Influence of process parameters on fluidised hot-melt granulation and tablet pressing of pharmaceutical powders

This study investigates the influence of process parameters on the fluidised hot melt granulation of lactose and PEG 6000, and the subsequent tablet pressing of the granules. Granulation experiments were performed to assess the effect of granulation time and binder content of the feed on the resulting granule properties such as mass mean granule size, size distribution, granule fracture stress, and granule porosity. These data were correlated using the granule growth regime model. It was found that the dominant granule growth mechanisms in this melt granulation system were nucleation followed by steady growth (PEG 10–20% w/w). However, with binder contents greater than 20% w/w, the granulation mechanism moved to the “over-wet massing” regime in which discrete granule formation could not be obtained. The granules produced in the melt fluidised bed process were subsequently pressed into tablets using an industrial tablet press. The physical properties of the tablets: fracture stress, disintegration time and friability were assessed using industry standards. These analyses indicated that particle size and binder content of the initial granules influenced the mechanical properties of the tablets. It was noted that a decrease in initial granule size resulted in an increase in the fracture stress of the tablets formed.

Mineralogical characteristics and transformations during long-term operation of a zero-valent iron reactive barrier

Received for publication October 31, 2002. Design and operation of Fe0 permeable reactive barriers (PRBs) can be improved by understanding the long-term mineralogical transformations that occur within PRBs. Changes in mineral precipitates, cementation, and corrosion of Fe0 filings within an in situ pilot-scale PRB were examined after the first 30 months of operation and compared with results of a previous study of the PRB conducted 15 months earlier using X-ray diffraction and scanning electron microscopy employing energy dispersive X-ray and backscatter electron analyses. Iron (oxy)hydroxides, aragonite, and maghemite and/or magnetite occurred throughout the cores collected 30 mo after installation. Goethite, lepidocrocite, mackinawite, aragonite, calcite, and siderite were associated with oxidized and cemented areas, while green rusts were detected in more reduced zones. Basic differences from our last detailed investigation include (i) mackinawite crystallized from amorphous FeS, (ii) aragonite transformed into calcite, (iii) akaganeite transformed to goethite and lepidocrocite, (iv) iron (oxy)hydroxides and calcium and iron carbonate minerals increased, (v) cementation was greater in the more recent study, and (vi) oxidation, corrosion, and disintegration of Fe0 filings were greater, especially in cemented areas, in the more recent study. If the degree of corrosion and cementation that was observed from 15 to 30 mo after installation continues, certain portions of the PRB (i.e., up-gradient entrance of the ground water to the Fe0 section of the PRB) may last less than five more years, thus reducing the effectiveness of the PRB to mitigate contaminants. Abbreviations: EDX, energy dispersive X-ray • Fe0, zerovalent iron • PRB, permeable reactive barrier • SEM, scanning electron microscopy • XRD, X-ray diffraction

Chitosan nanoparticle as protein delivery carrier - Systematic examination of fabrication conditions for efficient loading and release

Chitosan nanoparticles fabricated via different preparation protocols have been in recent years widely studied as carriers for therapeutic proteins and genes with varying degree of effectiveness and drawbacks. This work seeks to further explore the polyionic coacervation fabrication process, and associated processing conditions under which protein encapsulation and subsequent release can be systematically and predictably manipulated so as to obtain desired effectiveness. BSA was used as a model protein which was encapsulated by either incorporation or incubation method, using the polyanion tripolyphosphate (TPP) as the coacervation crosslink agent to form chitosan-BSA-TPP nanoparticles. The BSA-loaded chitosan-TPP nanoparticles were characterized for particle size, morphology, zeta potential, BSA encapsulation efficiency, and subsequent release kinetics, which were found predominantly dependent on the factors of chitosan molecular weight, chitosan concentration, BSA loading concentration, and chitosan/TPP mass ratio. The BSA loaded nanoparticles prepared under varying conditions were in the size range of 200-580 nm, and exhibit a high positive zeta potential. Detailed sequential time frame TEM imaging of morphological change of the BSA loaded particles showed a swelling and particle degradation process. Initial burst released due to surface protein desorption and diffusion from sublayers did not relate directly to change of particle size and shape, which was eminently apparent only after 6 h. It is also notable that later stage particle degradation and disintegration did not yield a substantial follow-on release, as the remaining protein molecules, with adaptable 3-D conformation, could be tightly bound and entangled with the cationic chitosan chains. In general, this study demonstrated that the polyionic coacervation process for fabricating protein loaded chitosan nanoparticles offers simple preparation conditions and a clear processing window for manipulation of physiochemical properties of the nanoparticles (e.g., size and surface charge), which can be conditioned to exert control over protein encapsulation efficiency and subsequent release profile. The weakness of the chitosan nanoparticle system lies typically with difficulties in controlling initial burst effect in releasing large quantities of protein molecules. (C) 2007 Elsevier B.V. All rights reserved.

