Synthesis and thermal characterization of luminescent powers of terbium(III) with mixed ligands

This work deals with the synthesis and thermal decomposition of complexes of general formula: Ln(beta-dik)(3)L (where Ln=Tb(+3), beta-dik=4,4,4-trifluoro-1-phenyl-1,3butanedione(btfa) and L=1,10-fenantroline(phen) or 2,2-bipiridine(bipy). The powders were characterized by melting point, FTIR spectroscopy, LTV-visible, elemental analysis, scanning differential calorimeter(DSC) and thermogravimetry(TG). The TG/DSC curves were obtained simultaneously in a system DSC-TGA, under nitrogen atmosphere. The experimental conditions were: 0.83 ml.s(-1) carrier gas flow, 2.0 +/- 0.5 mg samples and 10 degrees C.min(-1) heating rate. The CHN elemental analysis of the Tb(btfa)(3)bipy and Tb(btfa)(3)phen complexes, are in good agreement with the expected values. The IR spectra evinced that the metal ion is coordinated to the ligands via C=O and C-N groups. The TG/DTG/DSC curves of the complexes show that they decompose before melting. The profiles of the thermal decomposition of the Tb(btfa)3phen and Tb(btfa)3bipy showed six and five decomposition stages, respectively. Our data suggests that the thermal stability of the complexes under investigation followed the order: Tb(btfa)(3)phen < Tb(btfa)(3)bipy.

Linear low density polyethylene (LLDPE) from ethylene using Tp(Ms)NiCl (Tp(Ms) = hydridotris(3-mesitylpyrazol-1-yl)) and CP2ZrCl2 as a tandem catalyst system

Linear low density polyethylene (LLDPE) with different branching contents were prepared from ethylene, without the addition of alpha-olefin comonomer, using a combination of catalyst precursors {Tp(Ms)}NiCl (1) (Tp(Ms) = hydridotris(3-mesitylpyrazol-1-yl)) and Cp2ZrCl2 (2) activated with MAO/TMA (1:1) in toluene at 0degreesC and by varying the nickel loading mole fraction (x(Ni)). The polymerization results showed that the turnover frequencies are strongly dependent on the x(Ni) varying from 6.6 x 10(3) to 32.1 x 10(3) mol[C2H4]/mol[Zr] h. The C-13 NMR spectra of the copolymers showed that the branch contents of the polymers increase as the x(Ni) increase in the medium promoting the production of polymers with a wide range of melting point (T-m) (C) 2004 Elsevier B.V. All rights reserved.

Seeding of PMN powders made by the Pechini method

The partial oxalate method, with the columbite route, associated with the Pechini method, was used to obtain a very fine ceramic powder at low temperature. Using this route it was possible to obtain a very reactive powder and to synthesize a lead magnesium niobate (PMN) powder with up to 100% of perovskite phase at a lower temperatures than the PbO melting point. The influence of the BaTiO3 and PbTiO3 seeds in the phase formation, along with time and temperature during the PMN calcination, was also investigated. The amount of 2% of BaTiO3 seeds promoted PMN powder formation with 100% of perovskite phase and a very narrow particle size distribution. (C) 2001 Elsevier B.V. Ltd and Techna S.r.l. All rights reserved.

Desenvolvimento de um dispositivo para obtenção de monocristais de ligas à base de cobre

This paper describes the drawing, construction and optimization of a device, which can be used to obtain single crystals of different metallic materials with melting point from 550 to 1050°C. Components of ease obtaining and of low cost were used. The device was based on the modified Bridgman technique and it was used to obtain single crystals of copper-based alloys. The temperature axial profiles and a difference less then 1% in the temperature between the wall and the center of the ceramic tube in the critical region for obtaining single crystals of good quality indicated that the oven presents a good thermal stability. Single crystals of CuZnAl and CuAlAg alloys of good quality were growth and characterized using optical microscopy and Laüe X-ray back reflection.

