Thermal–mechanical behaviour of chitosan–cellulose derivative thermoreversible hydrogel films

CH, Chitosan; HPMC, (Hydroxypropyl)methyl cellulose; FT, Freeze-thaw; SC, Solvent casting; CH:HPMC (X:Y), pH Z, FT/SC, Chitosan and (hydroxypropyl)methyl cellulose hydrogel, at X and Y proportion (0-100), at Z pH (3.0-4.0) and prepared by freeze-thaw or solvent casting techniques; DSC, Differential scanning calorimetry; MDSC, Temperature modulated Differential scanning calorimetry; Tg, glass transition temperature; ΔH, enthalpy change; TGA, Thermogravimetric Analysis; TG, Thermogravimetry; DTG, Derivative or Differential thermogravimetry; σ, Tensile strength; ε, elongation at break; DMA, Dynamic mechanical analysis; X-Ray, X-radiation, FTIR-ATR, Attenuated total reflectance Fourier transform infrared spectroscopy; SEM, Scanning electron microscopy.

Erratum to: Thermal–mechanical behaviour of chitosan–cellulose derivative thermoreversible hydrogel films

CH, Chitosan; HPMC, (Hydroxypropyl)methyl cellulose; FT, Freeze-thaw; SC, Solvent casting; CH:HPMC (X:Y), pH Z, FT/SC, Chitosan and (hydroxypropyl)methyl cellulose hydrogel, at X and Y proportion (0-100), at Z pH (3.0-4.0) and prepared by freeze-thaw or solvent casting techniques; DSC, Differential scanning calorimetry; MDSC, Temperature modulated Differential scanning calorimetry; Tg, glass transition temperature; ΔH, enthalpy change; TGA, Thermogravimetric Analysis; TG, Thermogravimetry; DTG, Derivative or Differential thermogravimetry; σ, Tensile strength; ε, elongation at break; DMA, Dynamic mechanical analysis; X-Ray, X-radiation, FTIR-ATR, Attenuated total reflectance Fourier transform infrared spectroscopy; SEM, Scanning electron microscopy.

Durabilidade de colagens estruturais em elementos de madeira

Dissertação de mestrado integrado em Engenharia Civil

Study of chemical modification of alkaline lignin by the glyoxalation reaction

In this study, glyoxalated alkaline lignins with a non-volatile and non-toxic aldehyde, which can be obtained from several natural resources, namely glyoxal, were prepared and characterized for its use in wood adhesives. The preparation method consisted of the reaction of lignin with glyoxal under an alkaline medium. The influence of reaction conditions such as the molar ratio of sodium hydroxide-to-lignin and reaction time were studied relative to the properties of the prepared adducts. The analytical techniques used were FTIR and 1H-NMR spectroscopies, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Results from both the FTIR and 1H-NMR spectroscopies showed that the amount of introduced aliphatic hydroxyl groups onto the lignin molecule increased with increasing reaction time and reached a maximum value at 10 h, and after they began to decrease. The molecular weights remained unchanged until 10 h of reaction time, and then started to increase, possibly due to the repolymerization reactions. DSC analysis showed that the glass transition temperature (Tg) decreased with the introduction of glyoxal onto the lignin molecule due to the increase in free volume of the lignin molecules. TGA analysis showed that the thermal stability of glyoxalated lignin is not influenced and remained suitable for wood adhesives. Compared to the original lignin, the improved lignin is reactive and a suitable raw material for adhesive formula

Characterization of alkaline lignins for use in penol-formaldehyde and epoxy resins

Besides polyurethanes and polyesters, phenolic and epoxy resins are the most prominent applications for technical lignins in thermosetting materials. To evaluate the potential application of lignin raw materials in phenol formaldehyde and epoxy resins, three types of alkaline lignins were characterized in terms of their structures and thermal properties. The lignin samples analyzed were kraft lignin (LIG-1), soda–rice straw lignin (LIG-2), and soda-wheat straw lignin (LIG-3). FTIR and 1H-NMR methods were used to determine their structure. Gel permeation chromatography (GPC) was used to determine the molecular weight distribution (MWD). Differential scanning calorimetry (DSC) was used to measure the glass transition temperature (Tg), and thermogravimetric analysis (TGA) to determine the thermal stability of lignin samples. Results showed that kraft lignin (LIG-1) has moderate hydroxyl-group content, is rich in G-type units, and has good thermal stability. These properties make it more suitable for direct use in phenol formaldehyde resins, and it is therefore a good raw material for this purpose. The alkaline soda-rice straw lignin (LIG-2) with a high hydroxyl-group content and excellent thermal stability is most suited to preparing lignin-based epoxy resin

