Dynamic effect of high speed railway traffic loads on the ballast track settlement

The traditional ballast track structures are still being used in high speed railways lines with success, however technical problems or performance features have led to non-ballast track solution in some cases. A considerable maintenance work is needed for ballasted tracks due to the track deterioration. Therefore it is very important to understand the mechanism of track deterioration and to predict the track settlement or track irregularity growth rate in order to reduce track maintenance costs and enable new track structures to be designed. The objective of this work is to develop the most adequate and efficient models for calculation of dynamic traffic load effects on railways track infrastructure, and then evaluate the dynamic effect on the ballast track settlement, using a ballast track settlement prediction model, which consists of the vehicle/track dynamic model previously selected and a track settlement law. The calculations are based on dynamic finite element models with direct time integration, contact between wheel and rail and interaction with railway cars. A initial irregularity profile is used in the prediction model. The track settlement law is considered to be a function of number of loading cycles and the magnitude of the loading, which represents the long-term behavior of ballast settlement. The results obtained include the track irregularity growth and the contact force in the final interaction of numerical simulation

Dynamic Analysis of high Speed Railway Traffic Loads on Ballasted Track

This paper reports the studies carried out to develop and calibrate the optimal models for the objectives of this work. In particular, quarter bogie model for vehicle, rail-wheel contact with Lagrangian multiplier method, 2D spatial discretization were selected as the optimal decisions. Furthermore, the 3D model of coupled vehicle-track also has been developed to contrast the results obtained in the 2D model. The calculations were carried out in the time domain and envelopes of relevant results were obtained for several track profiles and speed ranges. Distributed elevation irregularities were generated based on power spectral density (PSD) distributions. The results obtained include the wheel-rail contact forces, forces transmitted to the bogie by primary suspension. The latter loads are relevant for the purpose of evaluating the performance of the infrastructure

Validation of the SenseWear armband in circuit resistance training with different loads

The use of the SenseWear™ armband (SWA), an objective monitor of physical activity, is a relatively new device used by researchers to measure energy expenditure. These monitors are practical, relatively inexpensive and easy-to-use. The aim of the present study was to assess the validity of SWAs for the measurement of energy expenditure (EE) in circuit resistance training (CRT) at three different intensities in moderately active, healthy subjects. The study subjects (17 females, 12 males) undertook CRT at 30, 50 and 70% of the 15 repetition maximum for each exercise component wearing an SWA as well as an Oxycon Mobile (OM) portable metabolic system (a gold standard method for measuring EE). The EE rose as exercise intensity increased, but was underestimated by the SWAs. For women, Bland-Altman plots showed a bias of 1.13 ± 1.48 METs and 32.1 ± 34.0 kcal in favour of the OM system, while for men values of 2.33 ± 1.82 METs and 75.8 ± 50.8 kcal were recorded.

Discernment of bee pollen loads using computer vision and one-class classification techniques

In this paper, we propose a system for authenticating local bee pollen against fraudulent samples using image processing and classification techniques. Our system is based on the colour properties of bee pollen loads and the use of one-class classifiers to reject unknown pollen samples. The latter classification techniques allow us to tackle the major difficulty of the problem, the existence of many possible fraudulent pollen types. Also presented is a multi-classifier model with an ambiguity discovery process to fuse the output of the one-class classifiers. The method is validated by authenticating Spanish bee pollen types, the overall accuracy of the final system of being 94%. Therefore, the system is able to rapidly reject the non-local pollen samples with inexpensive hardware and without the need to send the product to the laboratory.

On the flexural vibration of cylinders under axial loads:Numerical and experimental study

The flexural vibration of a homogeneous isotropic linearly elastic cylinder of any aspect ratio is analysed in this paper. Natural frequencies of a cylinder under uniformly distributed axial loads acting on its bases are calculated numerically by the Ritz method with terms of power series in the coordinate directions as approximating functions. The effect of axial loads on the flexural vibration cannot be described by applying infinitesimal strain theory, therefore, geometrically nonlinear strain–displacement relations with second-order terms are considered here. The natural frequencies of free–free, clamped–clamped, and sliding–sliding cylinders subjected to axial loads are calculated using the proposed three-dimensional Ritz approach and are compared with those obtained with the finite element method and the Bernoulli–Euler theory. Different experiments with cylinders axially compressed by a hydraulic press are carried out and the experimental results for the lowest flexural frequency are compared with the numerical results. An approach based on the Ritz formulation is proposed for the flexural vibration of a cylinder between the platens of the press with constraints varying with the intensity of the compression. The results show that for low compressions the cylinder behaves similarly to a sliding–sliding cylinder, whereas for high compressions the cylinder vibrates as a clamped–clamped one.

