A simple criterion to predict the glass forming ability of metallic alloys

A new and simple criterion with which to quantitatively predict the glass forming ability (GFA) of metallic alloys is proposed. It was found that the critical cooling rate for glass formation (R-C) correlates well with a proper combination of two factors, the minimum topological instability (lambda(min)) and the Delta h parameter, which depends on the average work function difference (Delta phi) and the average electron density difference (Delta n(ws)(1/3)) among the constituent elements of the alloy. A correlation coefficient (R-2) of 0.76 was found between R-c and the new criterion for 68 alloys in 30 different metallic systems. The new criterion and the Uhlmann's approach were used to estimate the critical amorphous thickness (Z(C)) of alloys in the Cu-Zr system. The new criterion underestimated R-C in the Cu-Zr system, producing predicted Z(C) values larger than those observed experimentally. However, when considering a scale factor, a remarkable similarity was observed between the predicted and the experimental behavior of the GFA in the binary Cu-Zr. When using the same scale factor and performing the calculation for the ternary Zr-Cu-Al, good agreement was found between the predicted and the actual best GFA region, as well as between the expected and the observed critical amorphous thickness. (C) 2012 American Institute of Physics. [doi:10.1063/1.3676196]

Sintesi e caratterizzazione di sistemi catalitici a base di pd-cu e loro utilizzo nella reazione di idrodeclorurazione di molecole clorofluorurate

Questo lavoro di tesi ha avuto come obiettivo quello di individuare e studiare diverse strategie di sintesi per la preparazione di catalizzatori a base di Pd-Cu supportati su materiali mesoporosi a basi di SiO2. Queste strategie sono state mirate a migliorare: -Distribuzione della fase metallica attiva e la sua accessibilità; -Formazione della fase mista Pd-Cu; -Dimensione delle specie metalliche sulla superficie; -Differenti caratteristiche morfologiche del supporto. I diversi catalizzatori preparati sono stati poi testati sulla reazione di idrodeclorurazione del 1,2-dicloro-1,1,2-trifluoro-2-(triflurometossi)etano (AM), svolta in fase gas con idrogeno a pressione atmosferica, con lo scopo di ottenere il composto insaturo corrispondente 1,1,2-trifluoro-2-(trifluorometossi)etene (MVE). Attualmente, il processo industriale per la produzione di MVE, è condotto con l’utilizzo di quantità stechiometriche di Zn in dimetilformammide; questo processo a causa delle quantità stechiometriche di ZnCl2 prodotto e dell'elevato consumo di solvente tossico risulta assai dispendioso dal punto di vista economico ed ambientale. La tipologia di materiali microporosi, già investigata, può limitare l'efficienza verso substrati ingombranti, è quindi interessante investigare catalizzatori con dimensione dei pori mesoporosi a base di silice; in particolare sono stati analizzati MCM-41 e silice amorfa GRACE® DAVICAT - 1401. In particolare, durante il lavoro di tesi sono stati sviluppati i seguenti argomenti: 1.Studio degli effetti della metodologia di sintesi e del contenuto metallico sui parametri chimico-fisici e catalitici dei sistemi a base di Pd-Cu supportati su MCM-41 e GRACE® DAVICAT - 1401; 2.Ottimizzazione del processo di sintesi dei supporti di MCM-41, ponendo attenzione alle quantità dei reagenti utilizzati, alla metodologia di eliminazione del templante e al tempo di trattamento idrotermale; 3.Ottimizzazione del processo di sintesi dei sistemi catalitici a base di Pd-Cu, al fine di ottenere una fase attiva costituita da particelle con dimensioni ridotte composte da una fase mista Pd-Cu.

