Optimised polyolefin branch quantification by 13 C NMR spectroscopy

Quantitative branch determination in polyolefins by solid- and melt-state 13C NMR has been investigated. Both methods were optimised toward sensitivity per unit time. While solid-state NMR was shown to give quick albeit only qualitative results, melt-state NMR allowed highly time efficient accurate branch quantification. Comparison of spectra obtained using spectrometers operating at 300, 500 and 700 MHz 1H Larmor frequency, with 4 and 7~mm MAS probeheads, showed that the best sensitivity was achieved at 500 MHz using a 7 mm 13C-1H optimised high temperature probehead. For materials available in large quantities, static melt-state NMR, using large diameter detection coils and high coil filling at 300 MHz, was shown to produce comparable results to melt-state MAS measurements in less time. While the use of J-coupling mediated polarisation transfer techniques was shown to be possible, direct polarisation via single-pulse excitation proved to be more suitable for branch quantification in the melt-state. Artificial line broadening, introduced by FID truncation, was able to be reduced by the use of π pulse-train heteronuclear dipolar decoupling. This decoupling method, when combined with an extended duty-cycle, allowed for significant improvement in resolution. Standard setup, processing and analysis techniques were developed to minimise systematic errors contributing to the measured branch contents. The final optimised melt-state MAS NMR method was shown to allow time efficient quantification of comonomer content and distribution in both polyethylene- and polypropylene-co-α-olefins. The sensitivity of the technique was demonstrated by quantifying branch concentrations of 8 branches per 100,000 CH2 for an industrial ‘linear’ polyethylene in only 13 hours. Even lower degrees of 3–8 long-chain branches per 100,000 carbons were able to be estimated in just 24 hours for a series of γ-irradiated polypropylene homopolymers.

Functional thin films fabricated by plasma polymerization and their biological applications

Plasma polymerization technique is widely accepted as an effective and simple method for the preparation of functional thin films. By careful choice of precursors and deposition parameters, plasma polymers bearing various functional groups could be easily obtained. In this work, I explored the deposition of four kinds of plasma polymerised functional thin films, including the protein-resistant coatings, the thermosensitive coatings, as well as, the coatings bearing amine or epoxide groups. The deposited plasma polymers were characterized by various techniques, such as X-ray photoelectron spectroscopy, atom force microscopy, Fourier transform infrared spectroscopy, surface plasmon resonance spectroscopy, optical waveguide spectroscopy, and so on. As expected, high retention of various functional groups could be achieved either at low plasma input power or at low duty cycle (duty cycle = Ton/(Ton+Toff)). The deposited functional thin films were found to contain some soluble materials, which could be removed simply by extraction treatment. Besides the thermosentive plasma polymer (see Chapter 9), other plasma polymers were used for developing DNA sensors. DNA sensing in this study was achieved using surface plasmon enhanced fluorescence spectroscopy. The nonfouling thin films (i.e., ppEO2, plasma polymerization of di(ethylene glycol) monovinyl ether) were used to make a multilayer protein-resistant DNA sensor (see Chapter 5). The resulted DNA sensors show good anti-fouling properties towards either BSA or fibrinogen. This sensor was successfully employed to discriminate different DNA sequences from protein-containing sample solutions. In Chapter 6, I investigated the immobilization of DNA probes onto the plasma polymerized epoxide surfaces (i.e., ppGMA, plasma polymerization of glycidyl methacrylate). The ppGMA prepared at a low duty cycle showed good reactivity with amine-modified DNA probes in a mild basic environment. A DNA sensor based on the ppGMA was successfully used to distinguish different DNA sequences. While most DNA detection systems rely on the immobilization of DNA probes onto sensor surfaces, a new homogeneous DNA detection method was demonstrated in Chapter 8. The labeled PNA serves not only as the DNA catcher recognizing a particular target DNA, but also as a fluorescent indicator. Plasma polymerized allylamine (ppAA) films were used here to provide a positively charged surface.

