BETs: Propellant less de orbiting of space debris by bare electrodynamic tethers

As a fundamental contribution to limiting the increase of debris in the Space environment, a three-year project started on 1 November 2010 financed by the European Commission under the FP-7 Space Programme. It aims at developing a universal system to be carried on board future satellites launched into low Earth orbit (LEO), to allow de-orbiting at end of life. The operational system involves a conductive tape-tether left bare of insulation to establish anodic contact with the ambient plasma as a giant Langmuir probe. The project will size the three disparate dimensions of a tape for a selected de-orbit mission and determine scaling laws to allow system design for a general mission. It will implement control laws to restrain tether dynamics in/off the orbital plane; and will carry out plasma chamber measurements and numerical simulations of tether-plasma interaction. The project also involves the design and manufacturing of subsystems: electron-ejecting plasma contactors, an electric control and power module, interface elements, tether and deployment mechanisms, tether tape/end-mass as well as current collection plus free-fall, and hypervelocity impact tests.

Diseño para fabricación digital: definición unívoca entre forma y fabricación en arquitectura

La presente investigación se inicia planteando el objetivo de identificar los parámetros geométricos que son exclusivos del proceso de generación de la Forma y relacionarlos con los invariantes relacionados con la Fabricación digital aplicada a la Arquitectura. Con ello se pretende recuperar la geometría como herramienta principal del proceso de Proyecto ampliando su ámbito de actuación al encontrar una relación con los procesos de fabricación digital. El primer capítulo describe los antecedentes y contexto histórico centrándose especialmente en la influencia de la capacidad de definir geometrías complejas digitalmente mediante la aplicación de algoritmos. En los primeros ejemplos la aproximación del Arquitecto a proyectos con geometrías complejas no euclídeas aún se emplea sin precisión en la comunicación de la geometría ideada para su puesta en obra. Las técnicas constructivas obligan a asumir una tolerancia de desviación entre proyecto y obra y la previsión del comportamiento de esa geometría no permite asegurar su comportamiento final. No será hasta la introducción de herramientas CAD en el proceso de ideación arquitectónica cuando el Arquitecto se capacite para generar geometrías no representables de forma analógica. Sin embargo, la imposibilidad de trasladar la geometría proyectada a la praxis constructiva impedirá la plasmación de un proceso completo, salvo en las contadas ocasiones que se recogen en este texto. “El análisis cronológico de las referencias establece como aspecto esencial para la construcción de geometrías complejas la capacidad primero para definir y comunicar de forma precisa e inequívoca la geometría y después la capacidad de analizar el desempeño prestacional de dicha propuesta geométrica”. La presente investigación se inicia planteando el objetivo de identificar los parámetros geométricos que son exclusivos del proceso de generación de la Forma y relacionarlos con los invariantes relacionados con la Fabricación digital aplicada a la Arquitectura. Con ello se pretende recuperar la geometría como herramienta principal del proceso de Proyecto ampliando su ámbito de actuación al encontrar una relación con los procesos de fabricación digital. El primer capítulo describe los antecedentes y contexto histórico centrándose especialmente en la influencia de la capacidad de definir geometrías complejas digitalmente mediante la aplicación de algoritmos. En los primeros ejemplos la aproximación del Arquitecto a proyectos con geometrías complejas no euclídeas aún se emplea sin precisión en la comunicación de la geometría ideada para su puesta en obra. Las técnicas constructivas obligan a asumir una tolerancia de desviación entre proyecto y obra y la previsión del comportamiento de esa geometría no permite asegurar su comportamiento final. No será hasta la introducción de herramientas CAD en el proceso de ideación arquitectónica cuando el Arquitecto se capacite para generar geometrías no representables de forma analógica. Sin embargo, la imposibilidad de trasladar la geometría proyectada a la praxis constructiva impedirá la plasmación de un proceso completo, salvo en las contadas ocasiones que se recogen en este texto. “El análisis cronológico de las referencias establece como aspecto esencial para la construcción de geometrías complejas la capacidad primero para definir y comunicar de forma precisa e inequívoca la geometría y después la capacidad de analizar el desempeño prestacional de dicha propuesta geométrica”. Establecida la primera conclusión, el capítulo de contexto histórico continúa enfocándose sobre la aplicación de las técnicas digitales en el Proceso de proyecto primero, y en la puesta en obra después. Los casos de estudio identifican claramente como un punto de inflexión para la generación de formas complejas mediante un software CAD el Museo Guggenheim de Bilbao en 1992. El motivo esencial para elegir este proyecto como el primer proyecto digital es el uso de la herramienta de definición digital de la geometría para su reproducción inequívoca en obra. “La revolución digital ha aportado al Arquitecto la posibilidad de abandonar las tipologías arquitectónicas basados en restricciones geométricas-constructivas. La aplicación de técnicas de fabricación digital ha permitido la capacidad de diseñar con independencia del sistema constructivo y libertad formal. En este nuevo contexto las prestaciones suponen los nuevos límites conceptuales, ya que el acceso y disposición de la información del comportamiento de las alternativas que cada geometría conlleva demanda del Arquitecto la jerarquización de los objetivos y la formulación en un conjunto coherente de parámetros”. Los proyectos que emplean herramientas digitales para la resolución de las distintas etapas del proceso proyectual se verán incrementados de forma exponencial desde 1992 hasta nuestros días. A pesar del importante auge de las técnicas de diseño asistido por ordenador el principal desafío sigue siendo la vinculación de las geometrías y materiales propuestos con las capacidades de las técnicas de manufactura y puesta en obra. El proceso de diseño para fabricación en un entorno digital es una tecnología madura en otras industrias como la aeroespacial o la automovilística, incluso la de productos de consumo y decoración, sin embargo en el sector de Construcción es un sistema inmaduro e inconexo. Las particularidades de la industria de la construcción aún no han sido abordadas en su totalidad y las propuestas de investigación realizadas en este ámbito se han centrado hasta 2015 en partes del proceso y no en el proceso total. “El principal obstáculo para la estandarización e implantación globalizada de un proceso digital desde el origen de la forma hasta la construcción es la inexistencia de un protocolo integrado que integre las limitaciones de fabricación, económicas y de puesta en obra junto a la evaluación de desempeño prestacional durante la fases iniciales de proyecto”. En el capítulo número 3 se estudian los distintos procesos de generación de la forma. Se propone una definición específica para el ámbito de la investigación de “forma” en el entendemos que se incluye la envolvente exterior y el conjunto organizativo de espacios interiores conectados. Por lo tanto no es excluyente del interior. El objetivo de este estudio es analizar y clasificar los procesos para la generación digital de formas en los distintos proyectos seleccionados como emblemáticos de cada tipología. Se concluye que la aproximación a este proceso es muy variada y compleja, con aplicación segregada y descoordinada entre los distintos agentes que han intervenir. En un proceso de generación formal analógico los parámetros que intervienen son