Elemental analysis of soil samples for forensic purposes by inductively coupled plasma spectrometry - precision considerations

Major and trace elemental composition provides a powerful basis for forensic comparison of soils, sediments and rocks. However, it is important that the potential 'errors' associated with the procedures are fully understood and quantified, and that standard protocols are applied for sample preparation and analysis. This paper describes such a standard procedure and reports results both for instrumental measurement precision (repeatability) and overall 'method' precision (reproducibility). Results obtained both for certified reference materials and example soils show that the instrumental measurement precision (defined by the coefficient of variation, CV) for most elements is better than 2-3%. When different solutions were prepared from the same sample powder, and from different sub-sample powders prepared from the same parent sample, the CV increased to c. 5-6% for many elements. The largest variation was found in results for certified reference materials generated from 23 instrument runs over an 18 month period (mean CV=c. 11%). Some elements were more variable than others. W was found to be the most variable and the elements V, Cr, Co, Cu, Ni and Pb also showed higher than average variability. SiO2, CaO, Al2O3 and Fe2O3, Rb, Sr, La, Ce, Nd and Sm generally showed lower than average variability, and therefore provided the most reliable basis for inter-sample comparison. It is recommended that, whenever possible, samples relating to the same investigation should be analysed in the same sample run, or at least sequential runs.

Forensic analysis of architectural finishes using Fourier transform infrared and Raman spectroscopy, Part I: The resin bases

The ability of Raman spectroscopy and Fourier transform infrared (FT-IR) microscopy to discriminate between resins used for the manufacture of architectural finishes was examined in a study of 39 samples taken from a commercial resin library. Both Raman and FT-IR were able to discriminate between different types of resin and both split the samples into several groups (six for FT-IR, six for Raman), each of which gave similar, but not identical, spectra. In addition, three resins gave unique Raman spectra (four in FTIR). However, approximately half the library comprised samples that were sufficiently similar that they fell into a single large group, whether classified using FT-IR or Raman, although the remaining samples fell into much smaller groups. Further sub-division of the FT-IR groups was not possible because the experimental uncertainty was of similar magnitude to the within-group variation. In contrast, Raman spectroscopy was able to further discriminate between resins that fell within the same groups because the differences in the relative band intensities of the resins, although small, were larger than the experimental uncertainty.

Rapid forensic analysis and identification of "lilac" architectural finishes using Raman spectroscopy

The potential of Raman spectroscopy to discriminate between architectural finishes (household paint) has been investigated using a test set of 51

A preliminary investigation into the use of testate amoebae for the discrimination of forensic soil samples

We present the results of an initial investigation into the efficacy of using testate amoebae for the discrimination of soils from wet ground and puddles, as little attention has been given to these organisms in forensic science. The preservation of testate amoebae in these sediments is generally good, although test concentrations are low. Statistical analysis suggests that restate amoebae assemblages are somewhat spatially distinct and have potential to be used for soil discrimination. A case study is presented where mineralogical (X-ray diffraction) and restate amoebae analyses are used in conjunction to clarify the scene of crime in a 'cold case' murder enquiry. Testate amoebae were recovered from dried sediment residues on clothing 10 years after the murder. Despite these promising results, further experimental work is crucial to examine the spatial and temporal variation of amoebae assemblages in water films, wet ground and puddles before they can be added to the armoury of methods available to the forensic biologist.

Forensic Geology in Environmental Crime: Illegal Waste Movement Burial in Northern Ireland

The illegal burial of waste often occurs in locations where loose, transferable material is abundant, allowing covert pits to be dug or filled. The transfer of waste material onto suspects and their vehicles during loading, unloading, and burial is common, as is the case during other criminal activities such as the burial of murder victims. We use two case studies to show that the established principles of using geological materials in excluding or linking suspects can be applied to illegal waste disposal. In the first case, the layering of different geological materials on the tailgate of a container used to transport toxic waste demonstrated where the vehicle had been and denied the owner's alibi, associating him with an illegal dumpsite. In the second case, an unusual suite of minerals, recovered from a suspect's trousers, provided the intelligence that led environmental law enforcement officers to an illegal waste burial site.

Forensic examination of multilayer white paint by lateral scanning Raman spectroscopy

Multilayer samples of white architectural paint potentially have very high evidential value in forensic casework, because the probability that two unrelated samples will have the same sequence of layers is extremely low. However, discrimination between the different layers using optical microscopy is often difficult or impossible. Here, lateral scanning Raman spectroscopy has been used to chemically map the cross-sections of multilayer white paint chips. It was found that the spectra did allow the different layers to be delineated on the basis of their spectral features. The boundaries between different layers were not as sharp as expected, with transitions occurring over length scales of > 20 µm, even with laser spot diameters <4 µm. However, the blurring of the boundaries was not so large as to prevent recording and identification of spectra from each of the layers in the samples. This method clearly provides excellent discrimination between different multilayer white paint samples and can readily be incorporated into existing procedures for examination of paint transfer evidence.