Effects of copper vapor laser radiation on the root canal wall of human teeth: A scanning electron microscope study

Objective: The aim of this study is to analyze the effects of copper vapor laser radiation on the radicular wall of human teeth. Materials and Methods: Immediately after the crowns of 10 human uniradicular teeth were cut along the cement-enamel junction, a chemical-surgical preparation of the radicular canals was completed. Then the roots were longitudinally sectioned to allow for irradiation of the surfaces of the dentin walls of the root canals. The hemi-roots were separated into two groups: one (control) with five hemi-roots that were not irradiated, and another (experimental) with 15 hemi-roots divided into three subgroups that were submitted to the following exposure times: 0.02,0.05, and 0.1 s. A copper vapor laser (510.6 nm) with a total average power of 6.5 W in green emission, frequency of 16.000 Hz, and pulse duration of 30 ns was used. Results: The results obtained by scanning electron microscope analysis showed the appearance of a cavity in the region of laser beam impact, with melting, recrystallization, and cracking on the edges of the dentin of the cavity due to heat diffusion. Conclusions: We determined that the copper vapor laser produces significant morphologic changes in the radicular wall of human teeth when using the parameters in this study. However, further research should be done to establish parameters that are compatible with dental structure in order to eliminate thermal damages. © Mary Ann Liebert, Inc.

Análise térmica de esparfloxacino

Sparfloxacin, a third-generation fluoroquinolone, is a potent antibacterial agent against a wide range of Gram-positive and Gram-negative organisms, for example Streptococcus pneumonias, Staphylococcus aureus (including methicillin-resistant strains), Legionella spp., Mycoplasma spp., Chlamydia spp. and Mycobacterium spp. This compound has been submitted to thermal analysis and the results are presented here. The DSC curve of sparfloxacin has an endothermic peak that indicates a melting point at 276.5 °C. The DTA curve of the sample in synthetic air shows two exothermic peaks, at 341.6 and 579.2 °C, attributed to compound decomposition. In the TG curve, the loss of mass can be seen to occur in two steps between 285.5 and 645.3 °C. The DTA curve obtained in a nitrogen atmosphere shows an exothermic peak, with decomposition of sparfloxacin at 340.0 °C; from the corresponding TG plot, the loss of mass starts at 254.4 °C.

Evaluation of the performance of α-SiAlON tool when turning Ti-6Al-4V alloy without coolant

Due to their high hardness and wear resistance, Si3N4 based ceramics are one of the most suitable cutting tool materials for machining cast iron, nickel alloys and hardened steels. However, their high degree of brittleness usually leads to inconsistent results and sudden catastrophic failures. This necessitates a process optimization when machining superalloys with Si3N4 based ceramic cutting tools. The tools are expected to withstand the heat and pressure developed when machining at higher cutting conditions because of their high hardness and melting point. This paper evaluates the performance of α-SiAlON tool in turning Ti-6Al-4V alloy at high cutting conditions, up to 250 m min-1, without coolant. Tool wear, failure modes and temperature were monitored to access the performance of the cutting tool. Test results showed that the performance of α-SiAl0N tool, in terms of tool life, at the cutting conditions investigated is relatively poor due probably to rapid notching and excessive chipping of the cutting edge. These facts are associated with adhesion and diffusion wear rate that tends to weaken the bond strength of the cutting tool.

