Examining crystallographic orientation dependence of hardness of silica stishovite

We conducted nanoindentation to explore the hardness and elastic properties of silica stishovite, synthesized at high pressure and quenched to ambient conditions. A total of 10 crystallographic orientations were examined on selected grains with a maximum load of 4 or 20 mN. We observed discontinuity in the load-displacement curve (pop-in) for the [2 5 over(1, -)] and [6 2 over(1, -)] grains subjected to a maximum load of 20 mN. The single-crystal hardness at high plastic deformation is quasi-isotropic with an average of 32 ± 1 GPa, similar to the polycrystalline hardness reported earlier; the theoretical hardness determined from the experiments is about 54 ± 3 GPa. These two hardnesses suggest that stishovite is one of the hardest oxides. The measured indentation moduli are close to the predictions at low load (minor plasticity) but are considerably lower at high load (high plasticity). Both indentation hardness and modulus decrease with increasing plasticity. Our results underscore the necessity of considering the degree of plastic deformation when interpreting hardness and elastic moduli from indentation experiments. © 2007 Elsevier B.V. All rights reserved.

Influence of macroscopic residual stress fields on fatigue crack growth measurement in SiC particulate reinforced 8090 aluminium alloy

The effect of residual stresses, induced by cold water quenching, on the morphology of fatigue crack fronts has been investigated in a powder metallurgy 8090 aluminium alloy, with and without reinforcement in the form of 20 wt-%SiC particles. Residual stress measurements reveal that the surface compressive stresses developed in these materials are significantly greater than in conventional metallurgy ingot 8090, because surface yielding occurs on quenching. The yield stresses of the powder route materials are greater than those of ingot produced 8090 and hence greater surface stresses can be maintained. In fatigue, severe crack front bowing is observed in the powder formed materials as a result of the reduction of the R ratio (minimum load/maximum load) by the compressive residual stresses at the sides of the specimen, causing premature crack closure and hence reducing the local driving force for fatigue crack growth ΔKeff. This distortion of the crack fronts introduces large errors into measurements of crack growth rate and threshold values of ΔK.

Deformation microstructure under nanoindentations in Cu using 3D x-ray structural microscopy

We have used a recently developed x-ray structural microscopy technique to make nondestructive, submicron-resolution measurements of the deformation microstructure below a 100mN maximum load Berkovich nanoindent in single crystal Cu. Direct observations of plastic deformation under the indent were obtained using a ~0.5 µm polychromatic microbeam and diffracted beam depth profiling to make micron-resolution spatially-resolved x-ray Laue diffraction measurements. The local lattice rotations underneath the nanoindent were found to be heterogeneous in nature as revealed by geometrically necessary dislocation (GND) densities determined for positions along lines beneath a flat indent face and under the sharp Berkovich indent blade edges. Measurements of the local rotation-axes and misorientation-angles along these lines are discussed in terms of crystallographic slip systems.

Efeitos da terapia laser de baixa intensidade associada ao exercício aeróbio no reparo de tenotomia do tendão de aquiles de ratos diabéticos

Diabetes Mellitus (DM ) is a complex disease that requires continuous medical care for the reduction of risk factors in addition to glycemic control. The typical hyperglycemia of this disease produces glycosylation of proteins and so the consequence is the accumulation of glycosylation final products in various human tissues, among them, the tendon. The aerobic exercise (AE) and the low level laser therapy (LLLT) have been used to treat tendinopathies in individuals with or without DM. Objective: The aim of this study was to watch the effect of the LLLT and the AE, in association, in partial tenotomy of the tissue repair of the Achilles tendon (AT) of diabetic rats. Methods: 91 animals were utilized and divided in to the following groups: control group (GC), injured control group (GCL), diabetic group (GD), diabetic group LLLT (GD – TLBI), diabetic group trained (GD - EX) and diabetic group trained laser (GD-EX+TLBI). The animals were submitted to intervention with AE, using a protocol with a progressive increase of time (12 to 60 min) and speed of (4 to 9 m/min), and the LLLT (660 nm laser, 10mW, 4 J/cm², single point for 16 seconds, three times for week). It was analyzed morphological, biomechanical and molecular characteristics. For data showing normal distribution was used one-way ANOVA test and post hoc Tukey and data without normal distribution was used Mann Whitney test and post hoc Dunn's. It was accepted p <0.05 for statistical significance Results: The biomechanical tests indicated major improvement in the GC and GD-EX+TLBI groups when compared with the diabetic groups in the following variables: maximum load, strain, absorbed energy, stress, cross section area, elastic modulus and energy density (p<0.05). The analysis through molecular biology indicated that the association of aerobic exercise and LLLT generated an increase of the collagen I gene expression and modulated the expression of the MMP2 and MMP9 (p<0.05). No observed any major improvement in the morphological variable studied. Conclusion: the LLLT associated with aerobic exercise promotes and increase of the mechanical properties, in the control of collagen I gene expression and of the MMP2 and MMP9 of the diabetic rats.

