The impact of dry matter, ripeness and internal defects on consumer perceptions of avocado quality and intentions to purchase.

Insights into the relative importance of various aspects of product quality can be provided through quantitative analysis of consumer preference and choice of fruit. In this study, methods previously used to establish taste preferences for kiwifruit (Harker et al., 2008) and conjoint approaches were used to determine the influence of three key aspects of avocado quality on consumer liking and willingness to purchase fruit: dry matter percentage (DM), level of ripeness (firmness) and internal defects (bruising). One hundred and seven consumers tasted avocados with a range of DM levels from ~20% (minimally mature) to nearly 40% (very mature), and at a range of fruit firmness (ripeness) stages (firm-ripe to soft-ripe). Responses to bruising, a common quality defect in fruit obtained from the retail shelf, were examined using a conjoint approach in which consumers were presented with photographs showing fruit affected by damage of varying severity. In terms of DM, consumers showed a progressive increase in liking and intent to buy avocados as the DM increased. In terms of ripeness, liking and purchase intent was higher in avocados that had softened to a firmness of 6.5 N or below (hand-rating 5). For internal defects, conjoint analysis revealed that price, level of bruising and incidence of bruising all significantly lowered consumers' future purchase decision, but the latter two factors had a greater impact than price. These results indicate the usefulness of the methodology, and also provide realistic targets for Hass avocado quality on the retail shelf.

Resin defect impacts on the value of graded recovery and evaluation of technologies for internal defect detection in slash pine logs.

The key outcome will be to identify a technology that is practical to use to scan logs identified by the modelling as suspect or marginal for sawing and to confirm their unsuitability for value adding sawing by internal scanning.

Fractional power dependence of rate on activation energy for reactions with very low internal barriers

The dynamics of reactions with low internal barriers are studied both analytically and numerically for two different models. Exact expressions for the average rate,kI, are obtained by solving the associated first passage time problems. Both the average rate constant, kI, and the numerically calculated long-time rate constant, kL, show a fractional power law dependence on the barrier height for very low barriers. The crossover of the reaction dynamics from low to high barrier is investigated.

Electrode kinetics of a nickel/cadmium cell and failure-mode prediction. Estimation of equivalent resistance of an internal short

A quantitative expression has been obtained for the equivalent resistance of an internal short in rechargeable cells under constant voltage charging.

Nuclear Magnetic-Resonance Spectra Of Oriented Biologically Important Molecules - The Structure Of And The Internal-Rotation In N,N-Dimethyluracil

From the proton NMR spectra of Nfl-dimethyluracil oriented in two different nematic solvents, the internal rotation of the methyl groups about the N-C bonds is studied. It has been observed that the preferred conformation of the methyl group having one carbonyl in the vicinity is the one where a C-H bond is in the ring plane pointing toward the carbonyl group. The results are not sensitive to the mode of rotation of the other methyl group. These data are interpreted in terms of the bond polarizations.

Study of internal motions through N.Q.R. in 6-Chloropyridin-2-ol

Chlorine-35 n.q.r, has been observed for the first time in 6-chloropyridin-2-ol and its temperature dependence has been studied from 77 K to room temperature. The torsional frequencies and their temperature dependences have been calculated by using Bayer's theory with and without Tatsuzaki's modification.

Mechanical testing of internal fixation devices: A theoretical and practical examination of current methods

Successful healing of long bone fractures is dependent on the mechanical environment created within the fracture, which in turn is dependent on the fixation strategy. Recent literature reports have suggested that locked plating devices are too stiff to reliably promote healing. However, in vitro testing of these devices has been inconsistent in both method of constraint and reported outcomes, making comparisons between studies and the assessment of construct stiffness problematic. Each of the methods previously used in the literature were assessed for their effect on the bending of the sample and concordant stiffness. The choice of outcome measures used in in vitro fracture studies was also assessed. Mechanical testing was conducted on seven hole locked plated constructs in each method for comparison. Based on the assessment of each method the use of spherical bearings, ball joints or similar is suggested at both ends of the sample. The use of near and far cortex movement was found to be more comprehensive and more accurate than traditional centrally calculated inter fragmentary movement values; stiffness was found to be highly susceptible to the accuracy of deformation measurements and constraint method, and should only be used as a within study comparison method. The reported stiffness values of locked plate constructs from in vitro mechanical testing is highly susceptible to testing constraints and output measures, with many standard techniques overestimating the stiffness of the construct. This raises the need for further investigation into the actual mechanical behaviour within the fracture gap of these devices.

Analysis and computation of the oil film thickness between the piston ring and cylinder liner of an internal combustion engine

A study of the essential features of piston rings in the cylinder liner of an internal combustion engine reveals that the lubrication problem posed by it is basically that of a slider bearing. According to steady-flow-hydrodynamics, viz. Image the oil film thickness becomes zero at the dead centre positions as the velocity, U = 0. In practice, however, such a phenomenon cannot be supported by consideration of the wear rates of pistion rings and cylinder liners. This can be explained by including the “squeeze” action term in the

Conformation of the LL and LD hairpin bends with internal hydrogen bonds in proteins and peptides

The conformation of three linked peptide units having an internal 4 → 1 type of hydrogen bond has been studied in detail, and the low energy conformations are listed. These conformations all lead to the reversal of the chain direction, and may therefore be called as “hairpin bends” or “U-bends”. Since this bend can occur at the end of two chains hydrogen-bonded in the antiparallel β-conformation, it is also known as the “β-bend”. Two types of conformation are possible when the residues at the second and third Cα atoms are both of type L (the LL bend), while only one type is possible for the LD and the DL bend. The LL bend can also accommodate the sequences LG, GL, GG (G = glycine), while the LD bend can accommodate the sequences LG, GD and GG. The conformations for the sequences DD and DL are exact inverses (or mirror images) of those for the sequences LL and LD, respectively, and have dihedral angles (phi2, ψ2), (phi3, ψ3) of the same magnitudes, but of opposite signs as those for the former types, which are listed, along with the characteristics (length, angle and energy) of the hydrogen bonds. A comparison of the theoretical predictions with experimental data (from X-ray diffraction and NMR studies) on proteins and peptides, show reasonably good agreement. However, a systematic trend is observable in the experimental data, slightly deviating from theory, which indicates that some deformations occur in the shapes of the peptide units forming the bend, differing from that of the standard planar peptide unit.

The effect of internal audit function quality and internal audit contribution to external audit on audit fees

Corporate governance mandates and listing rules identify internal audit functions (IAF) as a central internal control mechanism. External audits are expected to assess the quality of IAF before placing reliance on its work. We provide evidence on the effect of IAF quality and IAF contribution to external audit on audit fees. Using data from a matched survey of both external and internal audits, we extend prior research which is based mainly on internal audits' assessment and conducted predominantly in highly developed markets. We find a positive relationship between IAF quality and audit fees as well as a reduction in audit fees as a result of external auditors' reliance on IAF. The interaction between IAF quality and IAF contribution to external audit suggests that high quality IAF induces greater external auditor reliance on internal auditors' work and thus result in lower external audit fees.