en parte conscientes y en parte inconscientes o aprendidos. El Arquitecto sólo tiene control sobre la parte consciente de los parámetros a integrar en el diseño, de acuerdo a sus conocimientos y capacidades será capaz de manejar un número limitado de parámetros. La parte aprendida permanece en el inconsciente y dirige el proceso analógico, aportando prejuicios estéticos incorporados durante el proceso formativo y propio del entorno cultural. “El empleo de herramientas digitales basadas en la evaluación prestacional durante el proceso de selección formal permite al Arquitecto conocer “en tiempo real” el desempeño en el conjunto de prestaciones evaluadoras del conjunto de alternativas geométricas a la propuesta previamente definida por la intuición arquitectónica. El proceso definido no persigue identificar una solución óptima sino asistir al Arquitecto en el proceso de generación de la forma mediante la evaluación continua de los vectores direccionales más idóneos que el procedimiento generativo plantea”. La definición de complejidad en generación y producción de formas en relación con el proceso de diseño digital paramétrico global o integrado, es esencial para establecer un protocolo que optimice su gestión. “Se propone como definición de complejidad como factor resultante de multiplicar el número de agentes intervinientes por el número de parámetros e interacciones comunes que intervienen en el proceso de generación de la forma, dividido por la complejidad de intercambio de información digital desde el origen hasta la fase de fabricación y construcción”. Una vez analizados los procesos de generación digital de Arquitectura se propone identificar los parámetros geométricos que definen el proceso de Diseño digital, entendiendose por Diseño el proceso que engloba desde la proposición de una forma inicial basada en la intuición del Arquitecto, la generación y evaluación de variantes y posterior definición digital para producción, tanto de un objeto, un sistema o de la totalidad del Proyecto. En la actualidad el proceso de Diseño es discontinuo y lineal organizandose los parámetros por disciplinas en las que está estructurada las atribuciones profesionales en la industria de la construcción. Para simplificar la identificación y listado se han agrupado siguiendo estos grupos de conocimiento. Entendemos parametros invariables aquellos que son independientes de Tipologías arquitectónicas o que dependen del mismo proceso de generación de la Forma. “El listado de los parámetros que intervienen en un proceso de generación formal es una abstracción de una realidad compleja. La parametrización de las decisiones que intervienen en la selección de una forma determinada mediante “well defined problems” es imposible. El proceso que esta tesis describe entiende esta condición como un elemento que pone en valor el propio procedimiento generativo por la riqueza que la subjetividad que el equipo de diseño aporta”. La segunda parte esencial de esta investigación pretende extraer las restricciones propias del estado del arte de la fabricación digital para posteriormente incorporarlos en los procesos digitales de definición de la Forma arquitectónica. “La integración de las restricciones derivadas de las técnicas de fabricación y construcción digitales en el proceso de generación de formas desde el ámbito de la Arquitectura debe referirse a los condicionantes geométricos asociados a cada sistema constructivo, material y técnica de fabricación. La geometría es además el vínculo que permite asociar el conjunto de parámetros prestacionales seleccionados para un Proyecto con los sistemas de fabricación digital”. A estos condicionantes geométricos obtenidos del análisis de cada sistema de fabricación digital se les ha denominado “invariantes geométricos”. Bajo este término se engloban tanto límites dimensionales de fabricación, como materiales compatibles, tolerancias de manufactura e instalación y cualidades prestacionales asociadas. El objetivo de esta propuesta es emplear la geometría, herramienta fundamental y propia del Arquitecto, como nexo de unión entre el conjunto complejo y heterogéneo de parámetros previamente listados y analizados. Para ello se han simplificado en tablas específicas para cada parámetro prestacional los condicionantes geométricos que se derivan de los Sistemas de fabricación digital compatibles (ver apéndice 1). El estudio y evaluación de las capacidades y objetivos de las distintas plataformas de software disponibles y de las experiencias profesionales evaluadas en los proyectos presentados, permiten concluir que la propuesta de plataforma digital de diseño integral multi-paramétrico de formas arquitectónicas requiere de un protocolo de interoperatibilidad específico aún no universalmente establecido. Actualmente el enfoque de la estrategia para normalizar y universalizar el contexto normativo para regular la interoperatibilidad se centra en figura del gestor denominado “BIM manager”. Las atribuciones y roles de esta figura se enfocan a la gestión del continente y no del contenido (Definición de los formatos de intercambio, niveles de desarrollo (LOD) de los componentes o conjuntos constructivos, detección de interferencias y documentación del propio modelo). Siendo este ámbito un desarrollo necesario para la propuesta de universalización del sistema de diseño para fabricación digital integrado, la presente investigación aporta un organigrama y protocolo asociado. El protocolo: 1. Establece la responsabilidad de identificar y definir la Información que debe determinar el proceso de generación y desarrollo de la forma arquitectónica. 2. Define la forma digital apropiada para generar la geometría del Proyecto, incluyendo la precisión necesaria para cada componente y el nivel de detalle necesario para su exportación inequívoca al proceso de fabricación. 3. Define el tempo de cada etapa de diseño identificando un nivel de detalle acorde. 4. Acopla este organigrama dentro de las estructuras nuevas que se proponen en un entorno BIM para asegurar que no se producen solapes o vacíos con las atribuciones que se identifican para el BIM Manager. “El Arquitecto debe dirigir el protocolo de generación coordinada con los sistemas de producción digital para conseguir que la integración completa. El protocolo debe asistir al proceso de generación de forma mediante la evaluación del desempeño prestacional de cada variante en tiempo real. La comunicación entre herramientas digitales es esencial para permitir una ágil transmisión de información. Es necesario establecer un protocolo adaptado a los objetivos y las necesidades operativas de cada proyecto ya que la estandarización de un protocolo único no es posible”. Una decisión estratégica a la hora de planificar una plataforma de diseño digital común es establecer si vamos a optar por un Modelo digital único o diversos Modelos digitales federados. Cada uno de los modos de trabajo tiene fortalezas y debilidades, no obstante en el ámbito de investigación se ha concluido que un proceso integrado de Diseño que incorpore la evaluación prestacional y conceptual definida en el Capítulo 3, requiere necesariamente de varios modelos de software distintos que han de relacionarse entre sí mediante un protocolo de comunicación automatizado. Una plataforma basada en un modelo federado consiste en establecer un protocolo de comunicación entre los programas informáticos empleados por cada disciplina. En este modelo de operación cada equipo de diseño debe establecer las bases de comunicación en función del número y tipo de programas y procesos digitales a emplear. En esta investigación se propone un protocolo basado en los estándares de intercambio de información que estructura cualquier proceso de generación de forma paramétrico “La investigación establece el empleo de algoritmos evolutivos como el sistema actual óptimo para desarrollar un proceso de generación de formas basadas en la integración y coordinación de invariantes geométricos derivados de un conjunto de objetivos prestacionales y constructivos. No