Comportamento dinâmico-mecânico e relaxações em polímeros e blendas poliméricas

Dynamic mechanical analysis (DMA) is widely used in materials characterization. In this work, we briefly introduce the main concepts related to this technique such as, linear and non-linear viscoelasticity, relaxation time, response of material when it is submitted to a sinusoidal or other periodic stress. Moreover, the main applications of this technique in polymers and polymer blends are also presented. The discussion includes: phase behavior, crystallization; spectrum of relaxation as a function of frequency or temperature; correlation between the material damping and its acoustic and mechanical properties.

Avaliação das propriedades de compósitos de polipropileno reforçados com casca de aveia

The preparation of oat-reinforced polypropylene nanocomposites with different fiber contents by means of melt-processing was investigated. Composite properties were evaluated by Scanning Electron Microscopy (SEM), Flexural Modulus, Dynamic Mechanical Analysis (DMA), Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA). Findings confirmed that the oat composite properties were affected by fiber type and content. Improvements in mechanical properties were obtained using fiber contents < 20% w.t.

Uso de diferentes herbicidas no controle de Myriophyllum aquaticum

Este estudo teve a finalidade de avaliar, em condições de caixa d'água, o controle químico de Myriophyllum aquaticum (pinheiro-d'água), através de herbicidas aplicados em pós-emergência. Os herbicidas e respectivas doses (g ha-1) foram: diquat (Reward) a 204 g i.a. ha-1; diquat a 102 e 204 g i.a. ha-1 + Agral a 0,1%; 2,4-D (DMA 806 BR) a 167, 335, 670 e 1.340 g e.a. ha-1; glyphosate (Rodeo) a 3.360 g e.a. ha-1 + Aterbane a 0,5%; e imazapyr (Arsenal) a 250 g e.a. ha-1. As parcelas foram constituídas por caixas d'água de 0,60 x 0,60 x 0,45 m, com 120 litros de água + 20 litros de solo e 20 ramos por caixa. Utilizou-se um pulverizador costal a pressão constante de CO2 a 2 bar, pontas 110.02 VS, com um consumo de calda de 180 l ha-1. O controle foi avaliado visualmente aos 2, 6, 9,11, 13, 17, 20, 23, 26, 30 e 36 dias após a aplicação dos herbicidas (DAAH). Inicialmente, o herbicida diquat foi o composto que apresentou os sintomas mais severos de intoxicação nos ramos de pinheiro-d'água aos 2 DAAH, com 65% de controle em média, e aos 20 DAAH ele atingiu o controle máximo (99%), porém ocorreram rebrotas a partir dos 23 DAAH, independentemente da adição ou não de Agral e das doses testadas. O herbicida 2,4-D proporcionou 100% de controle dos ramos a partir dos 23 DAAH para as doses de 1.340 e 670 g ha-1, não ocorrendo rebrotas; já para as demais doses testadas (335 e 167 g ha-1) o controle não foi eficiente, pois ocorreram rebrotas. Os herbicidas glyphosate e imazapyr não foram eficientes no controle desta espécie.

Segurança das condições de aplicação de herbicidas com aerobarco em plantas daninhas aquáticas no lago da Hidrelétrica de Jupiá