Eutrofização do reservatório Engenheiro Armando Ribeiro Gonçalves, no Rio Grande do Norte: implicações para o abastecimento público e para a piscicultura intensiva em tanques-rede

This study aimed to describe the spatial and temporal patterns of variation in trophic state and its relation with the structure and dynamics of planktonic community of a large reservoir located in semi-arid tropical region of Northeast Brazil. The reservoir Armando Ribeiro Gonçalves is the biggest reservoir of the Rio Grande do Norte State and is responsible for about 53% of all surface water accumulated in the State. The samples of water and plankton were taken monthly in 10 points distributed throughout the longitudinal axis of the reservoir and over a full hydrological cycle. The samples were collected to determine concentrations of total phosphorus, total nitrogen, chlorophyll a and suspended solids (fixed and volatile) and for determining the composition and abundance of phytoplanktonic and zooplanktonic species. During the study period, the reservoir was characterized as eutrophic and there was no trend of increasing the trophic state of the reservoir in the period of drought. The concentrations of total phosphorus and suspended fixed solids decreased towards the dam while the N:P ratios increased in the same direction due to the reduction in the phosphorus concentrations and relative constancy in the nitrogen concentrations. The N:P ratios observed were indicative of greater limitation by phosphorus than by nitrogen. However, as concentrations of both nutrients were high and the water transparency was very low, with secchi depth usually lower than one meter, it seems likely that the planktonic primary production of the reservoir is more limited by the availability of light than the availability of nutrients. High nutrient concentrations coupled with low availability of light may explain the continuing dominance of filamentous cyanobacteria such as Cylindrospermopsis raciborskii in the plankton of the reservoir.These cyanobacteria are potentially toxic and pose a serious environmental problem because it compromises the water quality for public supply, recreation and fishing when present in high densities as in this study. The mesozooplankton of the reservoir was dominated by the calanoid Notodiaptomus cearensis and the cladoceran Diaphanosoma spinulosum. In general, the structure of zooplankton community seems to be particularly influenced by the spatial variation of cyanobacteria. The results of the regression analyses show that both the chlorophyll a concentrations and the cyanobacteria biovolume were more strongly correlated with the nitrogen than with phosphorus and that the water transparency was more strongly correlated with algal biomass than with other sources of turbidity. The maximum load of phosphorus to attain the maximum permissible concentration of total P in the reservoir was estimated in 63.2 tonnes P/ year. The current external P load to the reservoir is estimated in 324 tonnes P / year and must be severely reduced to improve the water quality for water supply and allow the implementation of aquaculture projects that could contribute to the socio-economic development of the region

Double incretin receptor knock-out (DIRKO) mice present with alterations of trabecular and cortical micromorphology and bone strength.

International audience

Estudo sobre as potencialidades de compósitos à base de gesso e fibras de coco seco para aplicação na construção civil