A Geostatistical Investigation into Changing Permeability of Sandstones During Weathering Simulations

The ability to predict the behavior of masonry materials is crucial to conserve building stone. Natural stone, such as sandstone, is not immune from the processes of weathering in the built environment and suffers from decay by granular disintegration, contour scaling, and multiple flaking. Spatial variation of rock properties is a major contributing factor to inconsistent responses to weathering. This has implications for moisture movement and salt input and output and storage, and results in unpredictability in the decay dynamics of masonry materials. This article explores the use of variography and kriging to investigate the spatial interactions between the trigger factors of stone decay, in particular, permeability and its effect on salt penetration. Sandstone blocks were used to represent fresh building stones from a weathering perspective and gave baseline characteristics for the interpretation of subsequent deterioration and decay pathways. Simulated weathering trials involved preloading a sandstone block with salt and subjecting a separate block to 20 cycles of a weathering trial designed to simulate a temperate weathering regime. Geostatistical analysis indicated differences in the spatial variation of permeability of the fresh rock and that subjected to the weathering regimes. Spatial prediction and visualization showed differences in the spatial continuity of permeability in a horizontal and vertical direction through the preloaded block after salt weathering. Continual wetting with salt and alternate heating increased permeability in a vertical direction, enabling the ingress and movement of salt and moisture more effectively through the stone.

Micro-environmental change as a trigger for granite decay in offshore Irish lighthouses: implications for the long-term preservation of operational historic buildings.

Following automation of lighthouses around the coastline of Ireland, reports of accelerated deterioration of interior granite stonework have increased significantly with an associated deterioration in the historic structure and rise in related maintenance costs. Decay of granite stone- work primarily occurs through granular disintegration with the effective grusification of granite surfaces. A decay gradient exists within the towers whereby the condition of granite in the lower levels is much worse than elsewhere. The lower tower levels are also regions with highest rela- tive humidity values and greatest salt concentrations. Data indicate that post-automation decay may have been trig- gered by a change in micro-environmental conditions within the towers associated with increased episodes of condensation on stone surfaces. This in turn appears to have facilitated deposition and accumulation of hygro- scopic salts (e.g. NaCl) giving rise to widespread evidence of deliquescence in the lower tower levels. Evidence indicates that the main factors contributing to accelerated deterioration of interior granite stonework are changes in micro-environmental conditions, salt weathering, chemical weathering through the corrosive effect of strongly alkaline conditions on alumino-silicate minerals within the granite and finally, the mica-rich characteristics of the granite itself which increases its structural and chemical susceptibility to subaerial weathering processes by creating points of weakness within the granite. This case study demonstrates how seemingly minor changes in micro-environmental conditions can unintentionally trigger the rapid and extensive deterioration of a previously stable rock type and threaten the long-term future of nationally iconic opera- tional historic structures.

Physicochemical characterization and preliminary in vivo efficacy of bioadhesive, semisolid formulations containing flurbiprofen for the treatment of gingivitis