Os objetivos deste trabalho foram quantificar as exposições dérmicas (EDs) e respiratórias (ERs) proporcionadas ao piloto e ao seu ajudante nas aplicações de herbicidas para o controle de plantas daninhas aquáticas com aerobarco; classificar essas condições de trabalho em seguras ou inseguras; e calcular a necessidade de controle das exposições (NCE) e o tempo de trabalho seguro (TTS). O aerobarco utilizado tinha casco de alumínio (4,85 x 2,42 m) e acionamento por hélice acoplada a motor a gasolina de 350 HP. O equipamento de pulverização era composto por bomba de diafragma com fluxo máximo de 49,69 L min-1, pressão máxima de 25 kg cm-2, acionada por motor a gasolina de 4 HP, e tanque de calda de 189 L. A barra de pulverização de alumínio era composta de duas seções laterais de 3 m, posicionadas na linha entre o encosto do banco do piloto e o início da estrutura protetora da hélice. Cada seção da barra tinha seis bicos com pontas de jato plano com indução de ar AI 100 03, espaçados de 0,5 m, e uma ponta OC 20 fixada em cada extremidade. O conjunto de pontas pulverizava faixas de 6 m de largura e aplicava o volume de calda de 200 L ha-1. O sistema tinha gerenciador de fluxo, controlado por central eletrônica acoplada a DGPS (com precisão submétrica), para corrigir automaticamente a vazão em função de alterações na velocidade real da embarcação. As EDs e ERs aos herbicidas foram calculadas com os dados substitutos das exposições às caldas, avaliadas com os traçadores cobre e manganês adicionados às caldas. As exposições foram extrapoladas para uma jornada de trabalho de seis horas. A segurança das condições de trabalho foi determinada com o cálculo da margem de segurança (MS), utilizando-se a fórmula MS = (NOEL x 70)/(QAE x 10), em que QAE = quantidade absorvível da exposição. As condições de trabalho foram classificadas em seguras, se MS>1, ou inseguras, se MS<1. As exposições proporcionadas pelas condições de trabalho foram de 10,65 mL de calda por dia para o piloto e de 16,80 mL por dia para o ajudante, que fica sentado em uma cadeira a 2,0 m à frente do piloto e da barra de pulverização. Classificaram-se como seguras as aplicações dos herbicidas glyphosate (Rodeo, 6 L ha-1), 2,4D (DMA 806 BR, 8 L ha-1) e fluridone (Sonar AQ, 0,4 L ha-1), para o piloto e o seu ajudante. Classificou-se como insegura a aplicação do herbicida diquat (Reward, 4,0 L ha-1) para as duas condições de trabalho, cujas necessidades de controle das exposições calculadas foram de 65% para o piloto e de 78% para o ajudante do piloto.

Alterações anatômicas do limbo foliar de plantas de Polygonum lapathifolium submetidas à aplicação de herbicidas

O presente trabalho teve por objetivo avaliar a eficiência do controle dos herbicidas 2,4-D, diquat e glyphosate e as alterações anatômicas do limbo foliar provocadas por eles em plantas de Polygonum lapathifolium. As plantas foram cultivadas em caixas-d'água sob condições de campo e, quando atingiram seu pleno desenvolvimento (antes do florescimento), pulverizadas com os herbicidas. Avaliaram-se quantitativamente as seguintes características anatômicas da nervura central e internervural das folhas: porcentagem da epiderme adaxial e abaxial, porcentagem da bainha do feixe, porcentagem do feixe vascular, porcentagem de esclerênquima e colênquima, porcentagem de parênquima paliçádico e lacunoso, bem como a espessura foliar (μm). Os tratamentos químicos foram: diquat (400 g i.a. ha-1 do produto comercial Reward), 2,4-D (1.340 g e.a. ha -1 do produto comercial DMA 806 BR) e glyphosate (4.320 g e.a. ha-1 do produto comercial Rodeo) com a adição do surfatante Silwet L-77 a 0,01% v v-1. Os principais caracteres anatômicos quantitativos da região da nervura central do limbo foliar que sofreram alterações após a aplicação dos herbicidas foram a porcentagem da epiderme adaxial, a porcentagem de feixe vascular, a porcentagem de colênquima, a porcentagem de parênquima paliçádico e lacunoso e a espessura foliar. Para a região internervural do limbo foliar, os principais caracteres anatômicos quantitativos que sofreram alterações após a aplicação dos herbicidas foram a porcentagem da epiderme adaxial, a porcentagem da bainha do feixe e a espessura foliar. Os herbicidas diquat e 2,4-D foram ineficientes no controle das plantas de P. lapathifolium; o glyphosate apresentou controle superior a 90% das plantas aos 100 dias após a aplicação. Entretanto, todos os herbicidas permitiram rebrota das plantas.