Untersuchungen zur Lebensdauer von NEA-Photokathoden bei der Extraktion sehr hoher mittlerer Ströme

Die Produktion eines spinpolarisierten Strahls mit hohem mittleren Strom ist sowohl für den Betrieb von existierenden polarisierten Quellen als auch in noch stärkerem Maße für geplante zukünftige Projekte wichtig. Die Betriebszeit solcher Quellen wird durch die Abnahme der Quantenausbeute der Photokathode mit der Zeit begrenzt. Die Problematik der Abnahme der Quantenausbeute konnte durch die Reaktion der Kathodenoberfläche mit sauerstoffhaltigen Molekülen sowie durch Ionenbombardement geklärt werden. Im Laufe dieser Arbeit wurden, teilweise zum ersten Mal, Mechanismen untersucht, die zur Entstehung der chemisch aktiven Moleküle und der Ionen beitragen und weitere Effekte, die die Betriebszeit der polarisierten Quellen reduzieren. Die Experimente wurden an einer genauen Kopie der an MAMI vorhandenen polarisierten Quelle durchgeführt. Es wurde demonstriert, dass Erwärmung der Photokathode, Ioneneinfang und Strahlverlust aufgrund der Raumladungskräfte die Kathodenlebensdauer begrenzen können. Der erste Effekt ist Erwärmung der Photokathode. Die Laserleistung wird fast vollständig in Wärmeleistung umgesetzt, was zur Absenkung der Verfügbarkeit der polarisierten Quellen führen kann, und zwar unabhängig davon, ob der Photostrom produziert wird oder nicht. Der zweite Effekt ist Ionenbombardement mit den sowohl in der Beschleunigungsstrecke als auch in der Strahlführung entstehenden Ionen. Es wurde demonstriert, dass der in der Strahlführung entstehende Ionenstrom sogar größer ist als der in der Kanone. Unter bestimmten Bedingungen können die gebildeten Ionen durch das Potenzial des Elektronenstrahls eingefangen werden und die Kanone erreichen und damit zusätzlich zur Zerstörung der negativen Elektronenaffinität beitragen. Der dritte Effekt ist Strahlverlust. Es wurde demonstriert, dass die relativen Strahlverluste kleiner als 1*10-6 sein sollten, um eine Lebensdauer von mehr als 1000 Stunden beim Strom von 100 A zu erreichen, was für die vorhandene Apparatur möglich ist. Zur Erzeugung extrem hoher Ströme wurde zum ersten Mal im Bereich der spinpolarisierten Quellen das Prinzip der „Energierückgewinnung“ eingesetzt. Experimente bei einer mittleren Stromstärke von 11.4 mA und einer Spitzenstromstärke von 57 mA bei 1% Tastverhältnis wurden bereits durchgeführt.

Evaluation von Effektivität und Sicherheit der niederfrequenten, transkraniellen Ultraschalltherapie beim Schlaganfall

In den westlichen Ländern nimmt die Zahl der Schlaganfall-Patienten stetig zu und zählt mittlerweilernzu einer der häufigsten Todesursachen. Derzeit ist die Rekanalisationstherapie mit demrnFibrinolytikum rt-PA die einzig zugelassene Therapie. Die Rekanalisationsrate ist oftmals inkomplettrnund aufgrund von möglichen Blutungskomplikationen die Therapie nicht bei allen Patientenrnmöglich. Daher ist es wichtig, Alternativtherapieansätze (z.B. Ultraschallthrombolyse) zurnentwickeln. Blutgerinnsel können mit Hilfe von Ultraschall in Schwingung gebracht und sornlysiert oder die Wirkung von rt-PA verstärkt werden. Die vorliegende Arbeit hatte die Evaluationrnvon Bioeffekten von 60 kHz Ultraschall an gesundem und ischämischem Hirngewebe zum Ziel.rnNeben tierexperimentellen Methoden kamen auch molekular-biologische Techniken zur Anwendung.rnDie erste Studie beschäftigte sich mit der Wirkung von 60 kHz (Intensität: 0,2 W/cm2 undrnDuty Cycle 50%) auf ischämisches Hirngewebe (permanent ischämisch und nach Reperfusion).rnLediglich nach Reperfusion und Ultraschallbehandlung war das Läsionsvolumen signifikantrnerhöht, so dass von einer besonderen Vulnerabilität des Hirngewebes nach Reperfusionrnauszugehen ist (Penumbraschädigung). In der neurologischen Beurteilung der Tiere zeigte sichrnbei allen Tieren mit permanenter Okklusion und etwa einem Drittel der Tiere nach Reperfusionrnund Ultraschallbehandlung eine Hörminderung. In der anschließenden Studie wurde diernUltraschallintensität erniedrigt und der Duty Cycle variiert. In einer publizierten in vitro Studiernkonnte die zunehmende Lyserate mit steigendem Duty Cycle nachgewiesen werden. DiernAuswertung ergab eine Abhängigkeit des Läsionsvolumens von der Länge des Duty Cycles. Derrndritte Teil der Arbeit befasst sich mit der Wirkung von Ultraschall auf die Genexpression. Hierzurnwurden gesunde Ratten mit Ultraschall verschiedener Frequenzen (60 kHz, 488 kHz und 3 MHz)rntranskraniell behandelt und 4 h bzw. 24 h nach der Behandlung getötet. Proben von ischämischenrnTieren dienten als positive Kontrollen. Aufgrund von Literaturrecherchen wurden mehrerernKandidatengene ermittelt. Die Messung der Ischämieproben ergab eine weitgehende Übereinstimmungrnmit der Literatur. Die Messungen an den mit 60 kHz behandelten Proben ergabenrnkaum Anzeichen für eine differenzielle Genregulation. Die Frequenz von 488 kHz zeigte diernmeisten Regulationen, gefolgt von der Behandlung mit 3 MHz. Dieses Ergebnis lässt vermuten,rndass es sich bei den detektierten Veränderungen um protektive Mechanismen handelt, da diesernFrequenzen bislang im Tierversuch als nebenwirkungsarm beschrieben wurden. Die Auswertungrnvon 60 kHz-Proben mit Affymetrix Arrays ergab lediglich einige wenige differentiell regulierternGene. Die Array-Experimente konnten nicht durch qPCR-Messungen bestätigt werden.

