Constitutive Model for Strength Characteristics of Municipal Solid Waste

This paper presents modification of the derivation of a previously proposed constitutive model for the prediction of stress-strain behavior of municipal solid waste (MSW) incorporating different mechanisms, such as immediate compression under loading, mechanical creep, and time-dependent biodegradation effect. The model is based on critical state soil mechanics incorporating increments in volumetric strains because of elastic, plastic, creep, and biodegradation effects. The improvement introduced in this paper is the modified critical state surface and considers five variable parameters for the estimation of stress-strain behavior of MSW under different loading conditions. In addition, an expression for the strain hardening rule is derived, with considerations of time-dependent mechanical creep and biodegradation effects. The model is validated using results from experimental studies and data from published literature. The results are also compared with the predictions of the stress-strain response obtained from a well-established hyperbolic model. (c) 2014 American Society of Civil Engineers.

A model supersonic buried-nozzle jet: instability and acoustic wave scattering and the far-field sound

We consider sound source mechanisms involving the acoustic and instability modes of dual-stream isothermal supersonic jets with the inner nozzle buried within an outer shroud-like nozzle. A particular focus is scattering into radiating sound waves at the shroud lip. For such jets, several families of acoustically coupled instability waves exist, beyond the regular vortical Kelvin-Helmholtz mode, with different shapes and propagation characteristics, which can therefore affect the character of the radiated sound. In our model, the coaxial shear layers are vortex sheets while the incident acoustic disturbances are the propagating shroud modes. The Wiener-Hopf method is used to compute their scattering at the sharp shroud edge to obtain the far-field radiation. The resulting far-field directivity quantifies the acoustic efficiency of different mechanisms, which is particularly important in the upstream direction, where the results show that the scattered sound is more intense than that radiated directly by the shear-layer modes.

Effect of H-2/CO Composition on Extinction Strain Rates of Counterflow Syngas Flames

This work presents a detailed experimental and numerical investigation of the effect of H-2/CO composition on extinction characteristics of premixed and nonpremixed syngas flames. Experimental measurements of local and global extinction strain rates in counterflow diffusion flames have been reported at atmospheric pressure for six different compositions of syngas fuel. The concentration of H-2 was varied from 5 to 20% with a 3% increment, and correspondingly, CO was decreased from 35 to 20% in steps of 3%. Particle imaging velocimetry has been used to determine the local extinction strain rates. Local extinction strain rates increased with an increase in the H-2/CO ratio in both nonpremixed and premixed flames. The predicted extinction strain rates for both nonpremixed and premixed counterflow flames using five different mechanisms available in the literature were compared with measurements. The Davis H-2/CO and Ranzi H-2/CO mechanisms predicted extinction strain rates within 10% of experimental values irrespective of the H-2/CO ratio. In the nonpremixed case, the Cl mechanism by Li et al., GRI 3.0, and the Ranzi H-2/CO mechanism predicted extinction strain rates well for low H-2/CO ratios (from 5:35 to 14:26) but deviated from experiments for higher H-2/CO values (17:23 and 20:20). In addition to kinetics, preferential diffusion effects were found to affect the reaction zone significantly and create distinct localized reaction zone structures in nonpremixed flames, which could contribute to discrepancies in extinction predictions.

Analysis of Temperature and Pressure Changes in Liquefied Natural Gas (LNG) Cryogenic Tanks

Liquefied natural gas (LNG) is being developed as a transportation fuel for heavy vehicles such as trucks and transit buses, to lessen the dependency on oil and to reduce greenhouse gas emissions. The LNG stations are properly designed to prevent the venting of natural gas (NG) from LNG tanks, which can cause evaporative greenhouse gas emissions and result in fluctuations of fuel flow and changes of fuel composition. Boil-off is caused by the heat added into the LNG fuel during the storage and fueling. Heat can leak into the LNG fuel through the shell of tank during the storage and through hoses and dispensers during the fueling. Gas from tanks onboard vehicles, when returned to LNG tanks, can add additional heat into the LNG fuel. A thermodynamic and heat transfer model has been developed to analyze different mechanisms of heat leak into the LNG fuel. The evolving of properties and compositions of LNG fuel inside LNG tanks is simulated. The effect of a number of buses fueled each day on the possible total fuel loss rate has been analyzed. It is found that by increasing the number of buses, fueled each day, the total fuel loss rate can be reduced significantly. It is proposed that an electric generator be used to consume the boil-off gas or a liquefier be used to re-liquefy the boiloff gas to reduce the tank pressure and eliminate fuel losses. These approaches can prevent boil-off of natural gas emissions, and reduce the costs of LNG as transportation fuel.