In this study, the physicochemical properties and preliminary in vivo clinical performance of formulations containing hydroxyethylcellulose (HEC; 3, 5, 10% w/w, poly(vinylpyrrolidone) (PVP; 3, 5% w/w), polycarbophil (PC; 1, 3, 5% w/w), and flurbiprofen (5% w/w) were examined. Flurbiprofen release into PBS pH 7.4 was performed at 37 degrees C. The mechanical properties (hardness, compressibility, adhesiveness, initial stress) and syringeability of formulations were determined using a texture analyzer in texture profile analysis (TPA) and compression modes, respectively. In general, the time required for release of 10 and 30% of the original mass of flurbiprofen (t(10%), t(30%)) increased as the concentration of each polymeric component increased. However, in the presence of either 5 or 10% HEC and 5% PC, increased PVP concentration decreased both t(10%), t(30%) due to excessive swelling land disintegration) of these formulations. Increased concentrations of HEC, PVP, and PC significantly increased formulation hardness, compressibility, work of syringe expression, and initial stress due to the effects of these polymers on formulation viscoelasticity. Similarly, increased concentrations of PC (primarily), HEC, and PVP increased formulation adhesiveness-due to the known bioadhesive properties of these polymers. Clinical efficacies of formulations containing 3% HEC, 3% PVP, 3% PC, and either 0% (control) of 5% (test) flurbiprofen, selected to offer optimal drug release and mechanical properties, were evaluated and clinically compared in an experimental gingivitis model. The test (flurbiprofen-containing) formulation significantly reduced gingival inflammation, as evaluated using the gingival index, and the gingival crevicular fluid volume, whereas, these clinical parameters were generally increased in volunteers who had received the control formulation. There were no observed differences in the plaque indices of the two subject groups, confirming that the observed differences in gingival inflammation could not be accredited to differences in plaque accummulation. This study has shown both the applicability of the in vitro methods used, particularly TPA, for the rational selection of formulations for clinical evaluation and, additionally, the clinical benefits of the topical application of a bioadhesive semisolid flurbiprofen-containing formulation for the treatment of experimental gingivitis.

Arsenic-speciation in arsenate-resistant and non-resistant populations of the earthworm, Lumbricus rubellus

Arsenic speciation was determined in Lumbricus rubellus Hoffmeister from arsenic-contaminated mine spoil sites and an uncontaminated site using HPLC-MS, HPLC-ICP-MS and XAS. It was previously demonstrated that L. rubellus from mine soils were more arsenate resistant than from the uncontaminated site and we wished to investigate if arsenic speciation had a role in this resistance. Earthworms from contaminated sites had considerably higher arsenic body burdens (maximum 1,358 mg As kg-1) compared to the uncontaminated site (maximum 13 mg As kg-1). The only organo-arsenic species found in methanol/water extracts for all earthworm populations was arsenobetaine, quantified using both HPLC-MS and HPLC-ICP-MS. Arsenobetaine concentrations were high in L. rubellus from the uncontaminated site when concentrations were expressed as a percentage of the total arsenic burden (23% mean), but earthworms from the contaminated sites with relatively low arsenic burdens also had these high levels of arsenobetaine (17% mean). As arsenic body burden increased, the percentage of arsenobetaine present decreased in a dose dependent manner, although its absolute concentration rose with increasing arsenic burden. The origin of this arsenobetaine is discussed. XAS analysis of arsenic mine L. rubellus showed that arsenic was primarily present as As(III) co-ordinated with sulfur (30% approx.), with some As(v) with oxygen (5%). Spectra for As(III) complexed with glutathione gave a very good fit to the spectra obtained for the earthworms, suggesting a role for sulfur co-ordination in arsenic metabolism at higher earthworm arsenic burdens. It is also possible that the disintegration of As(III)-S complexes may have taken place due to (a) processing of the sample, (b) storage of the extract or (c) HPLC anion exchange. HPLC-ICP-MS analysis of methanol extracts showed the presence of arsenite and arsenate, suggesting that these sulfur complexes disintegrate on extraction. The role of arsenic speciation in the resistance of L. rubellus to arsenate is considered.

Mineralogical Characteristics and Transformations during Long-Term Operation of a Zerovalent Iron Reactive Barrier

Design and operation of Fe⁰ permeable reactive barriers (PRBs) can be improved by understanding the long-term mineralogical transformations that occur within PRBs. Changes in mineral precipitates, cementation, and corrosion of Fe⁰ filings within an in situ pilot-scale PRB were examined after the first 30 months of operation and compared with results of a previous study of the PRB conducted 15 months earlier using X-ray diffraction and scanning electron microscopy employing energy dispersive X-ray and backscatter electron analyses. Iron (oxy)hydroxides, aragonite, and maghemite and/or magnetite occurred throughout the cores collected 30 mo after installation. Goethite, lepidocrocite, mackinawite, aragonite, calcite, and siderite were associated with oxidized and cemented areas, while green rusts were detected in more reduced zones. Basic differences from our last detailed investigation include (i) mackinawite crystallized from amorphous FeS, (ii) aragonite transformed into calcite, (iii) akaganeite transformed to goethite and lepidocrocite, (iv) iron (oxy)hydroxides and calcium and iron carbonate minerals increased, (v) cementation was greater in the more recent study, and (vi) oxidation, corrosion, and disintegration of Fe⁰ filings were greater, especially in cemented areas, in the more recent study. If the degree of corrosion and cementation that was observed from 15 to 30 mo after installation continues, certain portions of the PRB (i.e., up-gradient entrance of the ground water to the Fe⁰ section of the PRB) may last less than five more years, thus reducing the effectiveness of the PRB to mitigate contaminants.