Studio dei circuiti di clamper negli amplificatori operanti in classe e

Questa tesi tratta dell’amplificatore di potenza (PA–Power Amplifier) operante in classe E. Si tratta di un convertitore DC/AC ad elevato rendimento che può trovare impiego in numerose applicazioni in cui il problema della generazione di calore o la necessità di non sprecare energia sono particolarmente stringenti (ad esempio apparati per cui non è previsto un impianto di raffreddamento e/o apparati alimentati a batteria). L’elevato rendimento di un amplificatore operante in classe E deriva dalle specifiche forme d’onda ai capi del dispositivo attivo impiegato, tali per cui la perdita di commutazione durante la fase di accensione dello switch diviene pressoché trascurabile (Zero-Voltage-Switching e Zero-Derivative-Voltage Turn-ON). Il prezzo da pagare per ottenere queste benefiche forme d’onda è quello di avere un valore di cresta della tensione sul dispositivo che commuta assai più elevato del valore medio, coincidente con la tensione di alimentazione DC. In generale si stima una tensione di picco fra le 3 e le 5 volte più elevata della tensione DC, in funzione del Duty-Cycle e dell’assorbimento di corrente sul carico. Occorre poi tenere presente che in condizioni dinamiche (ad esempio qualora si collegasse direttamente l’amplificatore all’alimentazione) potrebbero innescarsi dei transitori tali per cui la tensione di picco ecceda anche il range suddetto. Per questo motivo è bene porre un limite alla massima tensione di picco adottando dei circuiti di protezione del transistore al fine di evitare la sua distruzione per limiti legati alla tensione di breakdown. Questi circuiti sono denominati clamper: in questa tesi valuteremo le modalità con cui si può implementare tale protezione; valuteremo, inoltre, i vantaggi e gli svantaggi derivanti dall’impiego di tali circuiti. Questi clamper sono prevalentemente di tipo dissipativo (Zener); nel corso della tesi si è studiato la realizzazione di un clamper rigenerativo che utilizza un trasformatore, ma si è constatata la irrealizzabilità fisica a causa della inevitabile presenza della induttanza dispersa.

Studio del convertitore Buck Boost non invertente a ponte di interruttori

La tesi tratta del convertitore Buck Boost a ponte di interruttori e non invertente. Si tratta di due LEG indipendenti connessi da un induttore e che possono realizzare conversioni rispettivamente in discesa e salita. Questo convertitore soffre di problemi di controllo nel passaggio dalla modalità di salita a quella di discesa e viceversa e nella gestione di tensioni molto vicine alla regione di confine a causa delle limitazioni nei duty cycle massimi e minimi dei singoli LEG. Nella tesi si è studiato una tecnica di controllo in grado di gestire la transizione con una minima variazione di corrente media sull' elemento di transfer energetico: questo dovrebbe garantire delle migliori prestazioni in dinamica. La tecnica adottata è anche compatibile con una sostanziale riduzione delle perdite di commutazione nella zona di transizione fra le due modalità (salita e discesa).