PEG-b-PPS diblock copolymer aggregates for hydrophobic drug solubilization and release: cyclosporin A as an example

Micelles formed from amphiphilic block copolymers have been explored in recent years as carriers for hydrophobic drugs. In an aqueous environment, the hydrophobic blocks form the core of the micelle, which can host lipophilic drugs, while the hydrophilic blocks form the corona or outer shell and stabilize the interface between the hydrophobic core and the external medium. In the present work, mesophase behavior and drug encapsulation were explored in the AB block copolymeric amphiphile composed of poly(ethylene glycol) (PEG) as a hydrophile and poly(propylene sulfide) PPS as a hydrophobe, using the immunosuppressive drug cyclosporin A (CsA) as an example of a highly hydrophobic drug. Block copolymers with a degree of polymerization of 44 on the PEG and of 10, 20 and 40 on the PPS respectively (abbreviated as PEG44-b-PPS10, PEG44-b-PPS20, PEG44-b-PPS40) were synthesized and characterized. Drug-loaded polymeric micelles were obtained by the cosolvent displacement method as well as the remarkably simple method of dispersing the warm polymer melt, with drug dissolved therein, in warm water. Effective drug solubility up to 2 mg/mL in aqueous media was facilitated by the PEG- b-PPS micelles, with loading levels up to 19% w/w being achieved. Release was burst-free and sustained over periods of 9-12 days. These micelles demonstrate interesting solubilization characteristics, due to the low glass transition temperature, highly hydrophobic nature, and good solvent properties of the PPS block

Kosteuden ja lämpötilan vaikutus kartonkimassojen muovattavuuteen

Työn tavoitteena oli kartoittaa yleisesti kartongin valmistukseen käytettävien massatyyppien muovattavuuspotentaali. Muovattuvuuteen eniten vaikuttava tekijänä pidettiinmassojen murtovenymää. Työssä tutkittiin kosteuden ja lämpötilan sekä vetonopeuden vaikutusta mekaanisten ja sellumassojen ominaisuuksiin laboratorio-olosuhteissa. Kirjallisuusosassa tarkastellaan paperin lasisiirtymälämpötilaa muovauksen kannalta oleellisena tekijä. Lisäksi käydään läpi tapoja, joilla murtovenymää voidaan kasvattaa. Kartongin keskikerroksen aallotuksessa ja valmistettaessa paperipohjaisia tuotteita syvävedolla, käytetään hyväksi paperin pehmenemistä lämpötilan ja kosteuden alaisena. Niiden olosuhteita tarkastellaan lyhyesti. Lisäksi luodaan katsaus lämpötilan, kosteuden ja nopeuden vaikutuksistapaperin mekaanisiin ominaisuuksiin. Työn kokeellisessa osassa massojen mekaanisia ominaisuuksia testattiin erilaisissa kosteuspitoisuuksissasekä lämpötiloissa eri vetonopeuksilla. Kokeiden perusteella pyrittiin löytämään olosuhteet kullekin massalle, joissa niillä on paras murtovenymä. Lisäksi selvitettiin kuidun kihartamisen, sellumassojen jauhatuksen sekä arkin vapaan kuivumisen vaikutusta murtovenymään. Erilaiset massat saavuttavat parhaan murtovenymän erilaisissa kosteus- ja lämpötilaolosuhteissa. Sellumassoilla paras murtovenymä saadaan huoneenlämpötilassa ja paperin kosteuspitoisuuden ollessa välillä 11...12%. CTMP-massojen paras murtovenymä saadaan vedellä kyllästetyllä paperilla kohotetussa lämpötilassa. Lämpötila riippuu CTMP-massan valmistustavasta ja raaka-aineesta. Sellumassoilla on parempi kokonaisvenymä, kuin ligniinipitoisilla massoilla. Vetonopeuden vaikutus murtovenymään riippuu massasta sekä kosteudesta. Alhaisessa kosteudessa suurempi vetonopeus antaa aina pienemmän venymän. Kosteuden noustessa riippuu massasta, miten vetonopeus vaikuttaa murtovenymään. Plastinen osa tietystä venymästä on riippumaton massasta, jauhatusasteesta ja kuivatustavasta. Ainut vaikuttava muuttuja on kosteus. Kosteuden kasvu kasvattaa plastista venymää.