Release of β-galactosidase from poloxamine/α-cyclodextrin hydrogels

All mammals lose their ability to produce lactase (β-galactosidase), the enzyme that cleaves lactose into galactose and glucose, after weaning. The prevalence of lactase deficiency (LD) spans from 2 to 15% among northern Europeans, to nearly 100% among Asians. Following lactose consumption, people with LD often experience gastrointestinal symptoms such as abdominal pain, bowel distension, cramps and flatulence, or even systemic problems such as headache, loss of concentration and muscle pain. These symptoms vary depending on the amount of lactose ingested, type of food and degree of intolerance. Although those affected can avoid the uptake of dairy products, in doing so, they lose a readily available source of calcium and protein. In this work, gels obtained by complexation of Tetronic 90R4 with α-cyclodextrin loaded with β-galactosidase are proposed as a way to administer the enzyme immediately before or with the lactose-containing meal. Both molecules are biocompatible, can form gels in situ, and show sustained erosion kinetics in aqueous media. The complex was characterized by FTIR that evidenced an inclusion complex between the polyethylene oxide block and α-cyclodextrin. The release profiles of β-galactosidase from two different matrices (gels and tablets) of the in situ hydrogels have been obtained. The influence of the percentage of Tetronic in media of different pH was evaluated. No differences were observed regarding the release rate from the gel matrices at pH 6 (t50 = 105 min). However, in the case of the tablets, the kinetics were faster and they released a greater amount of 90R4 (25%, t50 = 40–50 min). Also, the amount of enzyme released was higher for mixtures with 25% Tetronic. Using suitable mathematical models, the corresponding kinetic parameters have been calculated. In all cases, the release data fit quite well to the Peppas–Sahlin model equation, indicating that the release of β-galactosidase is governed by a combination of diffusion and erosion processes. It has been observed that the diffusion mechanism prevails over erosion during the first 50 minutes, followed by continued release of the enzyme due to the disintegration of the matrix.

Electrical conduction and rheological behaviour of composites of poly(epsilon-caprolactone) and MWCNTs

Two mechanisms of conduction were identified from temperature dependent (120 K-340 K) DC electrical resistivity measurements of composites of poly(c-caprolactone) (PCL) and multi-walled carbon nanotubes (MWCNTs). Activation of variable range hopping (VRH) occurred at lower temperatures than that for temperature fluctuation induced tunneling (TFIT). Experimental data was in good agreement with the VRH model in contrast to the TFIT model, where broadening of tunnel junctions and increasing electrical resistivity at T > T-g is a consequence of a large difference in the coefficients of thermal expansion of PCL and MWCNTs. A numerical model was developed to explain this behavior accounting for a thermal expansion effect by supposing the large increase in electrical resistivity corresponds to the larger relative deformation due to thermal expansion associated with disintegration of the conductive MWCNT network. MWCNTs had a significant nucleating effect on PCL resulting in increased PCL crystallinity and an electrically insulating layer between MWCNTs. The onset of rheological percolation at similar to 0.18 vol% MWCNTs was clearly evident as storage modulus, G' and complex viscosity, vertical bar eta*vertical bar increased by several orders of magnitude. From Cole-Cole and Van Gurp-Palmen plots, and extraction of crossover points (G(c)) from overlaying plots of G' and G '' as a function of frequency, the onset of rheological percolation at 0.18 vol% MWCNTs was confirmed, a similar MWCNT loading to that determined for electrical percolation. 

The effect of heating temperature on the properties of vermiculites from Tanzania with respect to potential agronomic applications