Studio di un algoritmo di controllo di temperatura per ganasce termosigillanti in macchine per packaging

Gli obiettivi dell'elaborato sono lo studio e la programmazione di un algoritmo di controllo di temperatura per le superfici termosaldanti di macchine per il packaging (confezionatrici in film a file multiple) prodotte dal committente, OMAG srl. L'algoritmo è implementato tramite il software SoMachineMotion v.4.2, prodotto da Schneider Electrics spa. Il controllo è di tipo in anello chiuso in retroazione, con temocoppie e resistenze di riscaldamento con modulazione PWM. Ci si è inizialmente occupati di testare su banco prova varie tipologie di regolatori: a relay, a isteresi, a ricerca diretta del duty cycle, TBH, con approccio misto TBH/integratore di Clegg, PID. I diversi metodi di regolazione sono stati valutati sulla base di una serie di metri di giudizio (precisione dell'inseguimento, prestazioni statiche e dinamiche, flessibilità, peso computazionale, facilità implementativa), pesati secondo i requisiti imposti dal committente. Le metodologie selezionate sono state PID e TBH/Clegg integrator; quest'ultima ha dato risultati assai soddisfacenti, pur essendo un metodo monoparametrico. Si sono quindi studiate diverse modalità per la taratura del regolatore PID, in particolare: tuning in anello chiuso con metodo a relay per la fase di pretuning, algoritmo di Nelder-Mead, per la ricerca diretta continua dei valori che minimizzano l'errore integrale, per un selftuning adattivo. Si è infine proceduto ad implementare le soluzioni individuate in un software robusto, che rispetti gli standard del settore e si sono inoltre sviluppate una serie di funzionalità aggiuntive, quali: modulazione software PWM, preriscaldamento, handling errori/warning, filtraggio segnali in/out. Si è addizionalmente sviluppato un modello matematico predittivo dell'evoluzione del sistema, che potrebbe servire, in un futuro sviluppo, come base per un controllo model-based in cascata al controllo in retroazione studiato.

Assessment of detectability of neutral interstellar deuterium by IBEX observations

Context. The abundance of deuterium in the interstellar gas in front of the Sun gives insight into the processes of filtration of neutral interstellar species through the heliospheric interface and potentially into the chemical evolution of the Galactic gas. Aims: We investigate the possibility of detection of neutral interstellar deuterium at 1 AU from the Sun by direct sampling by the Interstellar Boundary Explorer (IBEX). Methods: Using both previous and the most recent determinations of the flow parameters of neutral gas in the local interstellar cloud (LIC) and an observation-based model of solar radiation pressure and ionization in the heliosphere, we simulated the flux of neutral interstellar D at IBEX for the actual measurement conditions. We assessed the number of interstellar D atom counts expected during the first three years of IBEX operation. We also simulated the observations expected during an epoch of high solar activity. In addition, we calculated the expected counts of D atoms from the thin terrestrial water layer covering the IBEX-Lo conversion surface, sputtered by neutral interstellar He atoms. Results: Most D counts registered by IBEX-Lo are expected to come from the water layer, exceeding the interstellar signal by 2 orders of magnitude. However, the sputtering should stop once the Earth leaves the portion of orbit traversed by interstellar He atoms. We identify seasons during the year when mostly the genuine interstellar D atoms are expected in the signal. During the first 3 years of IBEX operations about 2 detectable interstellar D atoms are expected. This number is comparable to the expected number of sputtered D atoms registered during the same time intervals. Conclusions: The most favorable conditions for the detection occur during low solar activity, in an interval including March and April each year. The detection chances could be improved by extending the instrument duty cycle, say, by making observations in the special deuterium mode of IBEX-Lo.

Improving 4D plan quality for PBS-based liver tumour treatments by combining online image guided beam gating with rescanning.

