PHOTOELASTIC ANALISYS OF A HUMAN VERTEBRA MODEL WITH PEDICULAR SCREW

Introduction: The vertebrae fixation system using pedicular screws is one of the most efficient methods to treat vertebral spine pathologies. When the screw is submitted to pullout strength, it causes internal tension near the medullar canal and this situation can be analyzed by using the photoelasticity technique. Objective: Were analyzed those internal tensions near the medullar canal of photoelastic vertebra models using different sizes of screws of the vertebral fixation system submitted to pullout strength. Methods: A lumbar vertebral model made of photoelastic material with three different USS1-type pedicular screw sizes (5, 6, and 7 mm) was used. The internal tensions around the screw were tested in 12 predetermined points by a plain transmission polaroscope. Results: The areas of greater tension concentration were between the medullar canal and the curves of the transverse process. Comparing the maximum average pulling tension, statistical differences were observed between screws 5 and 7, and 6 and 7. On the other hand, for screws 5 and 6, there were no significant differences. Conclusion: The study evidenced that the internal tensions are greater in irregular areas, next to the medullar canal, showing that this is a critical region.

Newly Formed Bone in Mandible Decortication Experimental Model Using rhBMP-2 Evaluated by Densitometric Study

The purpose of this study was to evaluate the newly formed bone, comparing two different carriers for rhBMP-2, using the decortication and nondecorticatication surgical technique in Wistar rat mandibles, evaluated by radiographic densitometry method. It was used fifty six animals according to specific treatment, which were sacrificed after 3 and 6 weeks after this. It was concluded that the decortication surgical technique was able to optimize the osteoinduction properties of the rhBMP-2, independently of the material carrier used and the period of time, according to radiographic densitometry technique.

Assessment of the Expression of IR beta, IRS-1, IRS-2 and IGF-IR beta in a Rat Model of Intrauterine Growth Restriction

Objective: To investigate glomerular development and expression of insulin and insulin-like growth factor receptors in an experimental model of intrauterine growth restriction (IUGR). Material and Methods: We studied three groups of Sprague-Dawley fetuses: IUGR - restricted by ligation of the right uterine artery; C-IUGR - left horn controls, and EC - external controls (non-manipulated). Body and organs were weighed, and glomerular number and volume were analyzed. Expression of IR beta, IRS-1, IRS-2 and IGF-IR beta was analyzed in liver, intestine and kidneys by immunoblotting. Results: Organ/body weight ratios were similar. In IUGR, glomerular number and volume were increased compared to C-IUGR and EC (p < 0.001). In the IUGR liver, increases were found in IGF-IR beta compared to C-IUGR and EC; IR beta compared to EC, and IRS-2 compared to C-IUGR. However, decreases in IR beta were noted in IUGR compared to C-IUGR; IRS-1 compared to C-IUGR and EC, and IRS-2 compared to EC. In IUGR intestine, increases were detected in IR beta, IRS-1 and IGF-IR beta compared to C-IUGR and EC. In IUGR kidneys, increases were observed in IR beta and IGF-IR beta compared to C-IUGR and EC, and IRS-1 compared to EC. Decreased IRS-2 in the intestine and kidney were noticed in IUGR compared to C-IUGR and EC. Conclusion: IUGR fetuses had less glomeruli and alterations in insulin receptors, which may be associated with an increased risk of disease occurrence in adulthood. Copyright (C) 2010 S. Karger AG, Basel

Involvement of NO in the inhibitory effect of Calotropis procera latex protein fractions on leukocyte rolling, adhesion and infiltration in rat peritonitis model

