Direct detection of Mycoplasma bovis in milk and tissue samples by real-time PCR

Bovine mastitis caused by Mycoplasma bovis is of great economic importance to the beef and dairy industry. Here we describe a new specific real-time PCR assay targeting the uvrC gene that was developed to directly detect M. bovis from milk and tissue samples without laborious DNA purification.

A quantitative phenytoin GC-MS method and it's validation for samples from human ex situ brain microdialysis, blood and saliva using solid-phase extraction

This study describes the development and validation of a gas chromatography-mass spectrometry (GC-MS) method to identify and quantitate phenytoin in brain microdialysate, saliva and blood from human samples. A solid-phase extraction (SPE) was performed with a nonpolar C8-SCX column. The eluate was evaporated with nitrogen (50°C) and derivatized with trimethylsulfonium hydroxide before GC-MS analysis. As the internal standard, 5-(p-methylphenyl)-5-phenylhydantoin was used. The MS was run in scan mode and the identification was made with three ion fragment masses. All peaks were identified with MassLib. Spiked phenytoin samples showed recovery after SPE of ≥94%. The calibration curve (phenytoin 50 to 1,200 ng/mL, n = 6, at six concentration levels) showed good linearity and correlation (r² > 0.998). The limit of detection was 15 ng/mL; the limit of quantification was 50 ng/mL. Dried extracted samples were stable within a 15% deviation range for ≥4 weeks at room temperature. The method met International Organization for Standardization standards and was able to detect and quantify phenytoin in different biological matrices and patient samples. The GC-MS method with SPE is specific, sensitive, robust and well reproducible, and is therefore an appropriate candidate for the pharmacokinetic assessment of phenytoin concentrations in different human biological samples.

Direct visualization of solute locations in laboratory ice samples, links to videos

Many important chemical reactions occur in polar snow, where solutes may be present in several reservoirs, including at the air-ice interface and in liquid-like regions within the ice matrix. Some recent laboratory studies suggest chemical reaction rates may differ in these two reservoirs. While investigations have examined where solutes are found in natural snow and ice, similar research has not identified solute locations in laboratory samples, nor the possible factors controlling solute segregation. To address this, we examined solute locations in ice samples prepared from either aqueous cesium chloride (CsCl) or Rose Bengal solutions that were frozen using several different methods. Samples frozen in a laboratory freezer had the largest liquid-like inclusions and air bubbles, while samples frozen in a custom freeze chamber had somewhat smaller air bubbles and inclusions; in contrast, samples frozen in liquid nitrogen showed much smaller concentrated inclusions and air bubbles, only slightly larger than the resolution limit of our images (~2 µm). Freezing solutions in plastic versus glass vials had significant impacts on the sample structure, perhaps because the poor heat conductivity of plastic vials changes how heat is removed from the sample as it cools. Similarly, the choice of solute had a significant impact on sample structure, with Rose Bengal solutions yielding smaller inclusions and air bubbles compared to CsCl solutions frozen using the same method. Additional experiments using higher-resolution imaging of an ice sample show that CsCl moves in a thermal gradient, supporting the idea that the solutes in ice are present in liquid-like regions. Our work shows that the structure of laboratory ice samples, including the location of solutes, is sensitive to freezing method, sample container, and solute characteristics, requiring careful experimental design and interpretation of results.

Pore water and solid phase sulfur, carbon and iron data from samples collected in the Argentine Basin during expedition M78

Sulfur phases in the Argentine Basin.

Effect of lactose solid-state on the aerosolization performance of drug-carrier mixtures

Lactose, in particular α-lactose monohydrate, is the most used carrier for inhalation. Its surface and solid-state properties are of paramount importance in determining drug aerosolization performance. However, these properties may be altered by processing, such as micronization, thus affecting the product performance and stability. The present research project focused on the study of the effect of lactose solid-state on the aerosolization performance of drug-carrier mixtures, giving particular attention to the impact of micronization on lactose physico-chemical properties. The formation of a fraction of hygroscopic anhydrous α-lactose, rather than amorphous lactose, as a consequence of the mechanical stress stemming from micronization was evidenced by 1H NMR, XRPD and DSC analyses performed on samples of micronized lactose. The development of a new DVS method capable to identify and quantify different forms of α-lactose (hygroscopic anhydrous, stable anhydrous and amorphous), even simultaneously present in the same sample, confirmed the results obtained with the above-mentioned techniques. The influence of lactose solid-state on drug respirability was then evaluated through the preparation and in vitro aerodynamic assessment of ternary and binary mixtures containing two different drugs. In particular, the use, as carriers, of anhydrous forms of α-lactose in place of the conventional α-lactose monohydrate resulted in significantly improved respirability in the case of salbutamol sulphate and poorer performance in the case of budesonide. In an attempt to rationalize the obtained results, IGC was selected as a tool to investigate possible variations in the surface energy of the studied lactose carriers and APIs. A direct correlation between the total surface free energy of lactose carriers and drug respirability was not found. However, salbutamol sulphate and budesonide exhibited different specific surface free energy, to which the difference in the aerosolization performance may be, at least in part, ascribed.

Unit maintenance, direct support, and general support maintenance repair parts and special tools lists : truck, lift, fork, electric, solid rubber tires, 2,000 pound capacity, Army model MHE-197, Baker model FTD-020-EE, NSN 3930-00-724-4058, 100 in. lift ....

"August 1992."

Unit, direct support, and general support maintenance repair parts and special tools lists : truck, forklift, electric, solid rubber tires, 6000 lb capacity, 180 in. lift (Drexel Dynamics model FL60-EE5600) (Army model MHE206), NSN 3930-00-935-7867.

"November 1992."

Direct support and general support maintenance repair parts and special tools lists : truck, lift, fork, gasoline, solid rubber tired wheels, 2000 lbs capacity Army model MHE 182, NSN 3930-00-958-3682, Allis-Chalmers model FT20-24PS-100 and NSN 3930-00-958-3683, Allis-Chalmers model FT20-24PS-127.

"January 1984."