This study was carried out to assess the properties of vermiculites from Tanzania with respect to the temperature used to expand them. Vermiculites from five locations in the Mozambique Belt of Tanzania were sampled and heated at 15, 200, 400, 600 and 800 °C in a muffle furnace. Palabora Europe Ltd provided one sample for comparison from their South Africa deposit which provides vermiculite used worldwide as a soil amendment. Water release characteristic, cation exchange capacity, pH, mass loss, and bulk density were among the properties assessed. All six vermiculites responded differently on heating, and had a significant variation in their agronomic properties. Water release characteristic varied with the degree of exfoliation and phase composition. Although vermiculites from Tanzania expanded on heating, their capacity to retain plant available water was relatively low as compared to vermiculite from Palabora. Disintegration on heating and the presence of a high amount of iron could be among the factors affecting their water release characteristic. Loss of hydroxyl water was higher in vermiculites than in hydrobiotites. Dehydroxylation enhanced the availability of exchangeable K⁺ and reduced significantly the cation exchange capacity of vermiculites. The optimum exchangeable K⁺ was obtained on heating at a temperature of 600 °C. The pH was unaffected by heating to a temperature of less than 600 °C. At higher temperature, the pH increased in some samples and was accompanied by substantial amounts of exchangeable Mg²⁺. Thus, it was concluded that initial characterization of vermiculites is essential prior to potential agricultural applications in order to optimize their agronomic potential. © 2008 Elsevier B.V. All rights reserved.

Microphytobenthos vs Hydrobia: trophic coupling in estuarine environment

Os estuários são ambientes complexos, biologicamente diversos e muito importantes no que respeita à produtividade primária. As zonas intertidais destes ecossistemas são ocupadas por organismos que possuem uma elevada capacidade de sobrevivência e adaptação face às variadas e rápidas alterações nos factores ambientais (tais como temperatura, salinidade, conteúdo hídrico, etc.). As cadeias tróficas com origem no ecossistema estuarino bentónico são essencialmente herbívoras, regulando o fluxo de energia desde o fundo sedimentar e através do ecossistema. Nas áreas estuarinas intertidais a produção primária é essencialmente suportada pelo microfitobentos (MPB). Estas comunidades de microalgas bênticas constituem uma importante fonte de matéria orgânica e são por si só a principal fonte alimentar para as populações de Hydrobia. Neste contexto, a interacção MPB - Hydrobia é um modelo-chave na investigação da cadeia trófica estuarina de origem bentónica, actuando como um importante canal de transporte de energia para os níveis tróficos superiores, especialmente se considerarmos que Hydrobia é uma importante presa para peixes, aves e caranguejos. O presente estudo tem por objectivos gerais: i) a investigação do controlo ambiental (particularmente da luz e do teor em água do sedimento) e endógeno na migração vertical do MPB e ii) a identificação e potencial utilização de marcadores tróficos (pigmentos e ácidos gordos) úteis à investigação da interacção MPB – Hydrobia em laboratório e em condições naturais, considerando a existência de uma elevada plasticidade trófica por parte da Hydrobia e a elevada densidade populacional que estes organismos podem apresentar. A primeira fase de investigação resultou na comparação do papel dos estímulos ambientais e do controlo endógeno nos padrões de comportamento migratório vertical do microfitobentos, demonstrando a existência de um controlo essencialmente endógeno na formação e desintegração do biofilme superficial. A regulação e manutenção da biomassa à superfície do sedimento são claramente controladas pela variação dos factores ambientais, em especial da luz, cuja presença é essencial à formação total do biofilme microalgal à superfície do sedimento intertidal. Foi proposta uma nova abordagem metodológica com vista à estimativa nãodestrutiva do teor de água de sedimentos intertidais vasosos , possibilitando o estudo da influência da acção do vento no conteúdo hídrico dos sedimentos e o consequente impacto da dessecação na comunidade microfitobêntica. Observou-se que a dessecação provoca efeitos limitantes não só na biomassa superficial mas também na actividade fotossintética dos biofilmes microfitobênticos, conduzindo à diminuição da produtividade primária. No que respeita à dinâmica trófica da interacção MPB - Hydrobia foi estabelecido o uso do pigmento feoforbide a, quantificado nas partículas fecais da fauna, como marcador trófico que permite estimar a quantidade de biomassa de microalgas (clorofila a) incorporada pelos organismos animais.Para tal foi investigada e comprovada a existência de uma relação significativa entre a concentração de feopigmentos excretados e a concentração de clorofila a ingerida. Estes estudos foram desenvolvidos numa primeira fase à escala diária, considerando os efeitos dos ciclos sazonais, dia-noite e maré, e depois com a validação em condições naturais, numa escala mensal. A taxa de ingestão média de indivíduos de H. ulvae varia ao longo do dia, com o máximo em torno dos períodos diurnos de maré baixa, o que pode estar relacionado com a disponibilidade de MPB. As taxas de ingestão (TI) de H. ulvae variam ainda em função da estação do ano (TI verão > TI primavera) e em função da densidade de indivíduos (> densidade, < ingestão). Verificou-se um efeito negativo na concentração de clorofila disponível após herbívoria independentemente da densidade de indivíduos. Finalmente, a comparação dos perfis de ácidos gordos de H. ulvae provenientes de diferentes habitats com os perfis de potenciais fontes alimentares permitiu demonstrar que os ácidos gordos são ferramentas úteis na identificação do habitat ocupado por estes organismos. No entanto, apesar da ocupação de diferentes habitats e da integração de múltiplas fontes de produção primária na sua dieta foram sempre observados significativos níveis de ácidos gordos específicos de microalgas (em particular diatomáceas), reforçando o papel importante das comunidades de microalgas bênticas na dieta das populações de H. ulvae.