obstante, para la aplicación en el caso práctico realizado se ha podido verificar que la evaluación del desempeño aún no puede realizarse en una única herramienta y por lo tanto el proceso de selección de las variantes genéticas óptimas ha de ejecutarse de forma manual y acumulativa. El proceso debe realizarse de manera federada para la selección evolutiva de los invariantes geométricos dimensionales”. La evaluación del protocolo de integración y los condicionantes geométricos obtenidos como parámetros geométricos que controlan las posibles formas compatibles se realiza mediante su aplicación en un caso práctico. El ejercicio simula la colaboración multidisciplinar con modelos federados de plataformas distintas. La elección del tamaño y complejidad constructiva del proyecto se ha modulado para poder alcanzar un desarrollo completo de cada uno de los parámetros prestacionales seleccionados. Continuando con el mismo objetivo propuesto para los parámetros prestacionales, la tipología constructiva-estructural seleccionada para el ejercicio permite la aplicación la totalidad de invariantes geométricos asociados. El objetivo de este caso práctico es evaluar la capacidad alterar la forma inicialmente propuesta mediante la evaluación del desempeño prestacional de conjunto de variantes geométricas generadas a partir de un parámetro dimensional determinado. Para que este proceso tenga sentido, cada una de las variantes debe ser previamente validada conforme a las limitaciones geométricas propias de cada sistema de fabricación y montaje previstos. El interés de las conclusiones obtenidas es la identificación de una variante geométrica distante a la solución simétrica inicialmente como la solución óptima para el conjunto de parámetros seleccionados. Al tiempo se ha comprobado como la participación de un conjunto de parámetros multi-disciplinares que representan la realidad compleja de los objetivos arquitectónicos favorecen la aparición de variaciones genéticas con prestaciones mejoradas a la intuición inicial. “La herencias tipológicas suponen un límite para la imaginación de variantes formales al proceso de ideación arquitectónica. El ejercicio realizado demuestra que incluso en casos donde aparentemente la solución óptima aparenta ser obvia una variante aleatoria puede mejorar su desempeño global. La posibilidad de conocer las condiciones geométricas de las técnicas de fabricación digital compatibles con el conjunto de parámetros seleccionados por el Arquitecto para dirigir el proceso asegura que los resultados del algoritmo evolutivo empleado sean constructivamente viables. La mejora de imaginación humana con la aportación de geometrías realmente construibles supone el objetivo último de esta tesis”. ABSTRACT Architectural form generation process is shifting from analogical to digital. Digital technology has changed the way we design empowering Architects and Engineers to precisely define any complex geometry envisioned. At the same time, the construction industry, following aeronautical and automotive industries, is implementing digital manufacturing techniques to improve efficiency and quality. Consequently construction complexity will no longer be related to geometry complexity and it is associated to coordination with digital manufacturing capacities. Unfortunately it is agreed that non-standard geometries, even when proposed with performance optimization criteria, are only suitable for projects with non-restricted budgets. Furthemore, the lack of coordinated exportation protocol and geometry management between design and construction is avoiding the globalization of emergence process in built projects Present research first objective is to identify exclusive form-generation parameters related to digital manufacturing geometrical restraints. The intention was to use geometry as the form-generation tool and integrate the digital manufacturing capacities at first stages of the project. The first chapter of this text describes the investigation historical context focusing on the influence between accurate geometry definition at non-standard forms and its construction. At first examples of non-Euclidean geometries built the communication between design and construction were based on analogical partial and imprecise documentation. Deficient communication leads to geometry adaptation on site leaving the final form uncontrolled by the Architect. Computer Aided Design enable Architects to define univocally complex geometries that previously where impossible to communicate. “The univocally definition of the Form, and communication between design and construction is essential for complex geometry Projects”. The second chapter is focused on digital technologies application in form finding process and site construction. The case studies selected identifies a clear inflexion node at 1992 with the Guggenheim Museum in Bilbao. The singularity of this project was the use of Aeronautics software to define digitally the external envelope complex geometry to enable the contractor to build it. “The digital revolution has given the Architect the capacity to design buildings beyond the architectural archetypes driven by geometric-constructive limitations. The application of digital manufacturing techniques has enabled a free-form construction without geometrical limitations. In this new context performance shall be the responsible to set new conceptual boundaries, since the behavior of each possible geometry can be compare and analyze beforehand. The role of the Architect is to prioritize the performance and architectural objectives of each project in a complete and coherent set of parameters”. Projects using digital tools for solving various stages of the design process were increased exponentially since 1992 until today. Despite the significant rise of the techniques of computer-aided design the main challenge remains linking geometries and materials proposed at each design with the capabilities of digital manufacturing techniques. Design for manufacturing in a digital environment is a mature technology in other industries such as aerospace and automotive, including consumer products and decoration, but in the construction sector is an immature and disjointed system. The peculiarities of the construction industry have not yet been addressed in its entirety and research proposals made in this area until 2015 have focused in separate parts of the process and not the total process. “The main obstacle to global standardization and implementation of a complete digital process from the form-finding to construction site is the lack of an integrated protocol that integrates manufacturing, economic and commissioning limitations, together with the performance evaluation of each possible form”. The different form generation processes are studied at chapter number 3. At the introduction of this chapter there is a specific definition of "form" for the research field. Form is identified with the outer envelope geometry, including the organizational set of connected indoor spaces connected to it. Therefore it is not exclusive of the interior. The aim of this study is to analyze and classify the main digital form generation processes using different selected projects as emblematic of each type. The approach to this process is complex, with segregated and uncoordinated different actors have to intervene application. In an analogical form-generation process parameters involved are partly conscious and partly unconscious or learned. The architect has control only over limited part of the parameters to be integrated into the design, according to their knowledge and. There is also a learned aesthetical prejudice that leads the form generation process to a specific geometry leaving the performance and optimization criteria apart from the decision making process. “Using performance evaluation digital tools during form finding process provides real-time comparative information to the Architect enabling geometry selection based on its performance. The generative