Phosphorus bearing minerals in iron ores and their possible benefication

Modern electron optical techniques together with X-ray and mineralogical examination have been used to study the occurrence and form of phosphorus bearing minerals in iron ores. Three ores have been studied - Bahariya and Aswan from Egypt and Frodingham ironstone from U.K. The iron in the Bahariya iron ore is mainly as hematite and goethite. The gangue minerals are halite, gypsum, barytes, quartz and calcite. Iron content is between 49.8 to 63.2% and phosphorus 0.14 to 0.34%. The phosphorus occurs as very fine particles of apatite which are distributed throughout the ore. Removal of the phosphorus would require very fine grinding followed by acid leaching. Aswan iron ore is an oolitic iron ore; the iron content between 41-57% and phosphorus content 0.1 to 2.9%. It is mainly hematitic with variable quantities of quartz, apatite and small amount of clay minerals. In the oolitic iron ore beds, apatite occurs in the hematite matrix; filling in the pores of the oolithic surfaces, or as matrix cementing the ooliths with the hematite grains. In sandstone claybeds the distribution of the apatite is mainly in the matrix. It is suggested that the liberation size for the apatite would be -80 m and flotation concentration could be applied for the removal of apatite from Aswan ore. Frodingham ironstone occurs in the lower Jurassic bed of the South Humberside area. The average iron content is 25% and the phosphorus is 0.32%. Seven mineral phases were identified by X-ray; calcite, quartz, chamosite, hematite, siderite, apatite, and chlorite. Apatite occurs as very fine grains in the hematite and chamosite ooliths; as matrix of fine grains intergrown with chamosite and calcite grains; and as anhedral and sub rounded grains in the ooliths (8-28 m). It is suggested that two processes are possible for the dephosphorisation; the Flox process or a reduction roast followed by fine grinding, magnetic separation, and acid leaching.

Coarse-silt-fraction mineralogy at DSDP Legs 56 and 57 Holes

Soviet sedimentologists use the term "coarse silt" to denote the size fraction 0.1 to 0.05 mm (50-100 µm). Petelin (1961) has shown that this fraction is most diagnostic for terrigeneous and volcanogenic mineral assemblages and provinces in Recent deep-sea sediments, because of its greatest variability of both heavy and light non-opaque minerals, which may be easily identified by the common immersion method. We believe that the fraction is suitable for mineralogical study of unconsolidated and friable sediments from DSDP cores as well, if the objective is to investigate their source area and transporation tracks. In the case of fine-grained oceanic sediments, mineral composition of the coarse silt does not differ markedly from that of the "coarse fraction" (>62 µm).

Geochemistry of the Japan Trench sediments at DSDP Legs 56-57 Holes

The main objective of this investigation was to study distribution of main chemical constituents and several minor elements in sediment sections drilled during DSDP Legs 56 and 57 in the Japan Trench, in order to infer geochemical features of different lithologic types of sediments, and to find out how the geochemistry is associated with major lithologic constituents, such as terrigenous detrital matter, clay, volcanic ash, and biogenic particles. The geochemical data may help to indicate the nature of the sediments and to interpret sedimentation processes. The analyzed samples seem to be representative of most lithologic units, sub-units, and sediment types drilled at all sites on both legs, except for some shallow-water deposits at Sites 438 and 439. We analyzed bulk-sediment composition by X-ray fluorescence (Kuzmina and Turanskaya) and routine wet-chemical methods (Mikhailov); amorphous SiO2, extracted in a boiling sodium carbonate solution (Analythical Laboratory, P. P. Shirshov Institute of Oceanology); Cr, Zn, Cu, Ni, Co, and Al by atomic absorption (Gordeev); and Sn, Pb, Zn, Cu, Ni, Co, Cr, V, B, and Ag by quantitative spectrographic analyses in both bulk samples and granulometric fractions (Mikhailov). In addition, Fe, Ti, Mn, and CaCO3 have been determined in selected samples by routine wet-chemical methods (Analytical Laboratory, P. P. Shirshov Institute of Oceanology). Murdmaa was responsible for interpretation of the results.

Mineralogy and geochemistry of volcanic ash at Japan Trench from DSDP Legs 87 and 57

Volcanogenic sediments were obtained from Site 584, located on the midslope of the Japan Trench. Occurrences of volcanic ash in the diatomaceous mudstones increase within sediments dated 6-3 Ma. The frequency pattern and the sediment accumulation rate obtained at Site 584 are similar to those of Site 440 and to those of Sites 438 and 439, located on the upper slope basin. Explosive volcanism increased during the Pliocene and late Miocene in relation to the intrusion of Tertiary granites and uplift of the Tohoku Arc (northeastern Japan Arc). Hygromagmaphile element concentration shows that the glass does not belong to a unique series, and a comparison with Nankai Trough data distinguishes at least two different evolutionary lines.

Tris[4,4,4-trifluoro-1-(2-thienyl)butane-1,3-dionato]aluminium(III)-tris[4,4,4-trifluoro-1-(2-thienyl)butane-1,3-dionato]iron(III) (3/1)

In the title compound, [Al(C8H4F3O2S)3]3[Fe(C8H4F3O2S)3], the metal centre is statistically occupied by AlIII and FeIII cations in a 3:1 ratio. The metal centre is within an octahedral O6 donor set defined by three chelating substituted acetoacetonate anions. The ligands are arranged around the periphery of the molecule with a mer geometry of the S atoms.