Hienopaperimassojen lujuusominaisuudet nopeassa vetokuormituksessa

Työssä verrattiin koivu-, akaasia- ja eucalyptussellujen käyttökelpoisuutta hienopapereiden kuituraaka-aineena. Kirjallisuusosassa todettiin radan hallinnan paperikoneiden avoimissa vienneissä riippuvan käytetyn geometrian lisäksi lujuus- ja relaksaatio-ominaisuuksista. Kuituverkoston käyttäytymiseen jännityksen alaisena vaikuttavat kuitudimensiot, kosteus ja lämpötila sekä kuituverkostoon kohdistetun jännityksen nopeus ja määrä. Relaksaationopeus ja vetolujuus kasvavat kuivilla papereilla vetonopeuden lisääntyessä. Kosteuspitoisuuden kasvattaminen alentaa puukuiduissa olevien polymeerien lasisiirtymälämpötilaa, jonka seurauksena vetolujuus ja relaksaatiokireys laskevat voimakkaasti. Kosteuspitoisuuden kasvaessa murtovenymä kasvaa lähes lineaarisesti ja repäisylujuus sekä murtotyö saavuttavat maksiminsa tietyssä kosteuspitoisuudessa. Kokeellisessa osassa keskityttiin hienopaperimassojen lujuus- ja relaksaatiokäyttäytymisen selvittämiseen nopeassa vetokuormituksessa. Lisäksi määritettiin laatu-, massa- ja rakenneominaisuuksia valituille koepisteille. Muuttujina kokeissa olivat massojen kuiva-ainepitoisuudet ja jauhatusolosuhteet sekä havusellun osuus hienopaperimassoissa.CSF-tasoon 350 ml jauhetuista näytteistä parhaat lujuus ja relaksaatio-ominaisuudet olivat koivulla ja heikoimmat akaasialla. Erot koepisteiden välillä korostuivat pienellä havusellun määrällä, mutta kaventuivat huomattavasti havusellun määrää lisättäessä. Samaan vetolujuuteen jauhettaessa massojen erot poistuvat kokonaan. Kuivilla näytteillä löydettiin erinomainen korrelaatio myötölujuuden ja relaksaatiokireyden välille. Puristinkuivien näytteiden relaksaatiokireyksiä voidaan kokeiden valossa ennustaa parhaiten kuivien näytteiden vetolujuuksista. Myös elastisten venymien osuuksille ja kuituseinämien paksuuksille löydettiin selvä yhteys.Eucalyptus- ja akaasiamassojen erinomaisuus hienopapereiden raaka-aineena korostui niiden optisissa ominaisuuksissa, erityisesti korkeana valonsirontana. Verrattaessa samassa vetolujuudessa ja relaksaatiokireydessä valonsirontakertoimien arvoja havaittiin akaasian olevan paras koivun jäädessä heikoimmaksi. Lisäksi akaasian ja eucalyptuksen kapeat kuitujakaumat ovat edullisia painokoneessa värin tasaisen imeytymisen kannalta. Akaasian pienet ja taipuisat kuidut antavat paperille tasaisen pinnan ja siten painatuksessa tasaisen painoalustan.