Edge-to-edge matching model for predicting orientation relationships and habit planes-the improvements

The edge-to-edge matching model has been further developed along with the Cu/Cr system as an example. The conditions for zigzag atom rows to be matching directions are included and the critical value of interatomic spacing misfit along matching directions and the critical value of d-value mismatch between matching planes are proposed in the new version of the model. (c) 2005 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Inhibition of cell-wall autolysis and pectin degradation by cations

Modification of cell wall components such as cellulose, hemicellulose and pectin plays an important role in cell expansion. Cell expansion is known to be diminished by cations but it is unknown if this results from cations reacting with pectin or other cell wall components. Autolysis of cell wall material purified from bean root (Phaseolus vulgaris L.) occurred optimally at pH 5.0 and released mainly neutral sugars but very little uronic acid. Autolytic release of neutral sugars and uronic acid was decreased when cell wall material was loaded with Ca, Cu, Sr, Zn, Al or La cations. Results were also extended to a metal-pectate model system, which behaved similarly to cell walls and these cations also inhibited the enzymatic degradation by added polygalacturonase (EC 3.2.1.15). The extent of sugar release from cation-loaded cell wall material and pectate gels was related to the degree of cation saturation of the substrate, but not to the type of cation. The binding strength of the cations was assessed by their influence on the buffer capacity of the cell wall and pectate. The strongly bound cations (Cu, Al or La) resulted in higher cation saturation of the substrate and decreased enzymatic degradability than the weakly held cations (Ca, Sr and Zn). The results indicate that the junction zones between pectin molecules can peel open with weakly held cations, allowing polygalacturonase to cleave the hairy region of pectin, while strongly bound cations or high concentrations of cations force the junction zone closed, minimising enzymatic attack on the pectin backbone. (C) 2004 Elsevier SAS. All rights reserved.

Microstructure control in Sn-0.7mass%Cu alloys

Soldering alloys based oft the Sn-Cu alloy system are amongst the most favourable lead-free alternatives due to a range of attractive properties. Trace additions of Ni have been found to significantly improve the soldering characteristics of these alloys (reduced bridging etc.). This paper examines the mechanisms underlying the improvement in soldering properties of Sn-0.7 mass%Cu eutectic alloys modified with concentrations of Ni ranging front 0 to 1000 ppm. The alloys were investigated by thermal analysis during solidification, as well as optical/SEM microanalyses of fully solidified samples anti samples quenched during solidification. It is concluded that Ni additions dramatically alter the nucleation patterns and solidification behaviour of the Sn-Cu6Sn5 eutectic anti that these changes are related to the superior soldering characteristics of the Ni-modified Sn-0.7 mass%Cu alloys.

Interrogation of a sonogashira cross-coupling of 8-bromoguanosine with phenylacetylene on amberlite:evidence for Pd/Cu ion binding and propagation of Pd/Cu nanoparticles

The reactivity of Amberlite (IRA-67) base "heterogeneous" resin in Sonogashira cross-coupling of 8-bromoguanosine 1 with phenylacetylene 3 to give 2 has been examined. Both 1 and 2 coordinate to Pd and Cu ions, which explains why at equivalent catalyst loadings, the homogeneous reaction employing triethylamine base is poor yielding. X-ray photo-electron spectroscopy (XPS) has been used to probe and quantify the active nitrogen base sites of the Amberlite resin, and postreaction Pd and Cu species. The Pd2Cl3(PPh)2 precatalyst and CuI cocatalyst degrade to give Amberlite-supported metal nanoparticles (average size ∼2.7 nm). The guanosine product 2 formed using the Amberlite Pd/Cu catalyst system is of higher purity than reactions using a homogeneous Pd precatalyst, a prerequisite for use in biological applications. Copyright © Taylor and Francis Group, LLC.

Densificação e microestrutura de um compósito Mo-Cu preparado a partir de um pó de heptamolibidato de amônia e cobre