Influência da chuva na eficácia do herbicida 2,4-D no controle de Myriophyllum aquaticum

O objetivo deste estudo foi avaliar a eficiência de controle de duas doses do herbicida 2,4-D pulverizado em plantas de M. aquaticum e submetido à simulação de chuva em diferentes períodos de tempo após sua aplicação. O delineamento experimental utilizado foi o inteiramente casualizado, com quatro repetições, disposto em um esquema fatorial 2 x 8 (duas doses de herbicida e oito intervalos de chuva). Utilizou-se o herbicida 2,4-D, na formulação comercial DMA 806, em duas doses: 670 e 1.340 g e.a. ha-1. A simulação de uma chuva de 15 mm, com duração de cinco minutos, foi realizada em oito intervalos de tempo após a pulverização do herbicida (0,25h, 0,5h, 1h, 2h, 4h, 8h, 12h e sem chuva). Foram realizadas avaliações visuais de controle aos 7, 14, 21 e 28 dias após a aplicação dos tratamentos. As duas doses avaliadas do herbicida 2,4-D foram eficientes no controle das plantas de M. aquaticum, mesmo com ocorrência de chuva 15 minutos após sua aplicação.

Efeito da chuva na eficiência de herbicidas aplicados em pós-emergência sobre corda-de-viola

O objetivo deste trabalho foi avaliar a influência da chuva na eficiência de herbicidas aplicados em pós-emergência em plantas de Ipomoea grandifolia. As plantas de I. grandifolia foram cultivadas em vasos plásticos com capacidade de 2,5 L, em casa de vegetação, com uma planta por vaso. O delineamento experimental utilizado foi o inteiramente casualizado, com quatro repetições, com os tratamentos dispostos em um esquema fatorial 7x8 (sete tratamentos químicos e oito períodos para ocorrência de chuva após a aplicação dos tratamentos). Os tratamentos químicos constaram da aplicação de glyphosate em cinco formulações comerciais (Roundup Original, Roundup WG, Roundup Transorb, Roundup Transorb R e Roundup Ultra) a 1.080 g e.a. ha-1, amônio-glufosinate (Finale) a 400 g i.a. ha-1 e 2,4-D (DMA 806) a 1.000 g e.a. ha-1 e de oito intervalos de tempo para simulação de uma chuva de 15 mm, com duração de cinco minutos: 15', 30', 1h, 2h, 4h, 6h, 8h após a aplicação dos tratamentos e uma testemunha sem chuva, Foram realizadas avaliações visuais de controle das plantas aos 7, 14, 21, 28 e 35 dias após a aplicação e, por ocasião da última avaliação, determinou-se a massa seca das plantas. A ocorrência de chuvas após a aplicação de 2,4-D não alterou a sua eficiência no controle das plantas de I. grandifolia; já os herbicidas amônio-glufosinate e glyphosate, em todas suas formulações testadas, apresentaram redução na eficiência de controle quando da ocorrência de chuvas em até oito horas após a aplicação dos tratamentos.

Decomposition of trimethylamine oxide related to the use of sulfites in shrimp

Currently, sulfites are employed on board to inhibit melanosis (blackspot) on crustaceans. However, when used in excess this chemical compound not only can cause adverse reactions in SO2-sensitive individuals, but also favors the decomposition of trimethylamine oxide (TMAO) into dimethylamine (DMA) and formaldehyde (FA), thus compromising the quality of the product, which can be observed mainly through the texture change of the meat after cooking. This study was conducted to verify the increase of the contents of DMA and FA by the excessive use of sodium metabisulfite in white shrimp (Penaeus schmitti). For laboratory trials, shrimp were beheaded, washed and immersed in a 2% sodium metabisulfite solution for 10 minutes. Specimens were stored either on ice and maintained for 48 hours in refrigeration, or stored in a freezer for 48 hours. Samples were collected at intervals of 0, 24 and 48 hours, and analyzed for residual SO2, TMAO, TMA, DMA and FA. The immersion of shrimp in a 2% sodium metabisulfite for 10 minutes favored the decomposition of TMAO which greatly increased the contents of DMA and FA. The FA and DMA measured in fresh shrimp was low. Moreover, the storage of shrimp tails on ice resulted in a significant reduction of the TMA, DMA, FA and residual SO2 contents compared to the specimens under frozen storage.