Induced shock loads during the separation of the Ariane 5 VEB structure

Tests used to simulate the separation of the lower stage of the Ariane Vehicle Equipment Bay (VEB) were carried out on a flat full scale model. Theoretical studies carried out prior to testing are described. Three different mathematical methods, finite element, component element, and wave propagation, were used. Comparison of the predicted theoretical results with the actual test results is planned.

Moving loads on railway bridges: The Spanish Code approach

This paper presents the results of part of the research carried out by a committee in charge of the elaboration of the new Spanish Code of Actions in Railway Bridges. Following the work developed by the European Rail Research Institute (ERRI), the dynamic effects caused by the Spanish high-speed train TALGO have been studied and compared with other European trains. A simplified envelope of the impact coefficient is also presented. Finally, the train-bridge interactions has been analysed and the results compared with those obtained from simple models based on moving loads.

Análisis de la influencia de los diferentes parámetros de diseño en la aparición de fatiga superficial en contactos mecánicos

La fatiga superficial es uno de los principales problemas en las transmisiones mecánicas y es uno de los focos de atención de las investigaciones de los últimos anos en Tribología. La disminución de viscosidad de los lubricantes para la mejora de la eficiencia, el aumento de las potencias a transmitir, el aumento de la vida de los componentes o la mejora de su fiabilidad han supuesto que los fenómenos de fatiga superficial hayan cobrado especial relevancia, especialmente los fenómenos de pitting y micropitting en cajas multiplicadoras/reductoras de grandes potencias de aplicación, por ejemplo, en el sector eólico. Como todo fenómeno de fatiga, el pitting y micropitting son debidos a la aplicación de cargas ciclicas. Su aparición depende de las presiones y tensiones cortantes en el contacto entre dos superficies que al encontrarse en rodadura y deslizamiento varian con el tiempo. La principal consecuencia de la fatiga superficial es la aparición de hoyuelos de diferente magnitud segun la escala del fenómeno (pitting o micropitting) en la superficie del material. La aparición de estos hoyuelos provoca la perdida de material, induce vibraciones y sobrecargas en el elemento que finalmente acaba fallando. Debido a la influencia de la presión y tensión cortante en el contacto, la aparición de fatiga depende fuertemente del lubricante que se encuentre entre las dos superficies y de las condiciones de funcionamiento en las cuales este trabajando. Cuando el contacto trabaja en condiciones de lubricacion mixta-elastohidrodinamica tiende a aparecer micropitting debido a las altas tensiones localizadas en las proximidades de las asperezas, mientras que si el régimen es de lubricación completa el tipo de fatiga superficial suele ser pitting debido a las tensiones mas suavizadas y menos concentradas. En esta Tesis Doctoral se han analizado todos estos factores de influencia que controlan el pitting y el micropitting prestando especial atención al efecto del lubricante. Para ello, se ha dado un enfoque conjunto a ambos fenómenos resolviendo las ecuaciones involucradas en el contacto elastohidrodinamico no-Newtoniano (la ecuación de Reynolds, la deformación elástica de los sólidos y la reologia del lubricante) para conocer la presión y la tensión cortante en el contacto. Conocidas estas, se resuelve el campo de tensiones en el interior del material y, finalmente, se aplican criterios de fatiga multiaxial (Crossland, Dang Van y Liu-Mahadevan) para conocer si el material falla o no falla. Con la metodología desarrollada se ha analizado el efecto sobre las tensiones y la aparición de la fatiga superficial del coeficiente viscosidad-presion, de la compresibilidad, del espesor especifico de película y de la fricción así como de la influencia de las propiedades a fatiga del material y de las condiciones de funcionamiento (radios de contacto, velocidad, deslizamiento, carga y temperatura). Para la validación de los resultados se han utilizado resultados teóricos y experimentales de otros autores junto con normas internacionales de amplia utilización en el mundo industrial, entre otras, para el diseño y calculo de engranajes. A parte del trabajo realizado por simulación y cálculo de los diferentes modelos desarrollados, se ha realizado un importante trabajo experimental que ha servido no solo para validar la herramienta desarrollada sino que además ha permitido incorporar