Effects of mechanical and electrical coupling on the parametric sensitivity of mode localized sensors

We compare and contrast the effects of two distinctly different mechanisms of coupling (mechanical and electrical) on the parametric sensitivity of micromechanical sensors utilizing mode localization for sensor applications. For the first time, the strong correlation between mode localization and the phenomenon of 'eigenvalue loci-veering' is exploited for accurate quantification of the strength of internal coupling in mode localized sensors. The effects of capacitive coupling-spring tuning on the parametric sensitivity of electrically coupled resonators utilizing this sensing paradigm is also investigated and a mass sensor with sensitivity tunable by over 400% is realized. ©2009 IEEE.

Response of multiple simultaneously recorded macaque area LIP neurons in a memory saccade task

Cells in the lateral intraparietal cortex (LIP) of rhesus macaques respond vigorously and in spatially-tuned fashion to briefly memorized visual stimuli. Responses to stimulus presentation, memory maintenance, and task completion are seen, in varying combination from neuron to neuron. To help elucidate this functional segmentation a new system for simultaneous recording from multiple neighboring neurons was developed. The two parts of this dissertation discuss the technical achievements and scientific discoveries, respectively.

Technology. Simultanous recordings from multiple neighboring neurons were made with four-wire bundle electrodes, or tetrodes, which were adapted to the awake behaving primate preparation. Signals from these electrodes were partitionable into a background process with a 1/f-like spectrum and foreground spiking activity spanning 300-6000 Hz. Continuous voltage recordings were sorted into spike trains using a state-of-the-art clustering algorithm, producing a mean of 3 cells per site. The algorithm classified 96% of spikes correctly when tetrode recordings were confirmed with simultaneous intracellular signals. Recording locations were verified with a new technique that creates electrolytic lesions visible in magnetic resonance imaging, eliminating the need for histological processing. In anticipation of future multi-tetrode work, the chronic chamber microdrive, a device for long-term tetrode delivery, was developed.

Science. Simultaneously recorded neighboring LIP neurons were found to have similar preferred targets in the memory saccade paradigm, but dissimilar peristimulus time histograms, PSTH). A majority of neighboring cell pairs had a difference in preferred directions of under 45° while the trial time of maximal response showed a broader distribution, suggesting homogeneity of tuning with het erogeneity of function. A continuum of response characteristics was present, rather than a set of specific response types; however, a mapping experiment suggests this may be because a given cell's PSTH changes shape as well as amplitude through the response field. Spike train autocovariance was tuned over target and changed through trial epoch, suggesting different mechanisms during memory versus background periods. Mean frequency-domain spike-to-spike coherence was concentrated below 50 Hz with a significant maximum of 0.08; mean time-domain coherence had a narrow peak in the range ±10 ms with a significant maximum of 0.03. Time-domain coherence was found to be untuned for short lags (10 ms), but significantly tuned at larger lags (50 ms).

Carbon-carbon bond forming reactions from bis(carbene)-platinum(II) complexes and olefin polymerization and oligomerization using group 4 post-metallocene complexes

A long-standing challenge in transition metal catalysis is selective C–C bond coupling of simple feedstocks, such as carbon monoxide, ethylene or propylene, to yield value-added products. This work describes efforts toward selective C–C bond formation using early- and late-transition metals, which may have important implications for the production of fuels and plastics, as well as many other commodity chemicals.

The industrial Fischer-Tropsch (F-T) process converts synthesis gas (syngas, a mixture of CO + H₂) into a complex mixture of hydrocarbons and oxygenates. Well-defined homogeneous catalysts for F-T may provide greater product selectivity for fuel-range liquid hydrocarbons compared to traditional heterogeneous catalysts. The first part of this work involved the preparation of late-transition metal complexes for use in syngas conversion. We investigated C–C bond forming reactions via carbene coupling using bis(carbene)platinum(II) compounds, which are models for putative metal–carbene intermediates in F-T chemistry. It was found that C–C bond formation could be induced by either (1) chemical reduction of or (2) exogenous phosphine coordination to the platinum(II) starting complexes. These two mild methods afforded different products, constitutional isomers, suggesting that at least two different mechanisms are possible for C–C bond formation from carbene intermediates. These results are encouraging for the development of a multicomponent homogeneous catalysis system for the generation of higher hydrocarbons.