Determination of compression behaviour of coating layer

The strength properties of paper coating layer are very important in converting and printing operations. Too great or low strength of the coating can affect several problems in printing. One of the problems caused by the strength of coating is the cracking at the fold. After printing the paper is folded to final form and the pages are stapled together. In folding the paper coating can crack causing aesthetic damage over printed image or in the worst case the centre sheet can fall off in stapling. When folding the paper other side undergoes tensile stresses and the other side compressive stresses. If the difference between these stresses is too high, the coating can crack on the folding. To better predict and prevent cracking at the fold it is good to know the strength properties of coating layer. It has measured earlier the tensile strength of coating layer but not the compressive strength. In this study it was tried to find some way to measure the compressive strength of the coating layer and investigate how different coatings behave in compression. It was used the short span crush test, which is used to measure the in-plane compressive strength of paperboards, to measure the compressive strength of the coating layer. In this method the free span of the specimen is very small which prevent buckling. It was measured the compressive strength of free coating films as well as coated paper. It was also measured the tensile strength and the Bendtsen air permeance of the coating film. The results showed that the shape of pigment has a great effect to the strength of coating. Platy pigment gave much better strength than round or needle-like pigment. On the other hand calcined kaolin, which is also platy but the particles are aggregated, decreased the strength substantially. The difference in the strength can be explained with packing of the particles which is affecting to the porosity and thus to the strength. The platy kaolin packs up much better than others and creates less porous structure. The results also showed that the binder properties have a great effect to the compressive strength of coating layer. The amount of latex and the glass transition temperature, Tg, affect to the strength. As the amount of latex is increasing, the strength of coating is increasing also. Larger amount of latex is binding the pigment particles better together and decreasing the porosity. Compressive strength was increasing when the Tg was increasing because the hard latex gives a stiffer and less elastic film than soft latex.

Utilização do acetato de celulose produzido a partir da celulose extraída do caroço de manga como matriz para produção de sistemas microparticulados

Cellulose acetate produced from mango seed fibers cellulose was used as a matrix for preparation of microparticles empty and load with acetaminophen (Paracetamol) in order to evaluate the incorporation of an active agent during the formation of microparticles. The microparticles are characterized by Fourier Transformed Infrared spectroscopy (FTIR), Differential Scanning Calorimetry (DSC) and Scanning Electron Microscopy (SEM). The incorporation of paracetamol can be confirmed by the change in value of glass transition temperature (Tg). The formation of microparticles spherical was observed by SEM and showed an average diameter of 1.010 and 0.950 mm for empty and load microparticles respectively.

Síntese e caracterização de nanocompósitos de poliestireno/hidroxissal lamelar

Polystyrene/layered hydroxide salt (LHS) modified with sodium dodecyl sulfate was synthesized by in situ polymerization. The materials synthesized were characterized by gravimetry, X-ray diffraction (XRD), thermogravimetry analyses (TGA), differential scanning calorimetry (DSC) and the flammability test (FT). XRD demonstrated that synthesized nanocomposites in all compositions studied showed poor global dispersion of LHS in polystyrene. TGA showed a slight decrease in thermal stability. DSC curves showed that the glass transition temperature of polystyrene and nanocomposites were similar. The FT showed that the nanocomposite with low load of LHS exhibited good results.

Dielectric spectroscopy and thermally stimulated discharge current in PEEK film

The complex permittivity of films of polyether ether ketone (PEEK) has been investigated over a wide range of frequency. There is no relaxation peak in the range of 1Hz to 10(5) Hz but in the low-frequency side (10-4 Hz) there is an evidence of a peak that also can be observed by thermally stimulated discharge current measurements. That peak is related with the glass transition temperature (Tg) of the polymer. The activation energy of the relaxation was found to be 0.44 eV, similar to that of several synthetic polymers. Space charges are important in the conduction mechanism as shown by discharging transient.