al estudio factores no considerados en los modelos, como los aditivos del lubricante. Se han realizado ensayos de medida del coeficiente de fricción en una maquina de ensayo puntual con la que se ha validado el cálculo del coeficiente de fricción y se ha desarrollado un proceso de mejora del coeficiente de fricción mediante texturizado superficial en contactos puntuales elastohidrodinamicos mediante fotolitografia y ataque quimico. Junto con los ensayos de medida de fricción en contacto puntual se han realizado ensayos de fricción y fatiga superficial en contacto lineal mediante una maquina de discos que ha permitido evaluar la influencia de diferentes aditivos (modificadores de fricción, antidesgaste y extrema-presion) en la aparición de fatiga superficial (pitting y micropitting) y la fricción en el contacto. Abstract Surface fatigue is one of the most important problems of mechanical transmissions and therefore has been one of the main research topics on Tribology during the last years. On the one hand, industrial demand on fuel economy has led to reduce lubricant viscosity in order to improve efficiency. On the other hand, the requirements of power and life of machine elements are continuously increasing, together with the improvements in reliability. As a consequence, surface fatigue phenomena have become critical in machinery, in particular pitting and micropitting in high power gearboxes of every kind of machines, e.g., wind turbines or cranes. In line with every fatigue phenomena, pitting and micropitting are caused by cyclic loads. Their appearance depends on the evolution of pressures and shear stresses with time, throughout the contact between surfaces under rolling and sliding conditions. The main consequence of surface fatigue is the appearance of pits on the surface. The size of the pits is related to the scale of the fatigue: pitting or micropitting. These pits cause material loss, vibrations and overloads until the final failure is reached. Due to the great influence of the pressures and shear stresses in surface fatigue, the appearance of pits depends directly on the lubricant and the operating conditions. When the contact works under mixed regime (or under elastohydrodynamic but close to mixed regime) the main fatigue failure is micropitting because of the high pressures located near the asperities. In contrast, when the contact works under elastohydrodynamic fully flooded conditions the typical fatigue failure is pitting. In this Ph.D. Thesis, the main factors with influence on pitting and micropitting phenomena are analyzed, with special attention to the effect of the lubricant. For this purpose, pitting and micropitting are studied together by solving the equations involved in the non-Newtonian elastohydrodynamic contact. Thus, pressure and shear stress distributions are found by taking into account Reynolds equation, elastic deflection of the solids and lubricant rheology. Subsequently, the stress field inside the material can be calculated and different multiaxial fatigue criteria (Crossland, Dang Van and Liu- Mahadevan) can be applied to predict whether fatigue failure is reached. The influences of the main parameters on pressure and surface fatigue have been studied, taking into account the lubricant compressibility and its viscosity-pressure coefficient, the specific film thickness, the friction coefficient and the fatigue properties of the contacting materials, together with the operating conditions (contact radius, mean velocity, sliding velocity, load and temperature). Several theoretical and experimental studies of different authors have been used to validate all the results obtained, together with international standards used worldwide in gear design industry. Moreover, an experimental stage has been carried out in order to validate the calculation methods and introduce additional influences not included previously, e.g., lubricant additives. The experimentation includes different friction tests in point contacts performed with a tribological equipment in order to validate the results given by the calculations. Furthermore, the reduction and optimization of the friction coefficient is analyzed by means of textured surfaces, obtained combining photolithography and chemical etching techniques. Besides the friction tests with point contact, friction and surface fatigue tests have also been performed with line contact in a tribological test rig. This equipment is also used to study the influence of different types of additives (friction modifiers, anti-wear and extreme-pressure additives) on surface fatigue (pitting and micropitting).