Pencil beam scanned (PBS) proton therapy has many advantages over conventional radiotherapy, but its effectiveness for treating mobile tumours remains questionable. Gating dose delivery to the breathing pattern is a well-developed method in conventional radiotherapy for mitigating tumour-motion, but its clinical efficiency for PBS proton therapy is not yet well documented. In this study, the dosimetric benefits and the treatment efficiency of beam gating for PBS proton therapy has been comprehensively evaluated. A series of dedicated 4D dose calculations (4DDC) have been performed on 9 different 4DCT(MRI) liver data sets, which give realistic 4DCT extracting motion information from 4DMRI. The value of 4DCT(MRI) is its capability of providing not only patient geometries and deformable breathing characteristics, but also includes variations in the breathing patterns between breathing cycles. In order to monitor target motion and derive a gating signal, we simulate time-resolved beams' eye view (BEV) x-ray images as an online motion surrogate. 4DDCs have been performed using three amplitude-based gating window sizes (10/5/3 mm) with motion surrogates derived from either pre-implanted fiducial markers or the diaphragm. In addition, gating has also been simulated in combination with up to 19 times rescanning using either volumetric or layered approaches. The quality of the resulting 4DDC plans has been quantified in terms of the plan homogeneity index (HI), total treatment time and duty cycle. Results show that neither beam gating nor rescanning alone can fully retrieve the plan homogeneity of the static reference plan. Especially for variable breathing patterns, reductions of the effective duty cycle to as low as 10% have been observed with the smallest gating rescanning window (3 mm), implying that gating on its own for such cases would result in much longer treatment times. In addition, when rescanning is applied on its own, large differences between volumetric and layered rescanning have been observed as a function of increasing number of re-scans. However, once gating and rescanning is combined, HI to within 2% of the static plan could be achieved in the clinical target volume, with only moderately prolonged treatment times, irrespective of the rescanning strategy used. Moreover, these results are independent of the motion surrogate used. In conclusion, our results suggest image guided beam gating, combined with rescanning, is a feasible, effective and efficient motion mitigation approach for PBS-based liver tumour treatments.

Characteristics, home ranges and population estimates of narwhals (Monodon monoceros) around Baffin Island

Twenty-one narwhals tagged in 2003 and 2004 in Admiralty Inlet showed a different summer distributional pattern than previous narwhal-tracking studies from Somerset Island, Eclipse Sound and Melville Bay. The migration of the narwhals tracked from Admiralty Inlet moved out through Lancaster Sound 15 days earlier (P <0.0001) than the narwhals summering around Eclipse Sound, whereas the Admiralty Inlet narwhals reached the mouths of Eclipse Sound 18 days later (P <0.0001) than the Eclipse Sound summering population. The winter range of the Admiralty Inlet narwhals overlapped with the winter range of narwhals from Melville Bay and Eclipse Sound in central southern Baffin Bay and Northern Davis Strait, but not with the winter range of narwhals from Somerset Island that wintered further north. Distribution size of range, and population size did not appear to be related. An example of considerable year to year variation between area of summer and winter distribution in the 2 years was believed to be related to the sample size and number of pods of whales tagged, rather than to differences in sex or age classes.

Multiphase Buck Converter with Minimum Time Control Strategy for RF Envelope Modulation

Power amplifier supplied with constant supply voltage has very low efficiency in the transmitter. A DC-DC converter in series with a linear regulator can be used to obtain voltage modulation. Since this converter should be able to change the output voltage very fast, a multiphase buck converter with a minimum time control strategy is proposed. To modulate supply voltage of the envelope amplifier, the multiphase converter works with some particular duty cycle (i/n, i=1, 2 ... n, n is the number of phase) to generate discrete output voltages, and in these duty cycles the output current ripple can be completely cancelled. The transition times for the minimum time are pre-calculated and inserted in a look-up table. The theoretical background, the system model that is necessary in order to calculate the transition times and the experimental results obtained with a 4-phase buck prototype are given

An Interleaved EPE-Immune PA-DPL Structure for Resisting Concentrated EM Side Channel Attacks on FPGA Implementation

Early propagation effect (EPE) is a critical problem in conventional dual-rail logic implementations against Side Channel Attacks (SCAs). Among previous EPE-resistant architectures, PA-DPL logic offers EPE-free capability at relatively low cost. However, its separate dual core structure is a weakness when facing concentrated EM attacks where a tiny EM probe can be precisely positioned closer to one of the two cores. In this paper, we present an PA-DPL dual-core interleaved structure to strengthen resistance against sophisticated EM attacks on Xilinx FPGA implementations. The main merit of the proposed structure is that every two routing in each signal pair are kept identical even the dual cores are interleaved together. By minimizing the distance between the complementary routings and instances of both cores, even the concentrated EM measurement cannot easily distinguish the minor EM field unbalance. In PA- DPL, EPE is avoided by compressing the evaluation phase to a small portion of the clock period, therefore, the speed is inevitably limited. Regarding this, we made an improvement to extend the duty cycle of evaluation phase to more than 40 percent, yielding a larger maximum working frequency. The detailed design flow is also presented. We validate the security improvement against EM attack by implementing a simplified AES co-processor in Virtex-5 FPGA.

