargeability of the alloy electrodes.

General expression for probabilistic estimation of multiphase structure invariants in the case of a native protein and multiple derivatives. Application to estimates of the three-phase structure invariants

Concise probabilistic formulae with definite crystallographic implications are obtained from the distribution for eight three-phase structure invariants (3PSIs) in the case of a native protein and a heavy-atom derivative [Hauptman (1982). Acta Cryst. A38, 289-294] and from the distribution for 27 3PSIs in the case of a native and two derivatives [Fortier, Weeks & Hauptman (1984). Acta Cryst. A40, 646-651]. The main results of the probabilistic formulae for the four-phase structure invariants are presented and compared with those for the 3PSIs. The analysis directly leads to a general formula of probabilistic estimation for the n-phase structure invariants in the case of a native and m derivatives. The factors affecting the estimated accuracy of the 3PSIs are examined using the diffraction data from a moderate-sized protein. A method to estimate a set of the large-modulus invariants, each corresponding to one of the eight 3PSIs, that has the largest \Delta\ values and relatively large structure-factor moduli between the native and derivative is suggested, which remarkably improves the accuracy, and thus a phasing procedure making full use of all eight 3PSIs is proposed.

Study on corrosion of steels in marine environment by corrosion simulation device

Three kinds of steels were studied using electrically connected hanging specimen in the corrosion simulation device and offshore long scale hanging specimen. The experimental results obtained by the two methods show that the device can better reflect the offshore corrosion environment. A Ni-Cu-P steel specimen was studied through analysis of the specimen's corrosion products and corrosion types. The surface of the samples before and after the removal of the rust layer produced by these two methods were observed and compared after some experiments. The microstructure of the corrosion products under different marine environments were analyzed and compared through IR. It indicated good correlation between the electrically connected hanging specimen method and the long scale hanging specimen method.

Nicotinic acid as a nontoxic corrosion inhibitor for hot dipped Zn and Zn-Al alloy coatings on steels in diluted hydrochloric acid

The inhibition effect of nicotinic acid for corrosion of hot dipped Zn and Zn-Al alloy coatings in diluted hydrochloric acid was investigated using quantum chemistry analysis, weight loss test, electrochemical measurement, and scanning electronic microscope (SEM) analysis. Quantum chemistry calculation results showed that nicotinic acid possessed planar structure with a number of active centers, and the populations of the Mulliken charge, the highest occupied molecular orbital (HOMO), and the lowest unoccupied molecular orbital (LUMO) were found mainly focused around oxygen and nitrogen atoms, and the cyclic of the benzene as well. The results of weight loss test and electrochemical measurement indicated that inhibition efficiency (IE%) increased with inhibitor concentration, and the highest inhibition efficiency was up to 96.7%. The corrosion inhibition of these coatings was discussed in terms of blocking the electrode reaction by adsorption of the molecules at the active centers on the electrode surface. It was found that the adsorption of nicotinic acid on coating surface followed Langmuir adsorption isotherm with single molecular layer, and nicotinic acid adsorbed on the coating surface probably by chemisorption. Nicotinic acid, therefore, can act as a good nontoxic corrosion inhibitor for hot dipped Zn and Zn-Al alloy coatings in diluted hydrochloric acid solution. (c) 2007 Elsevier Ltd. All rights reserved.

Alloy elements' effect on anti-corrosion performance of low alloy steels in different sea zones

The corrosion rate of low alloy steel in different sea zones has close correlation with the content of the alloy element. From the field data of steel corrosion rates in atmospheric zone, splash zone and immersion zone, regression analysis was used to study the correlation between the corrosion rate of steels and the amount of added alloy elements. Three regression equations were obtained in different sea zones. Based on the equations, the anti-corrosion performance of the alloy elements can be deduced which can be used to screen out low alloy steel with good anti-corrosion performance. (C) 2007 Elsevier B.V. All rights reserved.