Thermal denaturation and aggregation of hemoglobin of Glossoscolex paulistus in acid and neutral media

The thermal denaturation and aggregation of the HbGp, in the oxy- and cyanomet-forms, was investigated by DSC, AUC, DLS, optical absorption and CD, in the pH range from 5.0 to 7.0. Oxy-HbGp has a denaturation process partially reversible and dependent on the temperature. DSC melting curve is characterized by a single peak with Tc value of 333.4±0.2K for oxy-HbGp, while two peaks with Tc values of 332.2±0.1 and 338.4±0.2K are observed for cyanomet-HbGp, at pH 7.0. In acidic pH oxy- and cyanomet-HbGp are more stable showing higher Tc values and aggregation. AUC data show that, HbGp, at pH 7.0, upon denaturation, remains undissociated at 323K, presenting oligomeric dissociation at 333 (12±3% of tetramer and 88±5% of whole HbGp) and 343K (70±5% of monomer and 30±2% of trimer). DLS data show that the lag period before aggregation is dependent on the temperature and HbGp concentration. Optical absorption and CD results show that the increase of temperature leads to the oxy-HbGp oxidation and aggregation, above 331K, in acidic pH. CD data, for HbGp, present a greater thermal stability in acid medium than at neutral pH, with similar Tc values for both oxidation forms. Our data are consistent with previous studies and represents an advance in understanding the thermal stability of oligomeric HbGp structure. © 2012 Elsevier B.V.

Desenvolvimento de métodos analíticos qualitativos para a análise de darunavir comprimidos

Darunavir is a protease inhibitor used in the treatment of HIV infection. It is a pillar of the drug cocktail for patients diagnosed with the virus. Quality control in the pharmaceutical industry, to verify the content of active substance and study the physicochemical characteristics of the drug, is essential to ensure final product quality. Until now, standardized methods for the analysis of darunavir have not been available in official compendia. This justifies new research, to develop and validate analytical methods, as well as physicochemical and pharmaceutical analysis for this drug, both as a raw material and a finished product. Thus, in this study, (a) the average weight of darunavir tablets and (b) the melting point of the pure drug were determined, and the following analytical techniques were performed: (c) thin-layer chromatography, (d) ultraviolet spectroscopy, (e) infrared spectroscopy and (f) high performance liquid chromatography. By developing the above techniques, it is possible to make a qualitative assessment of the quality of darunavir tablets.

Design, synthesis and biological evaluation of new aryl thiosemicarbazone as antichagasic candidates

The present work reports on the synthesis, biological assaying and docking studies of a series of 12 aryl thiosemicarbazones, which were planned to act over two main enzymes, cruzain and trypanothione reductase. These enzymes are used as targets of trypanocidal activity in Chagas disease control with a minimal mutagenic profile. Three p-nitroaromatic thiosemicarbazones showed high activity against Trypanosoma cruzi in in vitro assays (IC50 < 57 μM), and no mutagenic profile was observed in micronucleous tests. Although the in vitro inhibition test showed that 10-μM doses of eight compounds inhibited cruzain activity, no correlation was found between cruzain inhibition and trypanocidal activity. © 2013 Elsevier Masson SAS. All rights reserved.

Optical properties of the MoO3-TiO2 particulate system and its use as a ceramic pigment

Mo-doped TiO2 powders were prepared using a dry mixture of TiO2 and MoO3 oxides with several compositions, followed by a calcination step at several temperatures. The resulting oxide system develops yellow and green tones. The XRD patterns showed only traces of MoO 3; however, EDS results, combined with TG/DTA data, confirmed the presence of molybdenum ions, suggesting that the changes in optical properties of the oxide system is due to the incorporation of Mo ions into the TiO 2 matrix, substituting Ti+4 with Mo+6 ions. The band gap decreased with increasing of MoO3 content; on the other hand, the band gap reached a maximum value at about 850°C to 910°C when plotted as a function of the calcination temperature. The glazes produced showed that the oxide system under study is a potential material for use as abinary ceramic pigment. Copyright © 2013 Taylor & Francis Group, LLC.

Antineoplásico potencial: síntese de derivado de salicilato de octila e5-fluoruracila para tratamento do câncer de pele

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise químico-farmacêutica de cefazolina sódica em pó liofilizado para solução injetável

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento e controle de qualidade de formulação cosmética contendo digluconato de clorexidina

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise químico-farmacêutica de hiclato de doxiciclina em comprimidos e de seu complexo de inclusão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)