Percepção e valores das comunidades tradicionais no processo de desenvolvimento

Esta tese constitui uma reflexão sobre uma realidade, a praia do Francês, Alagoas, Brasil, que após mais de uma década é agora revisitada demonstrando os impactos socioambientais evidenciados ao longo de 30 anos, e por sua vez, fazem com que esta praia se transforme em laboratório cuja análise desenvolvida poderá servir como exemplo para ações futuras, e sustentáveis, em outras localidades. Sobretudo para áreas encontradas no mundo periférico, subdesenvolvido ou no Sul do Mundo, caracterizadas pela presença de populações tradicionais com seu rico e variado conhecimento, oralmente transmitido, adquirido através de suas observações práticas e cotidianas com seu meio circundante. Porém, este conhecimento encontra-se ameaçado pelo atual padrão de modernização, homogeneização do mundo, que em seu processo de desenvolvimento exclui crenças, valores e percepções de comunidades tradicionais inteiras, uma vez que se caracteriza por ocorrer com ausência de um olhar atento as especificidades locais, onde estas populações são as primeiras a sofrer com o atual modelo imposto que as ignora por completo e, ao mesmo tempo, por ocorrer com anuência do poder público local. Ao ignorá-las, tais ações minam suas formas de subsistência e via de consequência, às exclui das áreas onde sempre viveram e preservaram fazendo com que um importante e aprofundado conhecimento se perca, juntamente com a desintegração de seus laços de sociabilidade. A exemplo do Arquipélago dos Bijagós, Guiné-Bissau, costa Atlântica da África, lugar de existência de importante população tradicional que, a exemplo de outras localidades do mundo periférico, começa a experimentar transformações em seu patrimônio natural e cultural, decorrentes de ações desconectadas da realidade local. Este estudo, acena para uma importante reflexão sobre os impactos observados nesta realidade e os evidenciados na Praia do Francês. Portanto, procura-se aqui demonstrar a importância do conhecimento e das práticas existentes nas populações tradicionais (autóctones) para ações futuras, onde a inclusão deste saber seja prioridade para outras formas de pensar o desenvolvimento; e em seu processo de construção/planejamento este ocorra: com base no respeito à diversidade e com a participação dos mais diferentes e importantes atores. Enfim, um processo de desenvolvimento de base local, endógeno, sustentável.

Aims of education and well-being as absence of disorder

This thesis offers an original account of what personal well-being can be. Any account of education, it is believed, has to do with and aims at personal well-being. I approach this view on well-being not in a positive but in a negative way. I put forward some items that in certain circumstances can be taken by and called sources or forms of disorder. In the absence of such forms or sources of disorder, I assume that a certain order, prudential or moral, takes place and that constitutes the well-being of the person. The concept of ‘absence of disorder’ is introduced and argued as an educationally appropriate view of personal well-being which is the central educational aim. Therefore, ‘absence of disorder’ is positioned as the central aim of education. This concept is illuminated, for practical reasoning, by a list of seven possible forms of disorder: Comparison, Corruption, Dependency, Division, Fear, Self-disintegration and Violence. As a view of personal well-being, ‘absence of disorder’ is initially rooted in informed desire satisfaction, via the introduction of the concept of entropy. Prudentially, the agent’s informed desire is satisfied by living a life with low build up of entropy or disorder. But, in a second move such a base is also provided by the Levinasinian concept of ‘disinterest’ as a root for ‘what is to be a human’. Such ‘disinterest’ is related to the concepts of love and of ‘action for its own sake’. It is at this final approach that an attempt is made towards the approximation of the ethical and the prudential aspects of social practices. Even if only to some extent successful, the argument is directed to the following conclusion: an education aiming at ‘absence of disorder’ may promote prudential well-being and give us some confidence in simultaneously favouring moral education.