form generation process described at this document does not ambition to identify the optimum geometry for each set of parameters. The objective is to provide quick information at each generation of what direction is most favorable for the performance parameters selected”. Manufacturing complexity definition in relation to a global and integral process of digital design for manufacture is essential for establishing an efficient managing protocol. “The definition of complexity associated to design for production in Architecture is proposed as the factor between number of different agents involved in the process by the number of interactions required between them, divided by the percentage of the interchange of information that is standardized and proof of information loss”. Design in architecture is a multi-objective process by definition. Therefore, addressing generation process linked to a set of non-coherent parameters requires the selection of adequate generative algorithm and the interaction of the architect. During the second half of the twentieth century and early twenty-first century it have been developed various mathematical algorithms for multi-parametric digital design. Heuristic algorithms are the most adequate algorithms for architectural projects due to its nature. The advantage of such algorithms is the ability to efficiently handle large scale optimization cases where a large number of design objectives and variables are involved. These generative processes do not pursue the optimum solution, in fact it will be impossible to proof with such algorithm. This is not a problem in architectural design where the final goal is to guide the form finding process towards a better performance within the initial direction provided by the architect. This research has focused on genetic algorithms due to its capacity to generate geometric alternatives in multiple directions and evaluate the fitness against a set of parameters specified in a single process. "Any protocol seeks to achieve standardization. The design to manufacturing protocol aims to provide a coordinated and coherent form generation process between a set of design parameters and the geometrical requirements of manufacturing technique. The protocol also provides an information exchange environment where there is a communication path and the level of information is ensured. The research is focused on the process because it is considered that each project will have its own singularities and parameters but the process will stay the same. Again the development of a specific tool is not a goal for the research, the intention is to provide an open source protocol that is valid for any set of tools”. Once the digital generation processes are being analized and classified, the next step is to identify the geometric parameters that define the digital design process. The definition of design process is including from the initial shape proposal based on the intuition of the architect to the generation, evaluation, selection and production of alternatives, both of an object , system or of the entire project . The current design process in Architecture is discontinuous and linear, dividing the process in disciplines in which the construction industry is structured. The proposal is to unify all relevant parameters in one process. The parameters are listed in groups of knowledge for internal classification but the matrix used for parameter relationship determination are combined. “A multi-parameter determination of the form-finding process is the integration all the measurable decisions laying behind Architect intuition. It is not possible to formulate and solve with an algorithm the design in Architecture. It is not the intention to do so with the proposal of this research. The process aims to integrate in one open protocol a selection of parameters by using geometry as common language. There is no optimum solution for any step of the process, the outcome is an evaluation of performance of all the form variations to assist the Architect for the selection of the preferable solution for the project”. The research follows with the geometrical restrictions of today Digital manufacturing techniques. Once determined it has been integrated in the form-finding process. “Digital manufacturing techniques are integrated in the form-finding process using geometry as common language. Geometric restraints define the boundary for performance parametric form-finding process. Geometrical limitations are classified by material and constructive system”. Choose between one digital model or several federate models is a strategic decision at planning a digital design for manufacturing protocol. Each one of the working models have strengths and weakens, nevertheless for the research purposes federated models are required to manage the different performance evaluation software platforms. A protocol based on federated models shall establish a communication process between software platforms and consultants. The manager shall integrate each discipline requirements defining the communication basis. The proposed protocol is based on standards on information exchange with singularities of the digital manufacturing industry. “The research concludes evolutionary algorithms as current best system to develop a generative form finding process based on the integration and coordination of a set of performance and constructive objectives. However, for application in professional practice and standardize it, the performance evaluation cannot be done in only one tool and therefore the selection of optimal genetic variants must be run in several iterations with a cumulative result. Consequently, the evaluation process within the geometrical restraints shall be carried out with federated models coordinated following the information exchange protocol”. The integration protocol and geometric constraints evaluation is done by applying in a practical case study. The exercise simulates multidisciplinary collaboration across software platforms with federated models. The choice of size and construction complexity of the project has been modulated to achieve the full development of each of the parameters selected. Continuing with the same objective proposed for the performance parameters the constructive and structural type selected for the exercise allows the application all geometric invariants associated to the set of parameters selected. The main goal of the case study is to proof the capacity of the manufacturing integrated form finding process to generate geometric alternatives to initial form with performance improved and following the restrictions determined by the compatible digital manufacturing technologies. The process is to be divided in consecutive analysis each one limited by the geometrical conditions and integrated in a overall evaluation. The interest of this process is the result of a non-intuitive form that performs better than a double symmetrical form. The second conclusion is that one parameter evaluation alone will not justify the exploration of complex geometry variations, but when there is a set of parameters with multidisciplinary approach then the less obvious solution emerge as the better performing form. “Architectural typologies impose limitation for Architects capacity to imagine formal variations. The case study and the research conclusions proof that even in situations where the intuitive solution apparently is the optimum solution, random variations can perform better when integrating all parameters evaluation. The capacity of foreseing the geometrical properties linking each design parameter with compatible manufacturing technologies ensure the result of the form-finding process to be constructively viable. Finally, the propose of a complete process where the geometry alternatives are generated beyond the Architect intuition and performance evaluated by a set of parameters previously selected and coordinated with the manufacturing requirements is the final objective of the Thesis”.