Aim of the study: The latex of Calotropis procera has been used in the traditional medicinal system for the treatment of leprosy, ulcers, tumors, piles and diseases of liver, spleen, abdomen and toothache. it comprises of a non-dialyzable protein fraction (LP) that exhibits anti-inflammatory properties and a dialyzable fraction (DF) exhibiting pro-inflammatory properties. The present study was carried out to evaluate the effect of LP sub-fractions on neutrophil functions and nociception in rodent models and to elucidate the mediatory role of nitric oxide (NO). Material and methods: The LP was subjected to ion exchange chromatography and the effect of its three sub-fractions (LP(PI), LP(PII), and LP(PIII)) thus obtained was evaluated on leukocyte functions in the rat peritonitis model and on nociception in the mouse model. Results: LP sub-fractions exhibit distinct protein profile and produce a significant decrease in the carrageenan and DF induced neutrophil influx and exhibit anti-nociceptive property. The LP and its sub-fractions produced a marked reduction in the number of rolling and adherent leukocytes in the mesenteric microvasculature as revealed by intravital microscopy. The anti-inflammatory effect of LP(PI), the most potent anti-inflammatory fraction of LP, was accompanied by an increase in the serum levels of NO. Further, our study shows that NO is also involved in the inhibitory effect of LP(PI) on neutrophil influx. Conclusions: Our study shows that LP fraction of Calotropis procera comprises of three distinct sets of proteins exhibiting anti-inflammatory and anti-nociceptive properties of which LP(PI) was most potent in inhibiting neutrophil functions and its effects are mediated through NO production. (C) 2009 Elsevier Ireland Ltd. All rights reserved.

Briefing: Factored material properties and limit state loads-unlikely extreme or impossible pretense

In the limit state design (LSD) method each design criterion is formally stated and assessed using a performance function. The performance function defines the relationship between the design parameters and the design criterion. In practice, LSD involves factoring up loads and factoring down calculated strengths and material parameters. This provides a convenient way to carry out routine probabilistic-based design. The factors are statistically calculated to produce a design with an acceptably low probability of failure. Hence the ultimate load and the design material properties are mathematical concepts that have no physical interpretation. They may be physically impossible. Similarly, the appropriate analysis model is also defined by the performance function and may not describe the real behaviour at the perceived physical equivalent limit condition. These points must be understood to avoid confusion in the discussion and application of partial factor LSD methods.

Simulation of the influence of rate- and state-dependent friction on the macroscopic behavior of complex fault zones with the lattice solid model

In order to understand the earthquake nucleation process, we need to understand the effective frictional behavior of faults with complex geometry and fault gouge zones. One important aspect of this is the interaction between the friction law governing the behavior of the fault on the microscopic level and the resulting macroscopic behavior of the fault zone. Numerical simulations offer a possibility to investigate the behavior of faults on many different scales and thus provide a means to gain insight into fault zone dynamics on scales which are not accessible to laboratory experiments. Numerical experiments have been performed to investigate the influence of the geometric configuration of faults with a rate- and state-dependent friction at the particle contacts on the effective frictional behavior of these faults. The numerical experiments are designed to be similar to laboratory experiments by DIETERICH and KILGORE (1994) in which a slide-hold-slide cycle was performed between two blocks of material and the resulting peak friction was plotted vs. holding time. Simulations with a flat fault without a fault gouge have been performed to verify the implementation. These have shown close agreement with comparable laboratory experiments. The simulations performed with a fault containing fault gouge have demonstrated a strong dependence of the critical slip distance D-c on the roughness of the fault surfaces and are in qualitative agreement with laboratory experiments.

Integrating environmental and economic life cycle analysis in product development: a material selection case study

Purpose Achieving sustainability by rethinking products, services and strategies is an enormous challenge currently laid upon the economic sector, in which materials selection plays a critical role. In this context, the present work describes an environmental and economic life cycle analysis of a structural product, comparing two possible material alternatives. The product chosen is a storage tank, presently manufactured in stainless steel (SST) or in a glass fibre reinforced polymer composite (CST). The overall goal of the study is to identify environmental and economic strong and weak points related to the life cycle of the two material alternatives. The consequential win-win or trade-off situations will be identified via a Life Cycle Assessment/Life Cycle Costing (LCA/LCC) integrated model. Methods The LCA/LCC integrated model used consists in applying the LCA methodology to the product system, incorporating, in parallel, its results into the LCC study, namely those of the Life Cycle Inventory (LCI) and the Life Cycle Impact Assessment (LCIA). Results In both the SST and CST systems the most significant life cycle phase is the raw materials production, in which the most significant environmental burdens correspond to the Fossil fuels and Respiratory inorganics categories. The LCA/LCC integrated analysis shows that the CST has globally a preferable environmental and economic profile, as its impacts are lower than those of the SST in all life cycle stages. Both the internal and external costs are lower, the former resulting mainly from the composite material being significantly less expensive than stainless steel. This therefore represents a full win-win situation. As a consequence, the study clearly indicates that using a thermoset composite material to manufacture storage tanks is environmentally and economically desirable. However, it was also evident that the environmental performance of the CST could be improved by altering its End-of-Life stage. Conclusions The results of the present work provide enlightening insights into the synergies between the environmental and the economic performance of a structural product made with alternative materials. Further, they provide conclusive evidence to support the integration of environmental and economic life cycle analysis in the product development processes of a manufacturing company, or in some cases even in its procurement practices.