Experimental investigation of dynamic pressure loads during dam break

The objectives of this work are to revisit the experimental measurements on dam break flow over a dry horizontal bed and to provide a detailed insight into the dynamics of the dam break wave impacting a vertical wall downstream the dam, with emphasis on the pressure loads. The measured data are statistically analyzed and critically discussed. As a result, an extensive set of data for validation of computational tools is provided.

Vibrations loads in the process of designing scientific spacecraft payloads

Scientific missions constitute fundamental cornerstones of space agencies such as ESA and NASA. Modern astronomy could not be understood without the data provided by these missions. Scientists need to design very carefully onboard instruments. Payloads have to survive the crucial launch moment and later perform well in the really harsh space environ-ment. It is very important that the instrument conceptual idea can be engineered to sustain all those loads

Measurements and Prediction of Pedestrian Walking Loads on an Aluminium Catwalk

During the last two decades the topic of human induced vibration has attracted a lot of attention among civil engineering practitioners and academics alike. Usually this type of problem may be encountered in pedestrian footbridges or floors of paperless offices. Slender designs are becoming increasingly popular, and as a consequence, the importance of paying attention to vibration serviceability also increases. This paper resumes the results obtained from measurements taken at different points of an aluminium catwalk which is 6 m in length by 0.6 m in width. Measurements were carried out when subjecting the structure to different actions:1)Static test: a steel cylinder of 35 kg was placed in the middle of the catwalk; 2)Dynamic test: this test consists of exciting the structure with singles impulses; 3)Dynamic test: people walking on the catwalk. Identification of the mechanical properties of the structure is an achievement of the paper. Indirect methods were used to estimate properties including the support stiffness, the beam bending stiffness, the mass of the structure (using Rayleigh method and iterative matrix method), the natural frequency (using the time domain and frequency domain analysis) and the damping ratio (by calculating the logarithmic decrement). Experimental results and numerical predictions for the response of an aluminium catwalk subjected to walking loads have been compared. The damping of this light weight structure depends on the amplitude of vibration which complicates the tuning of a structural model. In the light of the results obtained it seems that the used walking load model is not appropriate as the predicted transient vibration values (TTVs) are much higher than the measured ones.

Discussion of “Initial Pore Pressure from Vertical Surface Loads” by Jacobo Bielak (September, 1982)

The author presents a very interesting application of the ideas developed by Scott to determine the initial pore pressure in excess of the hydrostatic pore pressure in linear, elastic, homogeneous and isotropic soil-skeleton. Scott demonstrates that under vertical surface loads the problem is governed by Laplace's equation. Nevertheless the writers' think that it could be interesting to state clearly the conditions under which this analogy can be applied.

Wind tunnel analysis on the influence of cantilever parapets on the wind loads on curved roofs

Different methods to reduce the high suction caused by conical vortices have been reported in the literature: vertical parapets, either solids or porous, placed at the roof edges being the most analysed configuration. Another method for alleviating the high suction peaks due to conical vortices is to round the roof edges. Very recently, the use of some non-standard parapet configurations, like cantilever parapets, has been suggested. In this paper, its efficiency to reduce suction loads on curved roofs is experimentally checked by testing the pressure distribution on the curved roof of a low-rise building model in a wind tunnel. Very high suction loads have been measured on this model, the magnitude of these high suction loads being significantly decreased when cantilever...

Wind-induced loads over double cantilever bridges under construction

Within the last century the interest in wind-induced loads over civil engineering structures has become more and more important, the reason being that the development of new construction techniques and materials has allowed engineers and architects to design new structures far from the traditional concepts, and in many cases wind actions over these singular structures are not included in the existing codes of practice. In this paper the windinduced static loads over bridges constructed by the double cantilever method during erection stages are considered. The aerodynamic load over a double cantilever bridge under a yawing-angled wind produces a yawing (torsional) moment on the bridge deck, which can lead to undesirable rotation of the deck about the supporting pier. The effects of the wind yaw angle and the length of the deck are analysed. The wind action caused by the presence of sliding concrete forms at the ends of the deck is also studied.

Effects of traffic loads on reinforced concrete railroad culverts

In the context of the present conference paper culverts are defined as an opening or conduit passing through an embankment usually for the purpose of conveying water or providing safe pedestrian and animal crossings under rail infrastructure. The clear opening of culverts may reach values of up to 12m however, values around 3m are encountered much more frequently. Depending on the topography, the number of culverts is about 10 times that of bridges. In spite of this, their dynamic behavior has received far less attention than that of bridges. The fundamental frequency of culverts is considerably higher than that of bridges even in the case of short span bridges. As the operational speed of modern high-speed passenger rail systems rises, higher frequencies are excited and thus more energy is encountered in frequency bands where the fundamental frequency of box culverts is located. Many research efforts have been spent on the subject of ballast instability due to bridge resonance, since it was first observed when high-speed trains were introduced to the Paris/Lyon rail line. To prevent this phenomenon from occurring, design codes establish a limit value for the vertical deck acceleration. Obviously one needs some sort of numerical model in order to estimate this acceleration level and at that point things get quite complicated. Not only acceleration but also displacement values are of interest e.g. to estimate the impact factor. According to design manuals the structural design should consider the depth of cover, trench width and condition, bedding type, backfill material, and compaction. The same applies to the numerical model however, the question is: What type of model is appropriate for this job? A 3D model including the embankment and an important part of the soil underneath the culvert is computationally very expensive and hard to justify taking into account the associated costs. Consequently, there is a clear need for simplified models and design rules in order to achieve reasonable costs. This paper will describe the results obtained from a 2D finite element model which has been calibrated by means of a 3D model and experimental data obtained at culverts that belong to the high-speed railway line that links the two towns of Segovia and Valladolid in Spain