A new boundary-based morphological model

Mathematical morphology addresses the problem of describing shapes in an n-dimensional space using the concepts of set theory. A series of standardized morphological operations are defined, and they are applied to the shapes to transform them using another shape called the structuring element. In an industrial environment, the process of manufacturing a piece is based on the manipulation of a primitive object via contact with a tool that transforms the object progressively to obtain the desired design. The analogy with the morphological operation of erosion is obvious. Nevertheless, few references about the relation between the morphological operations and the process of design and manufacturing can be found. The non-deterministic nature of classic mathematical morphology makes it very difficult to adapt their basic operations to the dynamics of concepts such as the ordered trajectory. A new geometric model is presented, inspired by the classic morphological paradigm, which can define objects and apply morphological operations that transform these objects. The model specializes in classic morphological operations, providing them with the determinism inherent in dynamic processes that require an order of application, as is the case for designing and manufacturing objects in professional computer-aided design and manufacturing (CAD/CAM) environments. The operators are boundary-based so that only the points in the frontier are handled. As a consequence, the process is more efficient and more suitable for use in CAD/CAM systems.

Development of a Mechanism and Process to Continuously Produce Spherical, Torrefied Biomass

Thesis (Master, Mechanical and Materials Engineering) -- Queen's University, 2016-06-17 02:15:25.215

Challenges to the Patent System in face of Open Hardware

Dannie Jost gave a presentation outlining some of the challenges to the patent system presented by open source hardware at the "Open Knowledge Festival", under the topic stream treating open design, hardware, manufacturing and making; September 19, 2012; Helsinki, Finland. This topic stream generated considerable discussion, and it serves to educate an audience that is usually very adverse to patents and copyright, and helps the researcher understand the issuing conflicts surrounding emerging technologies, in particular digital technologies, and the maker movement (digitally enabled).