A second avenue of research focused on the design and synthesis of post-metallocene catalysts for olefin polymerization. The polymerization chemistry of a new class of group 4 complexes supported by asymmetric anilide(pyridine)phenolate (NNO) pincer ligands was explored. Unlike typical early transition metal polymerization catalysts, NNO-ligated catalysts produce nearly regiorandom polypropylene, with as many as 30-40 mol % of insertions being 2,1-inserted (versus 1,2-inserted), compared to <1 mol % in most metallocene systems. A survey of model Ti polymerization catalysts suggests that catalyst modification pathways that could affect regioselectivity, such as C–H activation of the anilide ring, cleavage of the amine R-group, or monomer insertion into metal–ligand bonds are unlikely. A parallel investigation of a Ti–amido(pyridine)phenolate polymerization catalyst, which features a five- rather than a six-membered Ti–N chelate ring, but maintained a dianionic NNO motif, revealed that simply maintaining this motif was not enough to produce regioirregular polypropylene; in fact, these experiments seem to indicate that only an intact anilide(pyridine)phenolate ligated-complex will lead to regioirregular polypropylene. As yet, the underlying causes for the unique regioselectivity of anilide(pyridine)phenolate polymerization catalysts remains unknown. Further exploration of NNO-ligated polymerization catalysts could lead to the controlled synthesis of new types of polymer architectures.

Finally, we investigated the reactivity of a known Ti–phenoxy(imine) (Ti-FI) catalyst that has been shown to be very active for ethylene homotrimerization in an effort to upgrade simple feedstocks to liquid hydrocarbon fuels through co-oligomerization of heavy and light olefins. We demonstrated that the Ti-FI catalyst can homo-oligomerize 1-hexene to C₁₂ and C₁₈ alkenes through olefin dimerization and trimerization, respectively. Future work will include kinetic studies to determine monomer selectivity by investigating the relative rates of insertion of light olefins (e.g., ethylene) vs. higher α-olefins, as well as a more detailed mechanistic study of olefin trimerization. Our ultimate goal is to exploit this catalyst in a multi-catalyst system for conversion of simple alkenes into hydrocarbon fuels.

Experimental chemical physics of droplets and clusters

Time-of-flight measurements of energetic He atoms, field ionization of cryogenic liquid helium clusters, and time-of-flight and REMPI spectroscopy of radical salt clusters were investigated experimentally. The excited He atoms were generated in a corona discharge. Two strong neutral peaks were observed, accompanied by a prompt photon peak and a charged peak. All peaks were correlated with the pulsing of the discharge. The neutral hyperthermal and metastable atoms were formed by different mechanisms at different stages of the corona discharge. Positively charged helium droplets were produced by ionization of liquid helium in an electrostatic spraying experiment. The fluid emerging from a thin glass capillary was ionized by a high voltage applied to a needle inside the capillary. Fine droplets (less than 10 µm in diameter) were produced in showers with currents as high as 0.4 µA at 2-4 kV. The high currents resulting from field ionization in helium and the low surface tension of He I, led to charge densities that greatly exceeded the Rayleigh limit, thus resulting in coulombic explosion of the liquid. In contrast, liquid nitrogen formed a well-defined Taylor cone with droplets having diameters comparable to the jet (≈100 µm) at lower currents (10 nA) and higher voltages (8 kV). The metal-halide clusters of calcium and chlorine were generated by laser ablation of calcium metal in a Ar/CCl₄ expansion. A visible spectrum of the Ca₂Cl₃ cluster was observed from 651 to 630 nm by 1 +1' REMPI. The spectra were composed of a strong origin band at 15 350.8 cm^-1 and several weak vibronic bands. Density functional calculations predicted three minimum energy isomers. The spectrum was assigned to the ²B₂ ← X ²A₁ transition of a planar C_2V structure having a ring of two Cl and two Ca atoms and a terminal Cl atom. The ring isomer of Ca₂Cl₃ has the unpaired electron localized on one Ca²⁺ ion to form a Ca⁺ chromophore. A second electronic band of Ca₂Cl₃ was observed at 720 nm. The band is sharply different from the 650 nm band and likely due to a different isomer.

Cosmological consequences of dark matter interactions and vacuum fluctuations

This thesis is divided into two parts: interacting dark matter and fluctuations in cosmology. There is an incongruence between the properties that dark matter is expected to possess between the early universe and the late universe. Weakly-interacting dark matter yields the observed dark matter relic density and is consistent with large-scale structure formation; however, there is strong astrophysical evidence in favor of the idea that dark matter has large self-interactions. The first part of this thesis presents two models in which the nature of dark matter fundamentally changes as the universe evolves. In the first model, the dark matter mass and couplings depend on the value of a chameleonic scalar field that changes as the universe expands. In the second model, dark matter is charged under a hidden SU(N) gauge group and eventually undergoes confinement. These models introduce very different mechanisms to explain the separation between the physics relevant for freezeout and for small-scale dynamics.