The use of gypsum, one of the oldest building materials for the construction industry in the country has been experiencing a significant and steady growth, due to its low cost and some of its properties that confer comparative advantage over other binder materials. Its use comprises various applications including the coating of walls and the production of internal seals and linings. Moreover, the fibers are being increasingly incorporated into arrays fragile in an attempt to improve the properties of the composite by reducing the number of cracks, the opening of the same and its propagation velocity. Other properties, depending on the function of the component material or construction, among these thermal and acoustic performances, are of great importance in the context of buildings and could be improved, that is, having better performance with this embodiment. Conduct a comparative study of physico-mechanical, thermal and acoustic composite gypsum incorporating dry coconut fiber, in the form of blanket, constituted the main objective of this work. Improving the thermal and acoustic performances of precast gypsum, used for lining and internal vertical fences of buildings, was the purpose of development of these composites. To evaluate the effect of fiber content on the properties of the composites were used to manufacture the composite layer with different thicknesses. The composites were fabricated in the form of plates with dimensions of 500x500x24mm. To facilitate the comparative study of the properties were also made with material gypsum boards only. We then determined the physico-mechanical, thermal and acoustical plaster and composites. The results indicated that the composites were significant gains in relation to thermal performance and also acoustic, in certain frequency range, increasing the thickness of the blanket. Concerning other physical-mechanical properties, the results showed that although the compressive strength was lower than for the composite did not occur after a fracture catastrophic failure. The same trend was observed with regard to resistance to bending, since the composites have not suffered sudden rupture and still continued after the load supporting point of maximum load

Eutrofização do reservatório Engenheiro Armando Ribeiro Gonçalves, no Rio Grande do Norte: implicações para o abastecimento público e para a piscicultura intensiva em tanques-rede

This study aimed to describe the spatial and temporal patterns of variation in trophic state and its relation with the structure and dynamics of planktonic community of a large reservoir located in semi-arid tropical region of Northeast Brazil. The reservoir Armando Ribeiro Gonçalves is the biggest reservoir of the Rio Grande do Norte State and is responsible for about 53% of all surface water accumulated in the State. The samples of water and plankton were taken monthly in 10 points distributed throughout the longitudinal axis of the reservoir and over a full hydrological cycle. The samples were collected to determine concentrations of total phosphorus, total nitrogen, chlorophyll a and suspended solids (fixed and volatile) and for determining the composition and abundance of phytoplanktonic and zooplanktonic species. During the study period, the reservoir was characterized as eutrophic and there was no trend of increasing the trophic state of the reservoir in the period of drought. The concentrations of total phosphorus and suspended fixed solids decreased towards the dam while the N:P ratios increased in the same direction due to the reduction in the phosphorus concentrations and relative constancy in the nitrogen concentrations. The N:P ratios observed were indicative of greater limitation by phosphorus than by nitrogen. However, as concentrations of both nutrients were high and the water transparency was very low, with secchi depth usually lower than one meter, it seems likely that the planktonic primary production of the reservoir is more limited by the availability of light than the availability of nutrients. High nutrient concentrations coupled with low availability of light may explain the continuing dominance of filamentous cyanobacteria such as Cylindrospermopsis raciborskii in the plankton of the reservoir.These cyanobacteria are potentially toxic and pose a serious environmental problem because it compromises the water quality for public supply, recreation and fishing when present in high densities as in this study. The mesozooplankton of the reservoir was dominated by the calanoid Notodiaptomus cearensis and the cladoceran Diaphanosoma spinulosum. In general, the structure of zooplankton community seems to be particularly influenced by the spatial variation of cyanobacteria. The results of the regression analyses show that both the chlorophyll a concentrations and the cyanobacteria biovolume were more strongly correlated with the nitrogen than with phosphorus and that the water transparency was more strongly correlated with algal biomass than with other sources of turbidity. The maximum load of phosphorus to attain the maximum permissible concentration of total P in the reservoir was estimated in 63.2 tonnes P/ year. The current external P load to the reservoir is estimated in 324 tonnes P / year and must be severely reduced to improve the water quality for water supply and allow the implementation of aquaculture projects that could contribute to the socio-economic development of the region

Influence of CAD-CAM diamond bur deterioration on surface roughness and maximum failure load of Y-TZP-based restorations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Charleston Side Channel Reservoir Total Maximum Daily Load report, Coles County, Illinois /

"IEPA/BOW/03-013"--Cover.

Load on osseointegrated fixation of a transfemoral amputee during a fall : loading, descent, impact and recovery analysis

Falling represents a health risk for lower limb amputees fitted with an osseointegrated fixation mainly because of the potential damage to the fixation. The purpose of this study was to characterise a real forward fall that occurred inadvertently to a transfemoral amputee fitted with an osseointegrated fixation while attending a gait measurement session to assess the load applied on the residuum. The objective was to analyse the load applied on the fixation with an emphasis on the sequence of events, the pattern and the magnitude of the forces and moments. The load was measured directly at 200 Hz using a six-channel transducer. Complementary video footage was also studied. The fall was divided into four phases: loading (240 ms), descent (620 ms), impact (365 ms) and recovery (2495 ms). The main impact forces and moments occurred 870 ms and 915 ms after the heel contact, and corresponded to 133 %BW and 17 %BWm, or 1.2 and 11.2 times the maximum forces and moments applied during the previous steps of the participant, respectively. This study provided key information to engineers and clinicians facing the challenge to design equipment, and rehabilitation and exercise programs to restore safely the locomotion of lower limb amputees.

