Momento da chuva após a aplicação e a eficácia dos herbicidas sulfosate e glyphosate aplicados em diferentes formulações

Com o objetivo de estudar a influência da chuva sobre o desempenho dos herbicidas sulfosate e glyphosate em diferentes formulações, foram conduzidos dois experimentos, um no inverno de 2000 e outro no verão de 2001, na Fazenda Experimental de Ensino e Pesquisa da Faculdade de Ciências Agrárias e Veterinárias, Campus de Jaboticabal-SP. Os experimentos foram instalados segundo o delineamento experimental de blocos ao acaso, com quatro repetições, no arranjo fatorial de 4x5+1, ou seja, quatro tratamentos de herbicidas, cinco períodos sem chuva após a aplicação e uma testemunha, que não recebeu chuva. As formulações de glyphosate foram: SAqC (1,0 L ha-1), GrDA (0,5 kg ha-1), SAqC Transorb (0,75 L ha-1), mais o sulfosate SAqC (1,09 L ha¹). Os períodos sem chuva após a aplicação foram de 1, 2, 4, 6 e > 48 horas. Os herbicidas foram aplicados em pós-emergência das plantas daninhas, utilizando-se de um pulverizador costal, à pressão constante (mantida por ar comprimido) de 30 lbf pol-2. A chuva foi simulada com um sistema de irrigação por aspersão. A lâmina de água variou entre 18 e 19 mm. em ambas as épocas, a chuva simulada foi prejudicial à ação dos herbicidas, principalmente quando feita nos menores intervalos após a aplicação. Os sintomas de fitointoxicação apareceram mais rapidamente no verão. A formulação Transorb, comercializada como não sendo afetada pela chuva uma hora após a aplicação, não teve o desempenho esperado, tanto no inverno quanto no verão, para períodos de até seis horas sem chuva após a aplicação. O sulfosate apresentou o melhor controle geral das plantas avaliadas, quando se simulou chuva após seis horas, em ambas as épocas. A formulação GrDA foi a mais afetada pela ação da chuva em ambas as épocas.

Eficácia de diferentes formulações no controle da mosca haematobia irritans em bovinos naturalmente infestados

This study evaluated the effectiveness of cypermethrin (5%) associated to Dichlorvos (45%) and piperonyl butoxide (25%) against Haematobia irritans in naturally infested cattle. 60 Nelore females, aging about 50 months, were separated into four groups with 15animals each. After randomization by the number of flies, the groups were divided in the following treatments: T1 = control, T2 and T4 = treated with the association under study at concentrations of 1: 400 and 1: 800, respectively, T3 = treated with cypermethrin 15% + clorpirivos 25% + citronella 1% (positive control) at a concentration of 1:800. Counst of flies were taken 3, 7, 14 and 21 days post treatment (DPT). In the third DPT, treatments T2, T3 and T4 showed efficacy over 98%. At the seventh day, it was found in animals treated with the compound containing piperonyl butoxide efficacy of 95.61 and 97.3% in the control of flies at dose of 1: 800 and 1: 400, respectively. While cattle in the T3 group demonstrated efficacy of 93.82%. The effectiveness of antiparasitic remained above 95% at 14 degrees DPT in both groups T2 and T4. In the same experimental day, animals of group T3 showed effectiveness of 88.24%. At 21 degrees DPT, only the T2 group, was significantly decreased (P <0.05) in the number of flies when compared to other treatments. Therefore, it was found in this study, the synergistic effect of piperonyl butoxide on the antiparasitic activity of synthetic pyrethroids and organophosphates, representing an effective alternative in the chemotherapy control by the parasitism for horn flies in cattle.

Acúmulo de nutrientes e matéria seca na parte aérea de dois cultivares de soja RR sob efeito de formulações de glyphosate

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Obtenção de placas cerâmico a partir de formulações de massas triaxiais de resíduos de caulim, chamote de telha e cinza vegetal

The production of red ceramic is an industrial activity that causes an intense impact. The manufacture of its products considerably increases the demand for natural resources, mainly with the extraction of raw material. The ceramic material produced generates waste, such as ash firewood and chamote. The residue from the beneficiation of kaolin is deposited in a poor, degrades the environment and contaminate water sources and soil, constituting in this manner, ecological disasters. The main objective of this work is to develop the formulation of a ceramic product consisting solely of industrial solid wastes, from ceramic tiles, (chamote) residue of kaolin and ash firewood. It is assumed that this product made in the laboratory can be used in coatings, wall and floor. The aim is to facilitate the replacement of the raw material of original composition of a ceramic body, for waste, while the process of production equal to the conventionally used, so that the properties of the product are reproduced. This work is characterized waste as its chemical composition, analysis of particle size, X-ray diffraction and thermal behavior. Several formulations were studied. The mass of waste was prepared by dry process, pressed to 25 MPa, and then burned in muffle type oven to 850, 950, 1050 and 1150 °C. The results showed that it is technically possible to produce porous tiles only with waste. It was found that the formulations of bodies play a key role in the properties of the final product, as well as the sintering temperature and heating rates. RN in the waste of kaolin is estimated at 15,000 t/month, about 3,000 gray t/month and chamote with 10 million pieces/month damaged. The presence of carbonates of calcium and magnesium at 1050 ° C results in an appropriate porosity and mechanical strength. The formulation M3JE, composed of 69% waste of kaolin, 7.7% and 23.3% of chamote of gray, became suitable for porous materials with the strength and absorption within the level of national and international standards