Multilayer Architectures Based on a-SiC:H Material: Tunable Wavelength Filters in Optical Processing Devices

The characteristics of tunable wavelength filters based on a-SiC:H multilayered stacked pin cells are studied both theoretically and experimentally. The optical transducers were produced by PECVD and tested for a proper fine tuning of the cyan and yellow fluorescent proteins emission. The active device consists of a p-i'(a-SiC:H)-n/p-i(a-Si:H)-n heterostructures sandwiched between two transparent contacts. Experimental data on spectral response analysis, current-voltage characteristics and color and transmission rate discrimination are reported. Cyan and yellow fluorescent input channels were transmitted together, each one with a specific transmission rate and different intensities. The multiplexed optical signal was analyzed by reading out, under positive and negative applied voltages, the generated photocurrents. Results show that the optimized optical transducer has the capability of combining the transient fluorescent signals onto a single output signal without losing any specificity (color and intensity). It acts as a voltage controlled optical filter: when the applied voltages are chosen appropriately the transducer can select separately the cyan and yellow channel emissions (wavelength and frequency) and also to quantify their relative intensities. A theoretical analysis supported by a numerical simulation is presented.

A Communication Intervention for Training Southern European Oncologists to Recognize Psychosocial Morbidity in Cancer. I - Development of the Model and Preliminary Results on Physicians' Satisfaction

BACKGROUND: The detection of psychosocial distress is a significant communication problem in Southern Europe and other countries. Work in this area is hampered by a lack of data. Because not much is known about training aimed at improving the recognition of psychosocial disorders in cancer patients, we developed a basic course model for medical oncology professionals. METHODS: A specific educational and experiential model (12 hours divided into 2 modules) involving formal teaching (ie, journal articles, large-group presentations), practice in small groups (ie, small-group exercises and role playing), and discussion in large groups was developed with the aim of improving the ability of oncologists to detect emotional disturbances in cancer patients (ie, depression, anxiety, and adjustment disorders). RESULTS: A total of 30 oncologists from 3 Southern European countries (Italy, Portugal, and Spain) participated in the workshop. The training course was well accepted by most participants who expressed general satisfaction and a positive subjective perception of the utility of the course for clinical practice. Of the total participants, 28 physicians (93.3%) thought that had they been exposed to this material sooner, they would have incorporated the techniques received in the workshop into their practices; 2 participants stated they would likely have done so. Half of the doctors (n = 15) believed that their clinical communication techniques were improved by participating in the workshop, and the remaining half thought that their abilities to communicate with cancer patients had improved. CONCLUSIONS: This model is a feasible approach for oncologists and is easily applicable to various oncology settings. Further studies will demonstrate the effectiveness of this method for improving oncologists skills in recognizing emotional disorders in their patients with cancer.

HCV INFECTION THROUGH PERFORATING AND CUTTING MATERIAL AMONG CANDIDATES FOR BLOOD DONATION IN BELÉM, BRAZILIAN AMAZON

This study evaluated epidemiological factors for HCV infection associated with sharing perforating and cutting instruments among candidates for blood donation (CBD) in the city of Belém, Pará, Brazilian Amazon. Two definitions of HCV infection cases were used: anti-HCV positivity shown by EIA, and HCV-RNA detection by PCR. Infected and uninfected CBD completed a questionnaire about possible risk factors associated with sharing perforating and cutting instruments. The information was evaluated using simple and multiple logistic regressions. Between May and November 2010, 146 (1.1%) persons with anti-HCV antibodies and 106 (0.8%) with HCV-RNA were detected among 13,772 CBD in Belém. Risk factors associated with HCV infection based on the EIA (model 1) and PCR (model 2) results were: use of needles and syringes sterilized at home; shared use of razors at home, sharing of disposable razors in barbershops, beauty salons etc.; and sharing manicure and pedicure material. The models of HCV infection associated with sharing perforating and cutting instruments should be taken into account by local and regional health authorities and by those of other countries with similar cultural practices, in order to provide useful information to guide political and public strategies to control HCV transmission.