The Cu-Mo system is a composite used in the electrical industry as material for electrical contact and resistance welding electrode as well as the heat sink and microwave absorber in microelectronic devices. The use of this material in such applications is due to the excellent properties of thermal and electrical conductivity and the possibility of adjustment of its coefficient of thermal expansion to meet those of materials used as substrates in the semiconductor micoreletrônic industry. Powder metallurgy through the processes of milling, pressing shaping and sintering is a viable technique for consolidation of such material. However, the mutual insolubility of both phases and the low wettability of liquid Cu on Mo impede its densification. However, the mutual insolubility of both phases and the low wettability of liquid Cu on Mo impede its densification. The mechanical alloying is a technique for preparation of powders used to produce nanocrystalline composite powder with amorphous phase or extended solid solution, which increases the sinterability immiscible systems such as the Mo-Cu. This paper investigates the influence of ammonium heptamolybdate (HMA) and the mechanical alloying in the preparation of a composite powder HMA-20% Cu and the effect of this preparation on densification and structure of MoCu composite produced. HMA and Cu powders in the proportion of 20% by weight of Cu were prepared by the techniques of mechanical mixing and mechanical alloying in a planetary mill. These were milled for 50 hours. To observe the evolution of the characteristics of the particles, powder samples were taken after 2, 10, 15, 20, 30 and 40 hours of milling. Cylindrical samples 5 to 8 mm in diameter and 3 to 4 mm thickness were obtained by pressing at 200 MPa to the mixed powders so as to ground. These samples were sintered at 1200 ° C for 60 minutes under an atmosphere of H2. To determine the effect of heating rate on the structure of the material during the decomposition and reduction of HMA, rates of 2, 5 and 10 ° C / min were used .. The post and the structures of the sintered samples were characterized by SEM and EDS. The density of the green and sintered bodies was measured using the geometric method (weight / volume). Vickers microhardness with a load of 1 N for 15 s were performed on sintered structures. The density of the sintered structures 10 ° C / min. reached 99% of theoretical density, how the density of sintered structures to 2 ° C / min. reached only 90% of the theoretical density

Characterisation of soluble components and PAH in PM10 atmospheric particulate matter in Brisbane

Fours sets of PM10 samples were collected in three sites in SEQ from December 2002 to August 2004. Three of these sets of samples were collected by QLD EPA as a part of their regular air monitoring program at Woolloongabba, Rocklea and Eagle Farm. Half of the samples were used in this study for the analysis of water-soluble ions, which are Na+, K+, Mg2+, Ca2+, NH4 +, Cl-, NO3 -, SO4 2-, F-, Br-, NO2 -, PO4 -3 and the other half was retained by QLD EPA. The fourth set of samples was collected at Rocklea, specifically for this study. A quarter of the samples obtained from this set of samples were used to analyse water-soluble ions; a quarter of the sample was used to analyse Pb, Cu, Al, Fe, Mn and Zn; and the rests were used to analyse US EPA 16 priority PAHs. The water-soluble ions were extracted ultrasonically with water and the major watersoluble anions as well as NH4 + were analysed using IC. Na+, K+, Mg2+, Ca2+ Pb, Cu, Al, Fe, Mn and Zn were analysed using ICP-AES while PAHs were extracted by acetonitrile and analysed using HPLC. Of the analysed water-soluble ions, Cl-, NO3 -, SO4 2-, Na+, K+, Mg2+ and Ca2+ were high in concentration and determined in all the samples. F-, Br-, NO2 -, PO4 -3 and NH4 + ions were lower in concentration and determined only in some samples. Na+ and Cl- were high in all samples indicating the importance of a marine source. Principal Component Analysis (PCA) was used to examine the temporal variations of the water-soluble ions at the three sites. The results indicated that there was no major difference between the three sites. However, comparing the average concentrations of ions and Cl-/Na+ it was concluded that Woolloongabba had more marine influence than the other sites. Al, Fe and Zn were detected in all samples. Al and Fe were high in all samples indicating the significance of a source of crustal matter. Cu, Mn and Pb were in low concentrations and were determined only in some samples. The lower Pb concentrations observed in the study than in previous studies indicate that the phasing-out of leaded petrol had an appreciable impact on Pb levels in SEQ. This study reports for the first time, simultaneous data on the water-soluble, metal ion and PAH levels of PM10 aerosols in Brisbane, and provides information on the most likely sources of these chemical species. Such information can be used alongside those that already exist to formulate PM10 pollution reduction strategies for SEQ in order to protect the community from the adverse effects of PM pollution.

Investigations of superconducting bismuth cuprates of the general formula Bi2-xPbx(Ca,Sr,Y)n 1 Cun O2n 4 δ

In the (Bi,Pb)-Sr-Cu-O system we have examined many compositions which are either metallic or semiconducting. In the Bi2-xPbx(Ca, Sr)n+1 Cun O2n+4+δ system, we have established the superconducting properties of the n = 1 to 4 members. The Tc increases from n = 1 to 3 and does not increase further when n = 4. In Bi2Ca1-x,YxSr2Cu2Oy, the Tc decreases with increase in x.