Caracterização de matérias-primas regionais e desenvolvimento de formulações de massas cerâmicas para porcelanato

Initially concentrated in some poles at the South and Southeast regions of Brazil, the ceramic tiles industry became wide during the 80 s decade, with a disconcentration industrial and regional pulverization. The competitiveness in the ceramic tiles internal and external consumers markets, it has debtor the industries to invest in sophisticated products each time more, either in design or the technology, but, mainly, in its final properties. Amongst the diverse types of ceramic coating, the porcelanato if has detached had to its process of technological production and excellent characteristics techniques. The Porcelanato is currently the material for coatings that presents the best technical and aesthetic features when compared with others ceramics found on the market. The chemical composition and the others raw materials characteristics have an importance that must to be ally to the inherent characteristics of fabrication process, essentially those related to the cycle of burning. This work had as purpose to develop formularizations of ceramic mass for production of porcelanato without glass coating, pertaining to the group BIa (text of absorption of water ≤ 0.5%) and with resistance superior mechanics 35MPa from raw materials characterized. The ceramic raw materials selected to the development of this study (A1 and A2 clays, feldspate, talc and quartz) were submitted to the following tests: X-ray fluorescence - chemical analysis determination; X-ray diffraction - Analysis of the stages mineralogics; Laser granulometry - size distribution of particles; and Differential thermal analysis - thermal behavior. Were performed tests of absorption of water, lineal retraction of it burns, apparent specific mass and rupture tension the flexing. The results had evidenced that the formularizations that had the A1 clay and talc on its composition were efficient for the porcelanato production remaining their technological characteristics inside of the intervals of variation desired by the Norms of the ABNT

Estudo da introdução de resíduo de britagem de rocha calcária e cinza de biomassa de cana-de-açúcar em formulações de argamassas colantes

The adhesive mortars are a mixture of cement, sand, and additives to polymers that retain the mixing water and promotes adherence, being used in setting on various ceramic substrates. The sand used in the production of these mortars is from the riverbeds, and with the increasing restriction of these sands extraction by environmental agencies, and often having to be transported over long distances to the consumer center. This work aims to design and physical and mechanical characterization of ecological adhesive mortar with total replacement of natural sand by sand from the crushing of limestone, and the addition of mineral ash biomass of cane sugar in partial replacement cement used in the production of adhesive mortar , aiming compositions that meet the regulatory specifications for use adhesive mortar. Standardized tests to determine the tensile bond strength (NBR 14081-4), determination of open time (NBR 14081-3) and determination of slip (NBR 14081-5) were performed. Were also conducted trials squeeze flow in different formulation, the mortar with addition of 15 % gray biomass of cane sugar for cement mortars as well as the total replacement of natural sand by sand limestone crushing, got the best performance among the mortars studied, it was found that the addition of biomass to replace cement is perfectly feasible due to its pozzolanic activity, which contributed to this reduction in the cement matrix formation of adhesive mortar

Efeito da concentração do amido de milho na liberação de paracetamol de comprimidos

Este trabalho avaliou a influência da concentração de amido de milho nas características físicas e na liberação in vitro de paracetamol a partir de comprimidos. Os granulados foram analisados quanto à granulometria e densidades aparentes bruta e compactada e os comprimidos quanto ao peso médio, espessura, dureza, friabilidade, tempo de desintegração. Os comprimidos foram preparados a partir de granulados obtidos por granulação a úmido, utilizando cozimento de amido a 10% como agente granulante, segundo três formulações. Embora os comprimidos obtidos tenham apresentado características dentro dos limites farmacopéicos, os resultados indicam que variações da concentração de amido provocam diferenças nos diversos parâmetros físicos estudados. Concentração mais alta de amido em pó dá origem, provavelmente, à interação entre os componentes da fórmula, interferindo na liberação in vitro do fármaco. Isto demonstra a importância de se otimizar a concentração dos adjuvantes numa formulação de comprimidos, pois, embora uma pequena variação nesta concentração não exerça efeito significativo no tempo de desintegração, a quantidade de fármaco liberado pode ser substancialmente alterada.