FPGA-Based Wireless Sensor Node Architecture for High Performance Applications

While for years traditional wireless sensor nodes have been based on ultra-low power microcontrollers with sufficient but limited computing power, the complexity and number of tasks of today’s applications are constantly increasing. Increasing the node duty cycle is not feasible in all cases, so in many cases more computing power is required. This extra computing power may be achieved by either more powerful microcontrollers, though more power consumption or, in general, any solution capable of accelerating task execution. At this point, the use of hardware based, and in particular FPGA solutions, might appear as a candidate technology, since though power use is higher compared with lower power devices, execution time is reduced, so energy could be reduced overall. In order to demonstrate this, an innovative WSN node architecture is proposed. This architecture is based on a high performance high capacity state-of-the-art FPGA, which combines the advantages of the intrinsic acceleration provided by the parallelism of hardware devices, the use of partial reconfiguration capabilities, as well as a careful power-aware management system, to show that energy savings for certain higher-end applications can be achieved. Finally, comprehensive tests have been done to validate the platform in terms of performance and power consumption, to proof that better energy efficiency compared to processor based solutions can be achieved, for instance, when encryption is imposed by the application requirements.

Wide bandwidth envelope trackers with reduced switching frequency for RF power amplifier

El requerimiento de proveer alta frecuencia de datos en los modernos sistema de comunicación inalámbricos resulta en complejas señales moduladas de radio-frequencia (RF) con un gran ancho de banda y alto ratio pico-promedio (PAPR). Para garantizar la linealidad del comportamiento, los amplificadores lineales de potencia comunes funcionan típicamente entre 4 y 10 dB de back-o_ desde la máxima potencia de salida, ocasionando una baja eficiencia del sistema. La eliminación y restauración de la evolvente (EER) y el seguimiento de la evolvente (ET) son dos prometedoras técnicas para resolver el problema de la eficiencia. Tanto en EER como en ET, es complicado diseñar un amplificador de potencia que sea eficiente para señales de RF de alto ancho de banda y alto PAPR. Una propuesta común para los amplificadores de potencia es incluir un convertidor de potencia de muy alta eficiencia operando a frecuencias más altas que el ancho de banda de la señal RF. En este caso, la potencia perdida del convertidor ocasionado por la alta frecuencia desaconseja su práctica cuando el ancho de banda es muy alto. La solución a este problema es el enfoque de esta disertación que presenta dos arquitecturas de amplificador evolvente: convertidor híbrido-serie con una técnica de evolvente lenta y un convertidor multinivel basado en un convertidor reductor multifase con control de tiempo mínimo. En la primera arquitectura, una topología híbrida está compuesta de una convertidor reductor conmutado y un regulador lineal en serie que trabajan juntos para ajustar la tensión de salida para seguir a la evolvente con precisión. Un algoritmo de generación de una evolvente lenta crea una forma de onda con una pendiente limitada que es menor que la pendiente máxima de la evolvente original. La salida del convertidor reductor sigue esa forma de onda en vez de la evolvente original usando una menor frecuencia de conmutación, porque la forma de onda no sólo tiene una pendiente reducida sino también un menor ancho de banda. De esta forma, el regulador lineal se usa para filtrar la forma de onda tiene una pérdida de potencia adicional. Dependiendo de cuánto se puede reducir la pendiente de la evolvente para producir la forma de onda, existe un trade-off entre la pérdida de potencia del convertidor reductor relacionada con la frecuencia de conmutación y el regulador lineal. El punto óptimo referido a la menor pérdida de potencia total del amplificador de evolvente es capaz de identificarse con la ayuda de modelo preciso de pérdidas que es una combinación de modelos comportamentales y analíticos de pérdidas. Además, se analiza el efecto en la respuesta del filtro de salida del convertidor reductor. Un filtro de dampeo paralelo extra es necesario para eliminar la oscilación resonante del filtro de salida porque el convertidor reductor opera en lazo abierto. La segunda arquitectura es un amplificador de evolvente de seguimiento de tensión multinivel. Al contrario que los convertidores que usan multi-fuentes, un convertidor reductor multifase se emplea para generar la tensión multinivel. En régimen permanente, el convertidor reductor opera en puntos del ciclo de trabajo con cancelación completa del rizado. El número de niveles de tensión es igual al número de fases de acuerdo a las características del