Computer integrated system for form-roll manufacture

Computer integrated manufacture has brought about great advances in manufacturing technology and its recognition is world wide. Cold roll forming of thin-walled sections, and in particular the design and manufacture of form-rolls, the special tooling used in the cold roll forming process, is but one such area where computer integrated manufacture can make a positive contribution. The work reported in this thesis, concerned with the development of an integrated manufacturing system for assisting the design and manufacture of form-rolls, was undertaken in collaboration with a leading manufacturer of thin-walled sections. A suit of computer programs, written in FORTRAN 77, have been developed to provide computer aids for every aspect of work in form-roll design and manufacture including cost estimation and stock control aids. The first phase of the development programme dealt with the establishment of CAD facilities for form-roll design, comprising the design of the finished section, the flower pattern, the roll design and the interactive roll editor program. Concerning the CAM facilities, dealt with in the second phase, an expert system roll machining processor and a general post-processor have been developed for considering the roll geometry and automatically generating NC tape programs for any required CNC lathe system. These programs have been successfully implemented, as an integrated manufacturing software system, on the VAX 11/750 super-minicomputer with graphics facilities for displaying drawings interactively on the terminal screen. The development of the integrated system has been found beneficial in all aspects of form-roll design and manufacture. Design and manufacturing lead times have been reduced by several weeks, quality has improved considerably and productivity has increased. The work has also demonstrated the promising nature of the expert systems approach to computer integrated manufacture.

Using process-oriented holonic (PrOH) modelling to increase understanding of information systems

Methodologies for understanding business processes and their information systems (IS) are often criticized, either for being too imprecise and philosophical (a criticism often levied at softer methodologies) or too hierarchical and mechanistic (levied at harder methodologies). The process-oriented holonic modelling methodology combines aspects of softer and harder approaches to aid modellers in designing business processes and associated IS. The methodology uses holistic thinking and a construct known as the holon to build process descriptions into a set of models known as a holarchy. This paper describes the methodology through an action research case study based in a large design and manufacturing organization. The scientific contribution is a methodology for analysing business processes in environments that are characterized by high complexity, low volume and high variety where there are minimal repeated learning opportunities, such as large IS development projects. The practical deliverables from the project gave IS and business process improvements for the case study company.

Introduction : the role of quality, production and technological innovation in improving competitive performance

Quality, production and technological innovation management rank among the most important matters of concern to modern manufacturing organisations. They can provide companies with the decisive means of gaining a competitive advantage, especially within industries where there is an increasing similarity in product design and manufacturing processes. The papers in this special issue of International Journal of Technology Management have all been selected as examples of how aspects of quality, production and technological innovation can help to improve competitive performance. Most are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the theme was 'Getting Ahead Through Technology and People'. At the conference itself over 80 papers were presented by authors from 15 countries around the world. Among the many topics addressed within the conference theme, technological innovation, quality and production management emerged as attracting the greatest concern and interest of delegates, particularly those from industry. For any new initiative to be implemented successfully, it should be led from the top of the organization. Achieving the desired level of commitment from top management can, however, be a difficulty. In the first paper of this issue, Mackness investigates this question by explaining how systems thinking can help. In the systems approach, properties such as 'emergence', 'hierarchy', 'commnication' and 'control' are used to assist top managers in preparing for change. Mackness's paper is then complemented by Iijima and Hasegawa's contribution in which they investigate the development of Quality Information Management (QIM) in Japan. They present the idea of a Design Review and demonstrate how it can be used to trace and reduce quality-related losses. The next paper on the subject of quality is by Whittle and colleagues. It relates to total quality and the process of culture change within organisations. Using the findings of investigations carried out in a number of case study companies, they describe four generic models which have been identified as characterising methods of implementing total quality within existing organisation cultures. Boaden and Dale's paper also relates to the management of quality, but looks specifically at the construction industry where it has been found there is still some confusion over the role of Quality Assurance (QA) and Total Quality Management (TQM). They describe the results of a questionnaire survey of forty companies in the industry and compare them to similar work carried out in other industries. Szakonyi's contribution then completes this group of papers which all relate specifically to the question of quality. His concern is with the two ways in which R&D or engineering managers can work on improving quality. The first is by improving it in the laboratory, while the second is by working with other functions to improve quality in the company. The next group of papers in this issue all address aspects of production management. Umeda's paper proposes a new manufacturing-oriented simulation package for production management which provides important information for both design and operation of manufacturing systems. A simulation for production strategy in a Computer Integrated Manufacturing (CIM) environment is also discussed. This paper is then followed by a contribution by Tanaka and colleagues in which they consider loading schedules for manufacturing orders in a Material Requirements Planning (MRP) environment. They compare mathematical programming with a knowledge-based approach, and comment on their relative effectiveness for different practical situations. Engstrom and Medbo's paper then looks at a particular aspect of production system design, namely the question of devising group working arrangements for assembly with new product structures. Using the case of a Swedish vehicle assembly plant where long cycle assembly work has been adopted, they advocate the use of a generally applicable product structure which can be adapted to suit individual local conditions. In the last paper of this particular group, Tay considers how automation has affected the production efficiency in Singapore. Using data from ten major industries he identifies several factors which are positively correlated with efficiency, with capital intensity being of greatest interest to policy makers. The two following papers examine the case of electronic data interchange (EDI) as a means of improving the efficiency and quality of trading relationships. Banerjee and Banerjee consider a particular approach to material provisioning for production systems using orderless inventory replenishment. Using the example of a single supplier and multiple buyers they develop an analytical model which is applicable for the exchange of information between trading partners using EDI. They conclude that EDI-based inventory control can be attractive from economic as well as other standpoints and that the approach is consistent with and can be instrumental in moving towards just-in-time (JIT) inventory management. Slacker's complementary viewpoint on EDI is from the perspective of the quality relation-ship between the customer and supplier. Based on the experience of Lucas, a supplier within the automotive industry, he concludes that both banks and trading companies must take responsibility for the development of payment mechanisms which satisfy the requirements of quality trading. The three final papers of this issue relate to technological innovation and are all country based. Berman and Khalil report on a survey of US technological effectiveness in the global economy. The importance of education is supported in their conclusions, although it remains unclear to what extent the US government can play a wider role in promoting technological innovation and new industries. The role of technology in national development is taken up by Martinsons and Valdemars who examine the case of the former Soviet Union. The failure to successfully infuse technology into Soviet enterprises is seen as a factor in that country's demise, and it is anticipated that the newly liberalised economies will be able to encourage greater technological creativity. This point is then taken up in Perminov's concluding paper which looks in detail at Russia. Here a similar analysis is made of the concluding paper which looks in detail at Russia. Here a similar analysis is made of the Soviet Union's technological decline, but a development strategy is also presented within the context of the change from a centralised to a free market economy. The papers included in this special issue of the International Journal of Technology Management each represent a unique and particular contribution to their own specific area of concern. Together, however, they also argue or demonstrate the general improvements in competitive performance that can be achieved through the application of modern principles and practice to the management of quality, production and technological innovation.