Modification of Polypropylene/Glass Fiber Composites with Nanosilica

Poly(propylene) (PP) reinforced with short glass fiber was modified with precipitated nanosilica (pnS) by melt mixing. The weight of the glass fiber was varied by keeping the pnS at optimum level. The properties of the composites were studied using universal testing machine, dynamic mechanic analyser (DMA), differential Scanning calorimetry (DSC) and thermo gravimetric analyser (TGA). The amount of the glass fiber required for a particular modulus could be reduced by the addition of nanosilica.

EPDM/CIIR Blends: Compatibility, Morphology and Physical Properties

A detailed study of the blends of ethylene-propylene-diene rubber (EPDM) and chlorobutyl rubber (CIIR) is proposed in this study. These blends may find application in the manufacture of curing diaphragms/curing envelopes for tire curing applications. EPDM possesses better physical properties such as high heat resistance, ozone resistance, cold and moisture resistance, high resistance to permanent defonnation, very good resistance to flex cracking and impact. Because of the low gas and moisture penneability, good weathering resistance and high thermal stability of CIIR, blends of EPDM with CIlR may be attractive, if sufficient mechanical strength can be developed. Although a lot of work has been done on elastomer blends, studies on the blends of EPDM and CIIR rubbers are meagre. Hence in this investigation it is proposed to make a systematic study on the characteristics of EPDM and CIIR rubber blends.The mechanical and physical properties of an elastomer blend depend mainly on the blend compatibility. So in the first part of the study, it is proposed to develop compatible blends of EPDM with CIIR. Various commercial grades of ethylenepropylene- diene rubber are proposed to be blended with a specific grade of chlorobutyl rubber at varying proportions. The extent of compatibility in these blends is proposed to be evaluated based on their mechanical properties such as tensile strength, tear strength and ageing resistance. In addition to the physical property measurements, blend compatibility is also proposed to be studied based on the glass transition behavlour of the blends in relation to the Tg's of the individual components using Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA). The phase morphology of the blends is also proposed to be investigated by Scanning Electron Microscopy (SEM) studies of the tensile fracture surfaces. In the case of incompatible blends, the effect of addition of chlorosulfonated polyethylene as a compatibiliser is also proposed to be investigated.In the second part of the study, the effect of sulphur curing and resin curing on the curing behaviour and the vulcanizate properties of EPDM/CIIR blends are planned to be evaluated. Since the properties of rubber vulcanizates are determined by their network structures, it is proposed to determine the network structure of the vulcanizates by chemical probes so as to correlate it with the mechanical properties.In the third part of the work, the effect of partial precuring of one of the components prior to blending as a possible means of improving the properties of the blend is proposed to be investigated. This procedure may also help to bring down the viscosity mismatch between the constituent e1astomers and provide covulcanization of the blend.The rheological characteristics and processability of the blends are proposed to be investigated in the last part of the study. To explore their possible applications, the air permeability of the blend samples at varying temperatures is proposed to be measured. The thermal diffusivity behaviour of EPDM/CIlR blends is also proposed to be investigated using novel laser technique. The thermal diffusivity of the blends along with the thermal degradation resistance may help to determine whether the blends are suitable for high temperature applications such as in the manufacturing of curing envelope.