As the universe continues to evolve, it will asymptote to a de Sitter vacuum phase. Since there is a finite temperature associated with de Sitter space, the universe is typically treated as a thermal system, subject to rare thermal fluctuations, such as Boltzmann brains. The second part of this thesis begins by attempting to escape this unacceptable situation within the context of known physics: vacuum instability induced by the Higgs field. The vacuum decay rate competes with the production rate of Boltzmann brains, and the cosmological measures that have a sufficiently low occurrence of Boltzmann brains are given more credence. Upon further investigation, however, there are certain situations in which de Sitter space settles into a quiescent vacuum with no fluctuations. This reasoning not only provides an escape from the Boltzmann brain problem, but it also implies that vacuum states do not uptunnel to higher-energy vacua and that perturbations do not decohere during slow-roll inflation, suggesting that eternal inflation is much less common than often supposed. Instead, decoherence occurs during reheating, so this analysis does not alter the conventional understanding of the origin of density fluctuations from primordial inflation.

Desarrollo de software para la realización de ensayos dinámicos de mecanismos de cinemática paralela

[ES]El presente Trabajo de Fin de Grado tiene como objetivo contribuir al desarrollo de un proyecto de investigación mediante la programación y control del movimiento de mecanismos de cinemática paralela para la realización de ensayos dinámicos. Dicho proyecto está enmarcado dentro de una línea de investigación del grupo de investigación CompMech de la UPV-­‐EHU que gira en torno al desarrollo y estudio de este tipo de mecanismos. Esto es; este trabajo, más allá de la utilidad que pudiera tener por sí mismo, está pensado para formar parte de un proyecto de mayor envergadura, para cuyo éxito será imprescindible la colaboración con otros investigadores y la integración de este trabajo con los realizados por ellos. Consiste en la creación de un software para el control y movimiento de mecanismos, generando vibraciones para la realización de ensayos dinámicos. Para ello, se programarán sobre la plataforma LabVIEW la interfaz de usuario y el motor de cálculo. Una vez se compruebe que el programa funciona correctamente, se integrará dentro de un programa principal, un control articular que será el encargado de comunicarse con la máquina. Posteriormente, se procederá a la realización de ensayos experimentales sobre los propios robots, en taller. Se tomarán medidas mediante acelerómetros y otros dispositivos, determinando las medidas más adecuadas para su correcta validación. Finalmente, se generalizará el trabajo realizado para posibilitar su empleo futuro en diferentes mecanismos

Diseño cinemático de un mecanismo espacial de cinemática paralela

[ES]Este Trabajo Fin de Grado está enmarcado dentro de un proyecto del grupo de investigación CompMech. El proyecto consiste en el diseño y construcción de un mecanismo de cinemática paralela para ensayos dinámicos. Este trabajo fin de grado engloba las tareas necesarias para el estudio del espacio de trabajo del mecanismo y la determinación de las dimensiones más apropiadas desde consideraciones cinemáticas. Se partirá de tres posibles mecanismos, de los que más adelante se seleccionará uno con el que terminar el ciclo de diseño. Para ello el primer paso es el análisis cinemático de los mecanismos. Se resolverán los problemas de posición y de velocidades, que serán los necesarios para el posterior estudio del espacio de trabajo. La resolución de estos problemas se programará en un programa Matlab. Después se obtendrán los espacios de trabajo de cada uno de los mecanismos, así como las posiciones singulares dentro del mismo, y su variación ante variaciones en las dimensiones. Será también de interés determinar las regiones del espacio de trabajo en las que más fácil es efectuar el movimiento del mecanismo. Conocidos los espacios de trabajo de cada mecanismo y su variabilidad con cambios en las dimensiones, se elegirá el mecanismo más apropiado para continuar con el ciclo de diseño. Para la elección se tendrán también en cuenta consideraciones adicionales aportadas por otros miembros del grupo.