Proceedings of the 6th CIRP-Sponsored International Conference on Digital Enterprise Technology

This Proceedings volume contains articles presented at the CIRP-Sponsored International Conference on Digital Enterprise Technology (DET2009) that takes place 14-16 December 2009 in Hong Kong. This is the 6th DET conference in the series and the first to be held in Asia. Professor Paul Maropoulos initiated, hosted and chaired the 1st International DET Conference held in 2002 at the University of Durham. Since this inaugural first DET conference, DET conference series has been successfully held in 2004 at Seattle, Washington USA, in 2006 at Setubal Portugal, in 2007 at Bath England, and in 2008 at Nantes France. The DET2009 conference continues to bring together International expertise from the academic and industrial fields, pushing forward the boundaries of research knowledge and best practice in digital enterprise technology for design and manufacturing, and logistics and supply chain management. Over 120 papers from over 10 countries have been accepted for presentation at DET2009 and inclusion in this Proceedings volume after stringent refereeing process.

Guest editorial:special issue on digitial enterprise technology

Full text This Proceedings volume contains selected papers from the Fourth International CIRP-sponsored, Conference on Digital Enterprise Technology (DET2007), which was held at the University of Bath, UK, 19–21 September 2007. All selected papers have been suitably enhanced for publication in the Journal and have undergone full review. Digital enterprise technology (DET) is ‘the collection of systems and methods for the digital modelling and analysis of the global product development and realization process, in the context of lifecycle management.’ The principal aim of the DET concept is to provide a coherent context for the development and integration of the various digital technologies that underpin modern design and manufacturing. These technologies can be classified according to the following five key areas. 1. Distributed and collaborative design. 2. Process modelling and process planning. 3. Advanced factory design and modelling. 4. Physical-to-digital environment integrators–verification. 5. Enterprise integration technologies. This special issue is representative of the wide breadth of the DET concept including; a comprehensive review of digital engineering, design processes, digital modelling of machine tools, forming, robotics and machining processes, verification and metrology, and dynamic networks. It is particularly pleasing to see the development of metrology as a key aspect of modern manufacturing technology, linking design intent to process capability. The papers published herein will facilitate the exploration of new and evolving research concepts by the international research community and will influence the development of international standards for the application of DET technologies.

Methodology to create cost estimation models for engineer-to-order operations

This research addresses the problem of cost estimation for product development in engineer-to-order (ETO) operations. An ETO operation starts the product development process with a product specification and ends with delivery of a rather complicated, highly customized product. ETO operations are practiced in various industries such as engineering tooling, factory plants, industrial boilers, pressure vessels, shipbuilding, bridges and buildings. ETO views each product as a delivery item in an industrial project and needs to make an accurate estimation of its development cost at the bidding and/or planning stage before any design or manufacturing activity starts. ^ Many ETO practitioners rely on an ad hoc approach to cost estimation, with use of past projects as reference, adapting them to the new requirements. This process is often carried out on a case-by-case basis and in a non-procedural fashion, thus limiting its applicability to other industry domains and transferability to other estimators. In addition to being time consuming, this approach usually does not lead to an accurate cost estimate, which varies from 30% to 50%. ^ This research proposes a generic cost modeling methodology for application in ETO operations across various industry domains. Using the proposed methodology, a cost estimator will be able to develop a cost estimation model for use in a chosen ETO industry in a more expeditious, systematic and accurate manner. ^ The development of the proposed methodology was carried out by following the meta-methodology as outlined by Thomann. Deploying the methodology, cost estimation models were created in two industry domains (building construction and the steel milling equipment manufacturing). The models are then applied to real cases; the cost estimates are significantly more accurate than the actual estimates, with mean absolute error rate of 17.3%. ^ This research fills an important need of quick and accurate cost estimation across various ETO industries. It differs from existing approaches to the problem in that a methodology is developed for use to quickly customize a cost estimation model for a chosen application domain. In addition to more accurate estimation, the major contributions are in its transferability to other users and applicability to different ETO operations. ^