A novel load transfer scheme for peak load management in rural areas

This paper proposes a novel peak load management scheme for rural areas. The scheme transfers certain customers onto local nonembedded generators during peak load periods to alleviate network under voltage problems. This paper develops and presents this system by way of a case study in Central Queensland, Australia. A methodology is presented for determining the best location for the nonembedded generators as well as the number of generators required to alleviate network problems. A control algorithm to transfer and reconnect customers is developed to ensure that the network voltage profile remains within specification under all plausible load conditions. Finally, simulations are presented to show the performance of the system over a typical maximum daily load profile with large stochastic load variations.

Statistical analyses of weigh-in-motion data for bridge live load development

This paper discusses the statistical analyses used to derive bridge live loads models for Hong Kong from a 10-year weigh-in-motion (WIM) data. The statistical concepts required and the terminologies adopted in the development of bridge live load models are introduced. This paper includes studies for representative vehicles from the large amount of WIM data in Hong Kong. Different load affecting parameters such as gross vehicle weights, axle weights, axle spacings, average daily number of trucks etc are first analyzed by various stochastic processes in order to obtain the mathematical distributions of these parameters. As a prerequisite to determine accurate bridge design loadings in Hong Kong, this study not only takes advantages of code formulation methods used internationally but also presents a new method for modelling collected WIM data using a statistical approach.

The effects of increased endurance training load on biomarkers of heat intolerance during intense exercise in the heat

The effects of increased training (IT) load on plasma concentrations of lipopolysaccharides (LPS), proinflammatory cytokines, and anti-LPS antibodies during exercise in the heat were investigated in 18 male runners, who performed 14 days of normal training (NT) or 14 days of 20% IT load in 2 equal groups. Before (trial 1) and after (trial 2) the training intervention, all subjects ran at 70% maximum oxygen uptake on a treadmill under hot (35 degrees C) and humid (similar to 40%) conditions, until core temperature reached 39.5 degrees C or volitional exhaustion. Venous blood samples were drawn before, after, and 1.5 h after exercise. Plasma LPS concentration after exercise increased by 71% (trial 1, p < 0.05) and 21% (trial 2) in the NT group and by 92% (trial 1, p < 0.01) and 199% (trial 2, p < 0.01) in the IT group. Postintervention plasma LPS concentration was 35% lower before exercise (p < 0.05) and 47% lower during recovery (p < 0.01) in the IT than in the NT group. Anti-LPS IgM concentration during recovery was 35% lower in the IT than in the NT group (p < 0.05). Plasma interleukin (IL)-6 and tumor necrosis factor (TNF)-alpha concentrations after exercise (IL-6, 3-7 times, p < 0.01, and TNF-alpha, 33%, p < 0.01) and during recovery (IL-6, 2-4 times, p < 0.05, and TNF-alpha, 30%, p < 0.01) were higher than at rest within each group. These data suggest that a short-term tolerable increase in training load may protect against developing endotoxemia during exercise in the heat.

Maximum loadability achievement in SWER networks using optimal sizing and locating of batteries

This paper presents an optimisation algorithm to maximize the loadability of single wire earth return (SWER) by minimizing the cost of batteries and regulators considering the voltage constraints and thermal limits. This algorithm, that finds the optimum location of batteries and regulators, uses hybrid discrete particle swarm optimization and mutation (DPSO + Mutation). The simulation results on realistic highly loaded SWER network show the effectiveness of using battery to improve the loadability of SWER network in a cost-effective way. In this case, while only 61% of peak load can be supplied without violating the constraints by existing network, the loadability of the network is increased to peak load by utilizing two battery sites which are located optimally. That is, in a SWER system like the studied one, each installed kVA of batteries, optimally located, supports a loadability increase as 2 kVA.