Crystallization characteristics of bioactive glasses

Bioactive glasses are excellent candidates for implant materials, because they can form a chemical bond to bone or guide bone growth, depending on the glass composition. Some compositions have even shown soft tissue attachment and antimicrobial effects. So far, most clinical applications are based on monoliths, plates and particulates of different grain sizes. There is a growing interest in special products such as porous implants sintered from microspheres and fibers drawn from preforms or glass melts. The viscosity range at which these are formed coincides with the crystallization temperature range for most bioactive glasses, thus complicating the manufacturing process. In this work, the crystallization tendency and its kinetics for a series of glasses with their compositions within the range of bioactivity were investigated. The factors affecting crystallization and how it is related to composition were studied by means of thermal analysis and hot stage microscopy. The crystal compositions formed during isothermal and non-isothermal heat treatments were analyzed with SEM-EDXA and X-ray diffraction analysis. The temperatures at which sintering and fiber drawing can take place without interfering with crystallization were determined and glass compositions which are suitable for these purposes were established. The bioactivity of glass fibers and partly crystallized glass plates was studied by soaking them in simulated body fluid (SBF). The thickness of silica, calcium and phosphate rich reaction layers on the glass surface after soaking was used as an indication of the bioactivity. The results indicated that the crystallization tendencies of the experimental glasses are strongly dependent on composition. The main factor affecting the crystallization was found to be the alkali oxide content: the higher the alkali oxide content the lower the crystallization temperature. The primary crystalline phase formed at low temperatures in these glasses was sodium calcium silicate. The crystals were found to form through internal nucleation, leading to bulk crystallization. These glasses had high bioactivity in vitro. Even when partially crystalline, they formed typical reaction layers, indicating bioactivity. In fact, sodium calcium silicate crystals were shown to transform in vitro into hydroxyapatite during soaking. However, crystallization should be avoided because it was shown to retard dissolution, bioactivity reactions and complicate fiber drawing process. Glass compositions having low alkali oxide content showed formation of wollastonite crystals on the surface, at about 300°C above the glass transition temperature. The wide range between glass transition and crystallization allowed viscous flow sintering of these compositions. These glasses also withstood the thermal treatments required for fiber drawing processing. Precipitation of calcium and phosphate on fibers of these glasses in SBF suggested that they were osteoconductive. Glasses showing bioactivity crystallize easily, making their hot working challenging. Undesired crystallization can be avoided by choosing suitable compositions and heat treatment parameters, allowing desired product forms to be attained. Small changes in the oxide composition of the glass can have large effects and therefore a thorough understanding of glass crystallization behavior is a necessity for a successful outcome, when designing and manufacturing implants containing bioactive glasses.

The tautomerism, solvatochromism and non-linear optical properties of fluorescent 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine

The Schiff base, 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine, was synthesized by the condensation of 3-hydroxyquinoxaline-2-carboxaldehyde with 4-aminoantipyrine. HPLC, FT-IR and NMR spectral data revealed that the compound exists predominantly in the amide tautomeric form and exhibits both absorption and fluorescence solvatochromism, large stokes shift, two electron quasireversible redox behaviour and good thermal stability, with a glass transition temperature of 104oC. The third-order non-linear optical character was studied using open aperture Z-scan methodology employing 7 ns pulses at 532 nm. The third-order non-linear absorption coefficient, b, was 1.48 x 10-6 cm W-1 and the imaginary part of the third-order non-linear optical susceptibility, Im c(3), was 3.36 x10-10 esu. The optical limiting threshold for the compound was found to be 340 MW cm-2.

The tautomerism, solvatochromism and non-linear optical properties of fluorescent 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine

The Schiff base, 3-hydroxyquinoxaline-2-carboxalidine-4-aminoantipyrine, was synthesized by the condensation of 3-hydroxyquinoxaline-2-carboxaldehyde with 4-aminoantipyrine. HPLC, FT-IR and NMR spectral data revealed that the compound exists predominantly in the amide tautomeric form and exhibits both absorption and fluorescence solvatochromism, large stokes shift, two electron quasireversible redox behaviour and good thermal stability, with a glass transition temperature of 104 oC. The third-order non-linear optical character was studied using open aperture Z-scan methodology employing 7 ns pulses at 532 nm. The third-order non-linear absorption coefficient, b, was 1.48 x 10-6 cm W-1 and the imaginary part of the third-order non-linear optical susceptibility, Im c(3), was 3.36x10-10 esu. The optical limiting threshold for the compound was found to be 340 MW cm-2.