DEVELOPMENT OF A MECHANISM AND PROCESS TO CONTINUOUSLY PRODUCE SPHERICAL, TORREFIED BIOMASS PELLETS

A recently developed novel biomass fuel pellet, the Q’ Pellet, offers significant improvements over conventional white pellets, with characteristics comparable to those of coal. The Q’ Pellet was initially created at bench scale using a proprietary die and punch design, in which the biomass was torrefied in-situ¬ and then compressed. To bring the benefits of the Q’ Pellet to a commercial level, it must be capable of being produced in a continuous process at a competitive cost. A prototype machine was previously constructed in a first effort to assess continuous processing of the Q’ Pellet. The prototype torrefied biomass in a separate, ex-situ reactor and transported it into a rotary compression stage. Upon evaluation, parts of the prototype were found to be unsuccessful and required a redesign of the material transport method as well as the compression mechanism. A process was developed in which material was torrefied ex-situ and extruded in a pre-compression stage. The extruded biomass overcame multiple handling issues that had been experienced with un-densified biomass, facilitating efficient material transport. Biomass was extruded directly into a novel re-designed pelletizing die, which incorporated a removable cap, ejection pin and a die spring to accommodate a repeatable continuous process. Although after several uses the die required manual intervention due to minor design and manufacturing quality limitations, the system clearly demonstrated the capability of producing the Q’ Pellet in a continuous process. Q’ Pellets produced by the pre-compression method and pelletized in the re-designed die had an average dry basis gross calorific value of 22.04 MJ/kg, pellet durability index of 99.86% and dried to 6.2% of its initial mass following 24 hours submerged in water. This compares well with literature results of 21.29 MJ/kg, 100% pellet durability index and <5% mass increase in a water submersion test. These results indicate that the methods developed herein are capable of producing Q’ Pellets in a continuous process with fuel properties competitive with coal.

Intelligent DMU creation: Nominal CAD model preparation for automated tolerance allocation

This paper examines the integration of a tolerance design process within the Computer-Aided Design (CAD) environment having identified the potential to create an intelligent Digital Mock-Up [1]. The tolerancing process is complex in nature and as such reliance on Computer-Aided Tolerancing (CAT) software and domain experts can create a disconnect between the design and manufacturing disciplines It is necessary to implement the tolerance design procedure at the earliest opportunity to integrate both disciplines and to reduce workload in tolerance analysis and allocation at critical stages in product development when production is imminent.
The work seeks to develop a methodology that will allow for a preliminary tolerance allocation procedure within CAD. An approach to tolerance allocation based on sensitivity analysis is implemented on a simple assembly to review its contribution to an intelligent DMU. The procedure is developed using Python scripting for CATIA V5, with analysis results aligning with those in literature. A review of its implementation and requirements is presented.

The role of Lean at the interface with between operations management and applied services within a large aerospace organisation: a boundary spanning perspective

Increased complexity in large design and manufacturing organisations requires improvements at the operations management (OM)–applied service (AS) interface areas to improve project effectiveness. The aim of this paper is explore the role of Lean in improving the longitudinal efficiency of the OM–AS interface within a large aerospace organisation using Lean principles and boundary spanning theory. The methodology was an exploratory longitudinal case approach including exploratory interviews (n = 21), focus groups (n = 2), facilitated action-research workshops (n = 2) and two trials or experiments using longitudinal data involving both OM and AS personnel working at the interface. The findings draw upon Lean principles and boundary spanning theory to guide and interpret the findings. It was found that misinterpretation, and forced implementation, of OM-based Lean terminology and practice in the OM–AS interface space led to delays and misplaced resources. Rather both OM and AS staff were challenged to develop a cross boundary understanding of Lean-based boundary (knowledge) objects in interpreting OM requests. The longitudinal findings from the experiments showed that the development of Lean Performance measurements and lean Value Stream constructs was more successful when these Lean constructs were treated as boundary (knowledge) objects requiring transformation over time to orchestrate improved effectiveness and in leading to consistent terminology and understanding between the OM–AS boundary spanning team.

Appraisal of open software for finite element simulation of 2D metal sheet laser cut.

FEA simulation of thermal metal cutting is central to interactive design and manufacturing. It is therefore relevant to assess the applicability of FEA open software to simulate 2D heat transfer in metal sheet laser cuts. Application of open source code (e.g. FreeFem++, FEniCS, MOOSE) makes possible additional scenarios (e.g. parallel, CUDA, etc.), with lower costs. However, a precise assessment is required on the scenarios in which open software can be a sound alternative to a commercial one. This article contributes in this regard, by presenting a comparison of the aforementioned freeware FEM software for the simulation of heat transfer in thin (i.e. 2D) sheets, subject to a gliding laser point source. We use the commercial ABAQUS software as the reference to compare such open software. A convective linear thin sheet heat transfer model, with and without material removal is used. This article does not intend a full design of computer experiments. Our partial assessment shows that the thin sheet approximation turns to be adequate in terms of the relative error for linear alumina sheets. Under mesh resolutions better than 10e−5 m , the open and reference software temperature differ in at most 1 % of the temperature prediction. Ongoing work includes adaptive re-meshing, nonlinearities, sheet stress analysis and Mach (also called ‘relativistic’) effects.