Novas formulações de fluidos de corte: otimização, propriedades e recuperação do óleo usado

Cutting fluids are lubricants used in metal-mechanical industries. Their complex composition varies according to the type of operation carried out, also depending on the metals under treatment or investigation. Due to the high amount of mineral oil produced in Northeastern Brazil, we have detected the need to better use this class of material. In this work, two novel formulations have been tested, both based on naphthenic mineral oil and additives, such as: an emulsifying agent (A), an anticorrosion agent (B), a biocide (C) and an antifoam agent (D). Each formulation was prepared by mixing the additives in the mineral oil at a 700-rpm stirring velocity for 10 min, at 25°C, employing a 24 factorial planning. The formulations were characterized by means of density, total acid number (TAN), viscosity, flash point and anticorrosion activity. In a subsequent study, oil-in-water emulsions were prepared from these novel formulations. The emulsions were analyzed in terms of stability, corrosion degree, percentage of foam formation, conductivity, accelerated stability and particle size. The samples were appropriately labeled, and, in special, two of them were selected for featuring emulsion properties which were closer to those of the standards chosen as references (commercial cutting oils). Investigations were undertaken on the ability of NaCl and CaCl2 to destabilize the emulsions, at concentrations of 2%, 5% and 10%, at an 800-rpm stirring velocity for 5 min and temperatures of 25º, 40º, 50º and 60ºC. The recovered oils were chemically altered by reincorporating the same additives used in the original formulations, followed by preparation of emulsions with the same concentrations as those of the initial ones. The purpose was to assess the possibility of reusing the recovered oil. The effluents generated during the emulsion destabilization step were characterized via turbidity index, contents of oil and grease, pH, and contents of anions and cations, observing compliance with the parameters established by the current environmental legislation (Brazil s CONAMA 357/05 resolution). It could be concluded that the formulations presented excellent physicochemical properties as compared to commercial cutting fluids, showing that the quality of the newly-prepared fluids is superior to that of the formulations available in the market, enabling technically and environmentally-safe applications

Negociações comerciais internacionais e democracia: o contencioso Brasil x EUA das patentes farmacêuticas na OMC

Dans cet article, on cherche la viabilité analytique du Jeu à Deux Niveaux - JDN pour examiner la situation brésilienne dans l'Organisation Mondiale du Commerce - OMC. on cherche à voir, en même temps, si le perfectionnement des institutions démocratiques brésiliennes en ce qui concerne le processus de formulation de la politique extérieure sera capable d'améliorer la réponse aux demandes des groupes d'intérêt et d'élargir la compétence technique de la diplomatie brésilienne dans les négociations commerciales internationales. on cherche aussi à savoir si ce perfectionnement peut faire monter la crédibilité et la légitimité internationale des démarches brésiliennes au sein de l'OMC, dans le sens de tourner en leur faveur les régimes internationaux. Pour cela, on analyse le contentieux des brevets pharmaceutiques mené contre les États-Unis au sein de l'OMC.

Efeito do teor de soro, açúcar e de frutooligossacarídeos sobre a população de bactérias lácticas probióticas em bebidas fermentadas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise do comportamento de queima de argilas e formulações para revestimento cerâmico

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação do íon ferro em preparações farmacêuticas através da cromatografia planar e espectrofotometria

Os autores estudaram o comportamento cromatográfico de preparações farmacêuticas comerciais contendo o íon Fe (II). Utilizando celulose microcristalina/Propanol: ácido clorídrico 4 N: ácido acético concentrado: ácido nítrico concentrado: clorofórmio (40: 5: 5: 10: 10), como sistema cromatográfico e alizarina como reagente de detecção, Fe (II), Mn (II), Mg (II), Cu (II), Zn (II) e Ca (II) foram separados e identificados pela Cromatografia Planar. O Fe (II) foi determinado pela reação com a ortofenantrolina, resultando em solução adequada para quantificação colorimétrica.

Aplicação e avanços da espectroscopia de luminescência em análises farmacêuticas

This paper provides a review on the latest advances and applications of the luminescence spectroscopy for the development of pharmaceuticals analyses methods, basically based on the photo- and chemiluminescence. The different forms of the drugs determination on pharmaceuticals through the fluorescence and chemiluminescence are discussed. The analyses include the drugs native fluorescence (liquid and solid-phases); the fluorescence from the oxidizing or reducing forms of the drug; the fluorescence from the chemical derivatization and their photochemistry and hydrolysis reactions. The quenching of luminescence and chemiluminescence generation for the pharmaceutical quantification are also shown. Finally, the trends and future perspectives of the luminescence spectroscopy in the field of the pharmaceutical research are discussed.

Determinação espectrofotométrica por injeção em fluxo de glifosato em formulações comerciais de herbicidas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Segurança no trabalho de preparo de calda no tanque de 2.000l do turbopulverizador com formulações líquidas de agrotóxicos registradas para a cultura de goiaba

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)