Estudio, análisis y clasificación de mecanismos con aplicación industrial

[ES]El uso de maquinaria en la industria es algo muy habitual en la actualidad. Dicha maquinaria necesita una serie de mecanismos para realizar una acción deseada, y en función de esa acción, se hará uso de un mecanismo u otro. Este informe representa el estudio y análisis cinemático que se ha llevado a cabo para la posterior clasificación de mecanismos planos que tengan un grado de libertad con aplicación industrial. Para todo ello se ha partido de un previo conocimiento de la materia que se ha ido complementando con diferentes fuentes de información especializadas. La clasificación de los mecanismos que se va a realizar en este trabajo no es más que una de las muchas posibilidades que hay a la hora de clasificarlos ya que se han hecho bastantes intentos para realizar clasificaciones de mecanismos, pero dada la complejidad de la tarea no se ha llegado a una clasificación general unificada. La línea de trabajo que se presenta aquí consiste en el análisis cinemático de diferentes mecanismos para la posterior creación de un prototipo de uno de ellos. La estructura de los contenidos que se desarrollan a continuación es la siguiente: En primer lugar se ha realizado una búsqueda de mecanismos que cumplan la condición de ser mecanismos planos que tengan un grado de libertad y que tengan utilidad demostrada. En segundo lugar se han recopilado los resultados cinemáticos del mecanismo, construcciones gráficas de los elementos que lo componen y se añadirán animaciones de cada mecanismo, haciendo después una valoración en función de los resultados obtenidos de los mismos. En tercer lugar se han clasificado en diferentes grupos dependiendo de su función o aplicación. En cuarto lugar, se ha realizado un prototipo de uno de los mecanismos para comprobar su funcionamiento.

The impact of physical processes on algal growth

Mixing and transport processes in surface waters strongly influence the structure of aquatic ecosystems. The impact of mixing on algal growth is species-dependent, affecting the competition among species and acting as a selective factor for the composition of the biocoenose. Were it not for the ever-changing ”aquatic weather”, the composition of pelagic ecosystems would be relatively simple. Probably just a few optimally adapted algal species would survive in a given water-body. In contrast to terrestrial ecosystems, in which the spatial heterogeneity is primarily responsible for the abundance of niches, in aquatic systems (especially in the pelagic zone) the niches are provided by the temporal structure of physical processes. The latter are discussed in terms of the relative sizes of physical versus biological time-scales. The relevant time-scales of mixing and transport cover the range between seconds and years. Correspondingly, their influence on growth of algae is based on different mechanisms: rapid changes are relevant for the fast biological processes such as nutrient uptake and photosynthesis, and the slower changes are relevant for the less dynamic processes such as growth, respiration, mineralization, and settling of algal cells. Mixing time-scales are combined with a dynamic model of photosynthesis to demonstrate their influence on algal growth.

Citocinas proinflamatorias: participación en la modulación de la actividad del melanoma experimental B16

252 p. : il.

Efeito da ingestão crônica de vinho sobre a homeostase glicêmica, lipídica e ponderal em camundongos ApoE Knockout

Os benefícios à saúde relacionados ao consumo moderado de vinho incluem diferentes mecanismos, nos quais estão envolvidos tanto etanol quanto compostos fenólicos que são constituintes do mesmo. Com o objetivo de avaliar variações glicêmicas, ponderais e o depósito de triglicérides, colesterol e glicogênio hepáticos com uso regular de vinho tinto em camundongo ApoE Knockout, foram utilizados 60 camundongos machos adultos ApoE Knockout de peso médio de 30 gramas, distribuídos em três grupos de 20 animais: grupo vinho, grupo etanol e grupo água, os quais receberam 50 mL de vinho e 50 mL água, 6mL de etanol e 94mL de água e somente água respectivamente por quatro meses. Os parâmetros avaliados foram: variações glicêmicas, ponderais, acúmulo de triglicerídeos, colesterol e glicogênio hepáticos. O grupo vinho teve em relação a sua massa corporal uma área sob a curva maior que a dos outros dois grupos, mas com um percentual pequeno de aumento. A concentração do triglicerídeo hepático foi maior no grupo vinho 57% em relação ao grupo etanol, que foi 31,6% menor que o controle (p<0,01%). A concentração do colesterol hepático foi menor no grupo vinho (23,6%), assim como no grupo etanol (24,5%), (p<0,05%). A concentração do glicogênio hepático foi maior no grupo vinho (16%), porém não alcançando significado estatístico. A glicemia em jejum no dia da eutanásia foi maior no grupo etanol em relação aos demais grupos, porém não demonstrou diferença estatisticamente significante. Na análise histológica não foi observada diferença significativa entre os grupos, embora o peso médio em gramas nas gorduras, retroperitoneal e subcutâneas tenha sido aproximadamente duas vezes maior no grupo vinho. Concluiu-se que neste estudo o uso regular e crônico de vinho tinto aumentou triglicerídeo hepático, porém o álcool diminui o colesterol hepático. O aumento do triglicerídeo pode ser devido ao alto valor calórico do vinho ou alguma propriedade lipogênica desconhecida que levou ao aumento importante das gorduras retroperitoneais e subcutâneas em camundongos ApoE Knockout.