entrelazamiento del convertidor reductor. En la transición, un control de tiempo mínimo (MTC) para convertidores multifase es novedosamente propuesto y desarrollado para cambiar la tensión de salida del convertidor reductor entre diferentes niveles. A diferencia de controles convencionales de tiempo mínimo para convertidores multifase con inductancia equivalente, el propuesto MTC considera el rizado de corriente por cada fase basado en un desfase fijo que resulta en diferentes esquemas de control entre las fases. La ventaja de este control es que todas las corrientes vuelven a su fase en régimen permanente después de la transición para que la siguiente transición pueda empezar muy pronto, lo que es muy favorable para la aplicación de seguimiento de tensión multinivel. Además, el control es independiente de la carga y no es afectado por corrientes de fase desbalanceadas. Al igual que en la primera arquitectura, hay una etapa lineal con la misma función, conectada en serie con el convertidor reductor multifase. Dado que tanto el régimen permanente como el estado de transición del convertidor no están fuertemente relacionados con la frecuencia de conmutación, la frecuencia de conmutación puede ser reducida para el alto ancho de banda de la evolvente, la cual es la principal consideración de esta arquitectura. La optimización de la segunda arquitectura para más alto anchos de banda de la evolvente es presentada incluyendo el diseño del filtro de salida, la frecuencia de conmutación y el número de fases. El área de diseño del filtro está restringido por la transición rápida y el mínimo pulso del hardware. La rápida transición necesita un filtro pequeño pero la limitación del pulso mínimo del hardware lleva el diseño en el sentido contrario. La frecuencia de conmutación del convertidor afecta principalmente a la limitación del mínimo pulso y a las pérdidas de potencia. Con una menor frecuencia de conmutación, el ancho de pulso en la transición es más pequeño. El número de fases relativo a la aplicación específica puede ser optimizado en términos de la eficiencia global. Otro aspecto de la optimización es mejorar la estrategia de control. La transición permite seguir algunas partes de la evolvente que son más rápidas de lo que el hardware puede soportar al precio de complejidad. El nuevo método de sincronización de la transición incrementa la frecuencia de la transición, permitiendo que la tensión multinivel esté más cerca de la evolvente. Ambas estrategias permiten que el convertidor pueda seguir una evolvente con un ancho de banda más alto que la limitación de la etapa de potencia. El modelo de pérdidas del amplificador de evolvente se ha detallado y validado mediante medidas. El mecanismo de pérdidas de potencia del convertidor reductor tiene que incluir las transiciones en tiempo real, lo cual es diferente del clásico modelos de pérdidas de un convertidor reductor síncrono. Este modelo estima la eficiencia del sistema y juega un papel muy importante en el proceso de optimización. Finalmente, la segunda arquitectura del amplificador de evolvente se integra con el amplificador de clase F. La medida del sistema EER prueba el ahorro de energía con el amplificador de evolvente propuesto sin perjudicar la linealidad del sistema. ABSTRACT The requirement of delivering high data rates in modern wireless communication systems results in complex modulated RF signals with wide bandwidth and high peak-to-average ratio (PAPR). In order to guarantee the linearity performance, the conventional linear power amplifiers typically work at 4 to 10 dB back-off from the maximum output power, leading to low system efficiency. The envelope elimination and restoration (EER) and envelope tracking (ET) are two promising techniques to overcome the efficiency problem. In both EER and ET, it is challenging to design efficient envelope amplifier for wide bandwidth and high PAPR RF signals. An usual approach for envelope amplifier includes a high-efficiency switching power converter operating at a frequency higher than the RF signal's bandwidth. In this case, the power loss of converter caused by high switching operation becomes unbearable for system efficiency when signal bandwidth is very wide. The solution of this problem is the focus of this dissertation that presents two architectures of envelope amplifier: a hybrid series converter with slow-envelope technique and a multilevel converter based on a multiphase buck converter with the minimum time control. In the first architecture, a hybrid topology is composed of a switched buck converter and a linear regulator in series that work together to adjust the output voltage to track the envelope with accuracy. A slow envelope generation algorithm yields a waveform with limited slew rate that is lower than the maximum slew rate of the original envelope. The buck converter's output follows this waveform instead of the original envelope using lower switching frequency, because the waveform has not