Modification of Polypropylene and Polystyrene Using Nanosilica

The present work focuses on the modification of the commonly used thermoplastics, polypropylene and polystyrene using nanosilica preparcd from a cheap source of sodium silicate. Melt compounding technique has been used for nanocomposite preparation as it is simple and suited to injection moulding. Nanosilica in a polymer matrix provide significant enhancement in strength, stiffness and impact strength. Incorporation of silica particles in a polymer also improves its thennal stability. To achieve better dispersion of fillers in polymer matrices the mixing was done at different shear rates. The enhancement in material properties indicates that at higher shear rates there is greater interaction between particles and the matrix and it depends on filler concentration and type of polymer used. N anosilica is a useful filler in thennoplastic polymers and has been applied in automotive applications, electronic appliances and consumer goods.This thesis is divided into six chapters. General introduction to the topic is described in chapter 1. Salient features of polymer nanocomposites, their synthesis, properties and applications are presented. A review of relevant literature and the scope and objectives are also mentioned in this chapter.The materials used and the vanous experimental method and techniques employed in the study are described in chapter 2. Preparation of nanocomposites by melt blending using Thenno Haake Rheocord, preparation of samples, evaluation of mechanical and thennal properties using UTM, Impact testing and characterization using DMA, TGA and DSC and morphology by SEM are described.The preparation of nanosilica from a laboratory scale to a pilot plant scale is described in chapter 3. Generation of surface modified silica, evaluation of kinetic parameters of the synthesis reaction, scale up of the reactor and modeling of the reactor are also dealt with in this chapter.The modification of the commodity thennoplastic, Polypropylene using nanosilica is described in chapter 4. Preparation of PP/silica nanocomposites, evaluation of mechanical properties, thermal and crystallization characteristics, water absorption and ageing resistance studies are also presented.The modification of Polystyrene using synthesized nanosilica IS described in chapter 5. The method of preparation of PS/silica nanocomposites, evaluation of mechanical properties (static and dynamic), thermal properties melt flow characteristics using Haake Rheocord, water absorption and ageing resistance of these nanocomposites are studied.

Short Nylon-6 Fibre/Rubber-Toughened Polystyrene Composites

The thesis describes studies on development of short Nylon-6 fibre composites based on rubber-toughened polystyrene (PS). Toughening was done using natural rubber (NR), styrene-butadiene rubber (SBR) and whole tyre reclaim (WTR). The composites were prepared by melt mixing in an internal mixer at 170 oC. It was found that the optimum blend ratio was 85/15 for PS/NR, 90/10 for PS/SBR and 90/22 for PS/WTR blends. The effect of dynamic vulcanisation on 85/15 PS/NR and 90/10 PS/SBR blends using dicumyl peroxide (DCP) at various concentrations were also studied. The dynamic crosslinking improved the tensile properties, flexural properties, impact strength and dynamic mechanical properties of both the blends. The effect of unmodified and resorcinol formaldehyde latex (RFL)-coated short Nylon-6 fibres on the mechanical properties, morphology and dynamic mechanical properties of 85/15 PS/NR, 90/10 PS/SBR and 90/22 PS/WTR blends were studied. Fibre loading was varied from 0 to 3 wt.%. For 85/15 PS/NR blend, there was a significant enhancement in tensile properties, flexural properties and impact strength with 1 wt.% of both unmodified and RFL-coated fibres. Dynamic mechanical analysis revealed that the storage modulus at room temperature was maximum at 1 wt.% fiber loading for both composites. The surface functionality of the fiber was improved by giving alkali treatment. Maleic anhydride-grafted-polystyrene (MA-g-PS) was prepared and used as a compatibiliser. The effect of MA-g-PS on the composites was investigated with respect to mechanical properties, morphology and dynamic mechanical properties. The compatibiliser loading was varied from 0 to 2 wt.%. The properties were enhanced significantly in the case of treated and untreated fibre composites at a compatibiliser loading of 0.75 wt.%. SEM analysis confirmed better bonding between the fibre and the matrix. Dynamic mechanical studies showed that the storage modulus at room temperature improved for treated fibre composites in the presence of compatibiliser. In the case of 90/10 PS/SBR composites, the addition of short Nylon-6 fibres at 1 wt.% loading improved the tensile modulus, flexural properties and impact strength while the tensile strength was marginally reduced. The surface treated fibers along with compatibiliser at 0.5 wt.% improved the tensile properties, flexural properties and impact strength. DMA reveale that the storage modulus at room temperature was better for composites containing untreated fibre and the compatibiliser. In the case of 90/22 PS/WTR blends, 1 wt.% unmodified fibre and 0.5 wt.% RFL-coated fibres improved tensile modulus, flexural properties and impact strength. Tensile strength was improved marginally. The surface treatment of Nylon fibre and the addition of compatibiliser at 0.5 wt.% enhanced the tensile properties, flexural properties and impact strength. The dynamic mechanical analysis showed that the storage modulus at room temperature was better for untreated fibre composites in conjunction with the compatibiliser. The thermal stability of PS/NR was studied by TGA. Thermal stability of the blends improved with dynamic vulcanisation and with the incorporation of RFL-coated Nylon fibres. The untreated and partially hydrolyzed fibre composites in conjunction with the compatibiliser enhanced the thermal stability. Kinetic studies showed that the degradation of the blends and the composites followed first order kinetics.