Corrosion resistance of hot-dipped zinc and zinc alloy coated sheet steels under offshore atmospheric environment

The application of hot-dipped zinc and zinc-aluminum alloy coatings were introduced. Exposure tests of the steels with these coatings were conducted in the offshore atmosphere in Qingdao and Xiamen for 12 years separately. Effects of the coating thickness, alloy composition and atmospheric environment on the corrosion performance were studied. Results of the onsite exposure tests were compared with the results of a previous indoor salt spray accelerated corrosion tests. The study supports that zinc-aluminum alloy coatings are useful in providing better corrosion resistance and can be further developed for future applications.

The human papillomavirus and cancer: a multiphase study investigating preventative behaviours in young males

Background: The Human Papillomavirus (HPV) is one of the world’s most common sexually transmitted infections, and a causative factor of oropharyngeal, anal and penile cancers in males. Worldwide, an estimated 39,000 HPV-associated cancers occur each year in men. The highest rates of HPV infection are found in adults aged 18 to 28 years. Clinical evidence indicates that use of a condom in addition to obtaining the HPV vaccine provides the greatest protection from HPV infections. Aim: To explore young men’s attitudes, beliefs, and behavioural intention in relation to receiving the HPV vaccine and using a condom correctly and consistently. Collectively, both behaviours are linked to the prevention of HPV transmission and associated infections with HPV. Method: A multi- phase study, underpinned by the Theory of Planned Behaviour, involving a qualitative belief elicitation, pilot, and quantitative cross-sectional study was conducted. A belief elicitation (n=12) phase was used to generate items to include in a newly developed research instrument. Post pilot the research instrument was utilised in a cross sectional online survey to explore the attitudes, beliefs, and behavioural intention of young men (n= 359) with regard to receiving the HPV vaccine, and using a condom correctly and consistently. Data Collection: Data collection took place over a three month time frame. Male participants were recruited from a university in Southern Ireland via a student email system, as well as posting advertisements on numerous health, social and sports websites. Sample: Three hundred and fifty nine male participants aged 18- 28 years completed the online questionnaire. Data Analysis: Data were analysed using SPSS. Descriptive, correlational, multiple and hierarchical regression analysis were performed on the indirect and direct variables of the Theory of Planned Behaviour i.e. attitude, subjective norm, perceived behavioural control, and intention. Status variables were also included in descriptive analysis and hierarchical regressions. Findings are presented through text and graphical representation. Results: Alarming sexual health statistics identified that only 44.3% of participants always used a condom, and 78.6% never used a condom for oral sex. Furthermore, findings reveal that the constructs of the Theory of Planned Behaviour adequately measure male’s attitudes, beliefs and behavioural intention with regard to both behaviours. The Theory of Planned Behaviour has assisted in identifying how social pressures play an influential role in relation to males receiving the HPV vaccine. Attitudes presented as the most significant predictor of male’s intentions to use a condom correctly and consistently. Intention to perform both behaviours was identified as moderate to high. Conclusion: This study has contributed to the field of HPV research, as it is the first piece of research to explore preventative HPV behaviours i.e. receiving the HPV vaccine, and condom use, amongst young males, utilising the Theory of Planned Behaviour. A deeper understanding of young male’s attitudes, beliefs, and behavioural intention on this topic has been achieved. Additionally, a new robust research instrument has been constructed. Findings from this study will undoubtedly help in the implementation of the HPV vaccine in Ireland, as well as influence health promotion campaigns aimed at young males, addressing the topic of condom use.

Multiphase mesh partitioning

We consider the load-balancing problems which arise from parallel scientific codes containing multiple computational phases, or loops over subsets of the data, which are separated by global synchronisation points. We motivate, derive and describe the implementation of an approach which we refer to as the multiphase mesh partitioning strategy to address such issues. The technique is tested on several examples of meshes, both real and artificial, containing multiple computational phases and it is demonstrated that our method can achieve high quality partitions where a standard mesh partitioning approach fails.

Multiphase mesh partitioning for parallel computational mechanics codes

We consider the load-balancing problems which arise from parallel scientific codes containing multiple computational phases, or loops over subsets of the data, which are separated by global synchronisation points. We motivate, derive and describe the implementation of an approach which we refer to as the multiphase mesh partitioning strategy to address such issues. The technique is tested on example meshes containing multiple computational phases and it is demonstrated that our method can achieve high quality partitions where a standard mesh partitioning approach fails.