Low-temperature synthesis of bismuth cuprates

A low temperature aqueous solution preparation under strong alkaline medium is reported for the synthesis of bismuth cuprates. Highly crystalline products were obtained at temperatures around 90 degrees C. Tetragonal Bi2CuO4 appears to be the only stable phase formed in the Bi-Cu-O system under these conditions.

Oriented films of LaNiO3 and other members of the Lan+1NinO3n+1 series, LaCuO3−δ and Pb(Zr0.52Ti0.48)O3, obtained by nebulized spray pyrolysis

The technique of nebulized spray pyrolysis has been explored to find out whether oriented films of certain important oxides can be produced on single-crystal substrates by this relatively gentle method. Starting with acetylacetonate precursors, oriented films of metallic LaNiO3 containing nearly spherical grains (30 nm) have been obtained. Films of near-stoichiometric La4Ni3O10 and La3Ni2O7 showing metallic conductivity have been obtained by this method. This is indeed gratifying since it is difficult to prepare monophasic and stoichiometric bulk samples of these materials. Films of La2NiO4 show the expected semiconducting behavior. In the La-Cu-O system, starting with acetylacetonates, we have obtained films mainly comprising semiconducting La2Cu2O5, which is generally difficult to prepare in bulk form. More interestingly, nebulized spray pyrolysis gives excellent stoichiometric films of Pb(Zr0.52Ti0.48)O-3 consisting of nearly spherical grains (30 nm) which show ferroelectric behavior. The present investigation demonstrates that nebulized spray pyrolysis provides a useful and desirable route to deposite oriented films of complex oxide materials on single-crystal substrates.

Effect of Constant and Cyclic Current Stressing on the Evolution of Intermetallic Compound Layers

In this paper the effects of constant and cyclic power loads on the evolution of interfacial reaction layers in lead-free solder interconnections are presented. Firstly, the differences in the growth behavior of intermetallic compound (IMC) layers at the cathode and anode sides of the interconnections are rationalized. This is done by considering the changes in the intrinsic fluxes of elements owing to electromigration as well as taking into account the fact that the growth of Cu3Sn and Cu6Sn5 are coupled via interfacial reactions. In this way, better understanding of the effect of electron flux on the growth of each individual layer in the Cu-Sn system can be achieved. Secondly, it is shown that there is a distinct difference between steady-state current stressing (constant current, constant temperature) and power cycling with alternating on- and off-cycle periods (accompanied by a change of temperature). The reasons behind the observed differences are subsequently discussed. Finally, special care is taken to ensure that the current densities are chosen in such a way that there is no risk for even partial melting of the solder interconnections.

铜-铝扩散焊及拉伸的分子动力学模拟

采用分子动力学方法模拟了铜-铝扩散焊过程,分析了理想平面铜-铝试件(001)晶面间扩散焊的过渡层厚度,并利用径向分布、键对分析方法分析了在不同的降温速率下过渡层的结构变化.降温速率大时,过渡层保持原有无序结构,降温速率小时,过渡层从无序结构向面心立方结构转变.还对扩散焊后的铜-铝试件进行了拉伸模拟,并与尺寸大小相近的单晶铜和单晶铝的拉伸模拟结果进行比较.结果发现焊接后的强度比单晶铝和单晶铜的强度都要小,最大应变值也小.

A Thermodynamic Constitutive Model for Stress Induced Phase Transformation in Shape Memory Alloys

In this paper a thermodynamic constitutive model is developed for stress induced phase transformation in single crystalline and polycrystalline shape memory alloys (SMAs). Volume fractions of different martensite variants are chosen as internal variables to describe the evolution of microstructure state in the material. This model is then used in prediction the transformation behavior of a SMA (Cu-Al-Zn-Mn) under complex thermomechanical load (including complete and incomplete transformation in mechanical cycling, and proportional/non-proportional loading). (C) 2002 Elsevier Science Ltd. All rights reserved.