only reduced slew rate but also reduced bandwidth. In this way, the linear regulator used to filter the waveform has additional power loss. Depending on how much reduction of the slew rate of envelope in order to obtain that waveform, there is a trade-off between the power loss of buck converter related to the switching frequency and the power loss of linear regulator. The optimal point referring to the lowest total power loss of this envelope amplifier is identified with the help of a precise power loss model that is a combination of behavioral and analytic loss model. In addition, the output filter's effect on the response is analyzed. An extra parallel damping filter is needed to eliminate the resonant oscillation of output filter L and C, because the buck converter operates in open loop. The second architecture is a multilevel voltage tracking envelope amplifier. Unlike the converters using multi-sources, a multiphase buck converter is employed to generate the multilevel voltage. In the steady state, the buck converter operates at complete ripple cancellation points of duty cycle. The number of the voltage levels is equal to the number of phases according the characteristics of interleaved buck converter. In the transition, a minimum time control (MTC) for multiphase converter is originally proposed and developed for changing the output voltage of buck converter between different levels. As opposed to conventional minimum time control for multiphase converter with equivalent inductance, the proposed MTC considers the current ripple of each phase based on the fixed phase shift resulting in different control schemes among the phases. The advantage of this control is that all the phase current return to the steady state after the transition so that the next transition can be triggered very soon, which is very favorable for the application of multilevel voltage tracking. Besides, the control is independent on the load condition and not affected by the unbalance of phase current. Like the first architecture, there is also a linear stage with the same function, connected in series with the multiphase buck converter. Since both steady state and transition state of the converter are not strongly related to the switching frequency, it can be reduced for wide bandwidth envelope which is the main consideration of this architecture. The optimization of the second architecture for wider bandwidth envelope is presented including the output filter design, switching frequency and the number of phases. The filter design area is restrained by fast transition and the minimum pulse of hardware. The fast transition needs small filter but the minimum pulse of hardware limitation pushes the filter in opposite way. The converter switching frequency mainly affects the minimum pulse limitation and the power loss. With lower switching frequency, the pulse width in the transition is smaller. The number of phases related to specific application can be optimized in terms of overall efficiency. Another aspect of optimization is improving control strategy. Transition shift allows tracking some parts of envelope that are faster than the hardware can support at the price of complexity. The new transition synchronization method increases the frequency of transition, allowing the multilevel voltage to be closer to the envelope. Both control strategies push the converter to track wider bandwidth envelope than the limitation of power stage. The power loss model of envelope amplifier is detailed and validated by measurements. The power loss mechanism of buck converter has to include the transitions in real time operation, which is different from classical power loss model of synchronous buck converter. This model estimates the system efficiency and play a very important role in optimization process. Finally, the second envelope amplifier architecture is integrated with a Class F amplifier. EER system measurement proves the power saving with the proposed envelope amplifier without disrupting the linearity performance.

Pulse-Shape Analysis of PDM-QPSK Modulation Formats for 100 and 200 Gb/s DWDM transmissions

Advanced optical modulation format polarization-division multiplexed quadrature phase shift keying (PDM-QPSK) has become a key ingredient in the design of 100 and 200-Gb/s dense wavelength-division multiplexed (DWDM) networks. The performance of this format varies according to the shape of the pulses employed by the optical carrier: non-return to zero (NRZ), return to zero (RZ) or carrier-suppressed return to zero (CSRZ). In this paper we analyze the tolerance of PDM-QPSK to linear and nonlinear optical impairments: amplified spontaneous emission (ASE) noise, crosstalk, distortion by optical filtering, chromatic dispersion (CD), polarization mode dispersion (PMD) and fiber Kerr nonlinearities. RZ formats with a low duty cycle value reduce pulse-to-pulse interaction obtaining a higher tolerance to CD, PMD and intrachannel nonlinearities.