Modification of Phenol Formaldehyde Resin for Improved Mechanical Properties

Phenolic resins suffer from the presence of microvoids on curing. This often leads to less than satisfactory properties in the cured resin. This disadvantage has limited the use of phenolic resins to some extent. This study is an attempt to improve the mechanical properties of the phenolic resol resins by chemical modification aimed at reducing the microvoid population. With this end in view various themoset resins synthesised under predetennined conditions have been employed for modifying phenolic resols. Such resins include unsaturated polyester, epoxy and epoxy novolac prepolymers. The results establish the effectiveness of these resins for improving the mechanical properties of phenolics. Experimental and analytical techniques used include FTIR, DMA, TGA, SEM and mechanical property evaluation. While most of the modifier resins employed give positive results the effect of adding UP is found to be surprising as well as impressive.

High Styrene–Rubber Ionomers, an Alternative to Thermoplastic Elastomers

High styrene rubber ionomers were prepared by sulfonating styrene–butadiene rubber of high styrene content (high styrene rubber) in 1,2-dichloroethane using acetyl sulfate reagent, followed by neutralization of the precursor acids using methanolic zinc acetate. The ionomers were characterized using X-ray fluorescence spectroscopy, Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR), dynamic mechanical analysis (DMA), and also by the evaluation of mechanical properties. The FTIR studies of the ionomer reveal that the sulfonate groups are attached to the benzene ring. The NMR spectra give credence to this observation. Results of DMA show an ionic transition (Ti) in addition to glass–rubber transition (Tg). Incorporation of ionic groups results in improved mechanical properties as well as retention of properties after three cycles of processing

Epoxy-modiWed, unsaturated polyester hybrid networks

Hybrid polymer networks (HPNs) based on unsaturated polyester resin (UPR) and epoxy resins were synthesized by reactive blending. The epoxy resins used were epoxidised phenolic novolac (EPN), epoxidised cresol novolac (ECN) and diglycidyl ether of bisphenol A (DGEBA). Epoxy novolacs were prepared by glycidylation of the novolacs using epichlorohydrin. The physical, mechanical, and thermal properties of the cured blends were compared with those of the control resin. Epoxy resins show good miscibility and compatibility with the UPR resin on blending and the co-cured resin showed substantial improvement in the toughness and impact resistance. Considerable enhancement of tensile strength and toughness are noticed at very low loading of EPN. Thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA) and diVerential scanning calorimetry (DSC) were employed to study the thermal properties of the toughened resin. The EPN/ UPR blends showed substantial improvement in thermal stability as evident from TGA and damping data. The fracture behaviour was corroborated by scanning electron microscopy (SEM). The performance of EPN is found to be superior to other epoxy resins