Optimal Cut-Off Value for Homeostasis Model Assessment (HOMA) Index of Insulin-Resistance in a Population of Patients Admitted Electively in a Portuguese Cardiology Ward

INTRODUCTION: Insulin resistance is the pathophysiological key to explain metabolic syndrome. Although clearly useful, the Homeostasis Model Assessment index (an insulin resistance measurement) hasn't been systematically applied in clinical practice. One of the main reasons is the discrepancy in cut-off values reported in different populations. We sought to evaluate in a Portuguese population the ideal cut-off for Homeostasis Model Assessment index and assess its relationship with metabolic syndrome. MATERIAL AND METHODS: We selected a cohort of individuals admitted electively in a Cardiology ward with a BMI < 25 Kg/m2 and no abnormalities in glucose metabolism (fasting plasma glucose < 100 mg/dL and no diabetes). The 90th percentile of the Homeostasis Model Assessment index distribution was used to obtain the ideal cut-off for insulin resistance. We also selected a validation cohort of 300 individuals (no exclusion criteria applied). RESULTS: From 7 000 individuals, and after the exclusion criteria, there were left 1 784 individuals. The 90th percentile for Homeostasis Model Assessment index was 2.33. In the validation cohort, applying that cut-off, we have 49.3% of individuals with insulin resistance. However, only 69.9% of the metabolic syndrome patients had insulin resistance according to that cut-off. By ROC curve analysis, the ideal cut-off for metabolic syndrome is 2.41. Homeostasis Model Assessment index correlated with BMI (r = 0.371, p < 0.001) and is an independent predictor of the presence of metabolic syndrome (OR 19.4, 95% CI 6.6 - 57.2, p < 0.001). DISCUSSION: Our study showed that in a Portuguese population of patients admitted electively in a Cardiology ward, 2.33 is the Homeostasis Model Assessment index cut-off for insulin resistance and 2.41 for metabolic syndrome. CONCLUSION: Homeostasis Model Assessment index is directly correlated with BMI and is an independent predictor of metabolic syndrome.

An experimental model for the transplantation of fetal central nervous system cells to the injured spinal cord in rats

INTRODUCTION: Traumatic spinal cord injury is one of the most disabling conditions occurring in man and thus stimulates a strong interest in its histopathological, biochemical, and functional changes, primarily as we search for preventive and therapeutic methods. PURPOSE: To develop an experimental model for transplantation of cells from the fetal rat central nervous system to the site of an injured spinal cord of an adult rat in which the transplanted cells survive and become integrated. This experimental model will facilitate investigations of factors that promote regeneration and functional recovery after spinal cord trauma. MATERIAL AND METHODS: Fifteen adult Wistar rats underwent laminectomy, and an spinal cord lesion was made with microdissection. Fetal spinal cord tissue was then transplanted to the site of the injury. The rats were monitored over a 48-hour period, and then their vertebral column was completely removed for histological analysis. RESULTS: In 60% of transplanted rats, the fetal tissue at the injured site remained viable in the site of the lesion.

Plastic-damage smeared crack model to simulate the behaviour of structures made by cement based materials

This work proposes a constitutive model to simulate nonlinear behaviour of cement based materials subjected to different loading paths. The model incorporates a multidirectional fixed smeared crack approach to simulate crack initiation and propagation, whereas the inelastic behaviour of material between cracks is treated by a numerical strategy that combines plasticity and damage theories. For capturing more realistically the shear stress transfer between the crack surfaces, a softening diagram is assumed for modelling the crack shear stress versus crack shear strain. The plastic damage model is based on the yield function, flow rule and evolution law for hardening variable, and includes an explicit isotropic damage law to simulate the stiffness degradation and the softening behaviour of cement based materials in compression. This model was implemented into the FEMIX computer program, and experimental tests at material scale were simulated to appraise the predictive performance of this constitutive model. The applicability of the model for simulating the behaviour of reinforced concrete shear wall panels submitted to biaxial loading conditions, and RC beams failing in shear is investigated.

Para um (novo) modelo de intervenção penal na União Europeia: uma reflexão a partir do princípio de legalidade como limite material de atuação da Procuradoria Europeia

Tese de Doutoramento em Ciências Jurídicas (área de especialização em Ciências Jurídicas - Públicas)

A high order model for piezoelectric rods: an asymptotic approach

Preprint submitted to International Journal of Solids and Structures. ISSN 0020-7683