Prediction of bendig load capacity of timber beams by finite element method simulation of knots and grain deviation

A finite element model was used to simulate timberbeams with defects and predict their maximum load in bending. Taking into account the elastoplastic constitutive law of timber, the prediction of fracture load gives information about the mechanisms of timber failure, particularly with regard to the influence of knots, and their local graindeviation, on the fracture. A finite element model was constructed using the ANSYS element Plane42 in a plane stress 2D-analysis, which equates thickness to the width of the section to create a mesh which is as uniform as possible. Three sub-models reproduced the bending test according to UNE EN 408: i) timber with holes caused by knots; ii) timber with adherent knots which have structural continuity with the rest of the beam material; iii) timber with knots but with only partial contact between knot and beam which was artificially simulated by means of contact springs between the two materials. The model was validated using ten 45 × 145 × 3000 mm beams of Pinus sylvestris L. which presented knots and graindeviation. The fracture stress data obtained was compared with the results of numerical simulations, resulting in an adjustment error less of than 9.7%

Qualitative behaviour of L1 and L2 standard deviation in insulations measurements according to standard UNE EN ISO 140-4

Knowledge of the uncertainty of measurement of testing results is important when results have to be compared with limits and specifications. In the measurement of sound insulation following standards UNE EN ISO 140-4 the uncertainty of the final magnitude is mainly associated to the average sound pressure levels L1 and L2 measured. A parameter that allows us to quantify the spatial variation of the sound pressure level is the standard deviation of the pressure levels measured at different points of the room. In this work, for a wide number of measurements following standards UNE EN ISO 140-4 we analyzed qualitatively the behaviour of the standard deviation for L1 and L2. The study of sound fields in enclosed spaces is very difficult. There are a wide variety of rooms with different sound fields depending on factors as volume, geometry and materials. In general, we observe that the L1 and L2 standard deviations contain peaks and dips independent on characteristics of the rooms at single frequencies that could correspond to critical frequencies of walls, floors and windows or even to temporal alterations of the sound field. Also, in most measurements according to UNE EN ISO 140-4 a large similitude between L1 and L2 standard deviation is found. We believe that such result points to a coupled system between source and receiving rooms, mainly at low frequencies the shape of the L1 and L2 standard deviations is comparable to the velocity level standard deviation on a wall

Reply to Comment on ``Towards a large deviation theory for strongly correlated systems''

The computational study commented by Touchette opens the door to a desirable generalization of standard large deviation theory for special, though ubiquitous, correlations. We focus on three interrelated aspects: (i) numerical results strongly suggest that the standard exponential probability law is asymptotically replaced by a power-law dominant term; (ii) a subdominant term appears to reinforce the thermodynamically extensive entropic nature of q-generalized rate function; (iii) the correlations we discussed, correspond to Q -Gaussian distributions, differing from Lévy?s, except in the case of Cauchy?Lorentz distributions. Touchette has agreeably discussed point (i), but, unfortunately, points (ii) and (iii) escaped to his analysis. Claiming the absence of connection with q-exponentials is unjustified.

Aircraft flight trajectory deviation in the standard instrument departures. Operators penalties.

In the recent years many problems are emerging due to the aircraft noise on the airport surrounding areas. The solution to this problem is not easy considering that the neighbourhood asks for the reduction of the number of aircraft operations and the airlines ask for a growing demand in the number of operations in the major airports. So the airport and regulatory authorities try to get a solution imposing a fine to the aircraft which its actual trajectory differs from the nominal one more than a lateral deviation. But, which is the value of this deviation?. The current situation is that many operators have to pay a lot of money for exceeding a deviation which has been established without operational criteria. This paper presents the results of a research program which is being carried out by the authors which aims to determine the "delta" deviation to be used for this purpose. In addition it is proposed a customized method per SID and per airport to be used for determining the maximum allowed lateral deviation by which if the aircraft is within it, then none fine will be imposed.

Deviation of Cup and Propeller Anemometer Calibration Results with Air Density

The effect of air density variations on the calibration constants of several models of anemometers has been analyzed. The analysis was based on a series of calibrations between March 2003 and February 2011. Results indicate a linear behavior of both calibration constants with the air density. The effect of changes in air density on the measured wind speed by an anemometer was also studied. The results suggest that there can be an important deviation of the measured wind speed with changes in air density from the one at which the anemometer was calibrated, and therefore the need to take this effect into account when calculating wind power estimations.

DEVCON: Stata module to apply the deviation contrast transform to estimation results

devcon transforms the coefficients of 0/1 dummy variables so that they reflect deviations from the "grand mean" rather than deviations from the reference category (the transformed coefficients are equivalent to those obtained by the so called "effects coding") and adds the coefficient for the reference category. The variance-covariance matrix of the estimates is transformed accordingly. The transformed estimated can be used with post estimation procedures. In particular, devcon can be used to solve the identification problem for dummy variable effects in the so-called Blinder-Oaxaca decomposition (see the oaxaca package).

Social deviation,

"Suggestions for supplementary readings" at end of each chapter.

Tables describing small-sample properties of the mean, median, standard deviation, and other statistics in sampling from various distributions /

Mode of access: Internet.

Definitions in political economy, preceded by an inquiry into the rules which ought to guide political economists in the definition and use of their terms, with remarks on the deviation from these rules in their writings.

Mode of access: Internet.

Genetic and environmental influences on dentofacial structures and oral health: studies of Australian twins and their families

Our studies of the teeth and faces of Australian twins commenced at the School of Dentistry, The University of Adelaide in the early 1980s. There are now over 900 pairs of twins enrolled in our continuing investigations, together with 1200 relatives. There are 3 main cohorts of participants. The first cohort comprises around 300 pairs of teenage twins for whom various records have been collected, including dental casts, facial photographs, finger and palm prints and information on laterality, including handedness. The second cohort comprises around 300 pairs of twins who have been examined at 3 stages of dental development from approximately 4 years of age to about 14 years: at primary, mixed, and permanent dentition (excluding 3rd molars) stages. The most recent study of tooth emergence and oral health, for which we are currently recruiting twins, will provide a third cohort of around 500 twin pairs aged from around birth to 3 to 4 years of age. Our broad aim in these studies has been to improve our understanding of how genetic and environmental factors contribute to variation in dental and facial features, and to oral health. We have also used our data to investigate aspects of the determination of laterality, particularly the fascinating phenomenon of mirror imaging. We plan to maximize the use of the longitudinal data and DNA we have collected, and continue to collect, by performing genome-wide scans for putative genetic linkage peaks for a range of dental features, and then to test for association between a series of likely candidate genes and our phenotypes.