Evaluación de rendimiento en el cultivo de soja aplicando fosfitos y micronutrientes

Resumen: Lo que se pretende reflejar en este trabajo es la importancia del uso de fosfitos y micronutrientes en el cultivo de soja. El cultivo de esta oleaginosa se ha ido incrementando a lo largo de los últimos años de la mano de la siembra directa, de la genética, del paquete tecnológico para su implantación y protección y del manejo realizado por los profesionales del agro. Este crecimiento en superficie en detrimento de los demás cultivos extensivos que deberían formar parte de la rotación, hizo de la oleaginosa en varias zonas un monocultivo. Esto sumado a la falta de rotación de activos fue generando problemas dentro de los cuales podemos citar: malezas de difícil control, alta presión de enfermedades y plagas. La fertilización, en la generalidad de los casos, está por debajo de los requerimientos por tonelada lograda, generando extracción de macro y micro elementos y agotando los niveles de estos mismos en el perfil edáfico. El aporte de macronutrientes está dado principalmente por fósforo (no en todas las zonas). Asimismo, en algunas zonas dependiendo las deficiencias agregan potasio, azufre y calcio. Así todo se fertiliza por debajo de los rindes objetivos perseguidos, lo cual se comprende que cuando los cultivos superan los mismos, se está haciendo una extracción mayor del sistema suelo que los aportes generados. Lo ideal es realizar un muestreo de cada lote y ambiente, verificar los niveles de nutrientes disponibles y fertilizar pensado en contemplar el rinde perseguido y entregar al sistema suelo un poco más, de manera de hacer una producción no solo rentable en el corto plazo sino sustentable en el tiempo, cuidando el capital suelo. Los macro y meso nutrientes son aportados vía fertilización de base o fondo y la manera más eficiente de aportar los micro elementos, es vía fertilización foliar. Los fosfitos son desde el punto de vista sanitario, la herramienta ideal y complementaria de los fungicidas. Son derivados del ácido fosforoso y tienen dos formas de acción contra los hongos fitopatógenos. Una forma indirecta, aumentando el nivel de defensas de las plantas o Fitoalexinas, impidiendo que las esporas germinen en tejido susceptible. Y una acción directa como fungicidas contra los pseudohongos u Oomicetes. Recordar que los triazoles son una excelente herramienta para controlar hongos verdaderos (Ascomicetes, Basidiomicetes y Deuteromicetes) al igual que las estrobirulinas, pero ambos activos no son específicos para Oomicetes. Generalmente, los fosfitos van combinados con diferentes cationes, que a su vez le confieren diferentes modos de actuar, por ejemplo el fosfito de cobre, actúa desde el punto de vista sanitario elevando las defensas y además presenta el catión cobre como elemento fungistático y bactericida. En el mercado existen diferentes tipos de fosfitos y formas de acción según catión acompañante. Hay fosfitos de Cu, Al, K, Mn, Ca, ect. Uno de los puntos más importantes de los fosfitos es que se translocan vía xilema y floema, llegando rápidamente a los diferentes sitios de la planta. Los fungicidas a diferencia de los fosfitos no pueden realizar la misma labor. Los fungicidas protegen al follaje tratado, pero no al nuevo emergente y el movimiento de los activos se da desde donde impacta la gota asperjada en sentido ascendente, ósea acrópeto, mientras que los fosfitos al recorrer toda la planta realizan una protección integral de la misma. Además, los fosfitos, presentan efecto sinérgico con los fungicidas potenciando la acción de estos. Colaboran en el engrosamiento de tejidos de raíz y tallo, fortaleciéndolos contra el ataque de patógenos. Son de rápida absorción e impactan positivamente en la formación de destinos, como flores y frutos, y fuentes de reservas como raíz. No disponen de valor nutricional para los cultivos extensivos anuales, ya que presentan un tiempo de degradación que excede al desarrollo de estos mismos. Este trabajo, se desarrolla implementando el diseño completamente aleatorio, en el cual la variable respuesta (rendimiento) puede depender de la influencia de un único factor (aplicación de fitoestimulantes), de forma que el resto de las causas de variación se engloban en el error experimental. Se compara los tratamientos contra el testigo, y se hace análisis de la variancia con un nivel de significación del 5%. Dentro de la variable respuesta se analiza el rendimiento en kg/ha. Teniendo en cuenta para este análisis los siguientes datos: 1) Número de granos 2) Peso de 1000 granos Este ensayo consta de cuatro tratamientos y tres repeticiones en un mismo estado fenológico (V10 R2) del cultivo.