A novel postharvest rot of okra pods caused by Rhizoctonia solani in Brazil

Okra pods with unusual brown lesions and rot were collected in a local supermarket in Brasília DF. The objective of this paper was to characterize the causal agent, to fulfill Koch's postulates and to determine some conditions conducive to disease. The pathogen was identified as Rhizoctonia solani based on morphological characteristics which fitted the fungus description, such as pale to brown hyphae, with nearly right-angled side branches constricted at the base, hyphal cells 6-10 µm wide with a septum near the base. Five isolates were obtained from infected pods and identified as AG 1-IB anastomosis group. Wounded or unwounded okra pods cv. Santa Cruz 47 were inoculated with mycelium disks of R. solani and kept in humid chambers at 12 ºC or 25 ºC. After seven days at 25 ºC, both wounded and unwounded pods were completely rotted and brown, while those kept at 12 ºC showed small lesions ranging from 0.6 to 1.0 mm only in wounded pods. The pathogen was able to grow in different materials used for assembling crates and packs of horticultural products, such as pinewood, corrugated carton, plastic, Styrofoam and newspaper sheets when kept in humid chambers (24 ºC, 96 % RH). The disease occurrence can be related to careless handling practices and to the transmission of R. solani propagules by infected plant debris or soil particles. This is the first report of Rhizoctonia solani causing postharvest rot in okra pods in Brazil.

Fatigue analysis of brackets with and without scallop for bridge and other deck structure using effective notch stress.

Due to functional requirement of a structural detail brackets with and without scallop are frequently used in bridges, decks, ships and offshore structure. Scallops are designed to serve as passage way for fluids, to reduce weld length and plate distortions. Moreover, scallops are used to avoid intersection of two or more welds for the fact that there is the presence of inventible inherent initial crack except for full penetrated weld and the formation of multi-axial stress state at the weld intersection. Welding all around the scallop corner increase the possibility of brittle fracture even for the case the bracket is not loaded by primary load. Avoiding of scallop will establish an initial crack in the corner if bracket is welded by fillet welds. If the two weld run pass had crossed, this would have given a 3D residual stress situation. Therefore the presences and absence of scallop necessitates the 3D FEA fatigue resistance of both types of brackets using effective notch stress approach ( ). FEMAP 10.1 with NX NASTRAN was used for the 3D FEA. The first and main objective of this research was to investigate and compare the fatigue resistance of brackets with and without scallop. The secondary goal was the fatigue design of scallops in case they cannot be avoided for some reason. The fatigue resistance for both types of brackets was determined based on approach using 1 mm fictitiously rounded radius based on IIW recommendation. Identical geometrical, boundary and loading conditions were used for the determination and comparison of fatigue resistance of both types of brackets using linear 3D FEA. Moreover the size effect of bracket length was also studied using 2D SHELL element FEA. In the case of brackets with scallop the flange plate weld toe at the corner of the scallop was found to exhibit the highest and made the flange plate weld toe critical for fatigue failure. Whereas weld root and weld toe at the weld intersections were the highly stressed location for brackets without scallop. Thus weld toe for brackets with scallop, and weld root and weld toe for brackets without scallop were found to be the critical area for fatigue failure. Employing identical parameters on both types of brackets, brackets without scallop had the highest except for full penetrated weld. Furthermore the fatigue resistance of brackets without scallop was highly affected by the lack of weld penetration length and it was found out that decreased as the weld penetration was increased. Despite the fact that the very presence of scallop reduces the stiffness and also same time induce stress concentration, based on the 3D FEA it is worth concluding that using scallop provided better fatigue resistance when both types of brackets were fillet welded. However brackets without scallop had the highest fatigue resistance when full penetration weld was used. This thesis also showed that weld toe for brackets with scallop was the only highly stressed area unlike brackets without scallop in which both weld toe and weld root were the critical locations for fatigue failure when different types of boundary conditions were used. Weld throat thickness, plate thickness, scallop radius, lack of weld penetration length, boundary condition and weld quality affected the fatigue resistance of both types of brackets. And as a result, bracket design procedure, especially welding quality and post weld treatment techniques significantly affect the fatigue resistance of both type of brackets.

Tuplakuori-rakenne eristettyihin muoviputkiin

Eristettyjen muoviputkien kuljetus- tai asennusvaiheessa on mahdollista, että putken suojakuori rikkoutuu mekaanisen iskun vaikutuksesta ja putken sisään pääsee vettä. Huonoimmassa tapauksessa vesi pääsee etenemään suojakuoren ja eristekerroksen välissä talon sisälle ja aiheuttaa mittavat kosteusvahingot. Tämän diplomityön tarkoituksena oli selvittää, onko eristetylle muoviputkelle mahdollista toteuttaa tuotantotaloudellisesti tuplakuori-rakenne. Tuplakuoren tarkoituksena oli tässä työssä estää putken sisärakenteisiin päässeen veden eteneminen putken pitkittäissuunnassa. Diplomityössä käsiteltiin muutamia vaihtoehtoisia ratkaisuja toteuttaa tuplakuori-rakenne joista lopulta päädyttiin keskittymään muovikalvon käyttöön. Muovikalvon käytöllä oli lähinnä kaksi tarkoitusta. Tärkeimpänä oli saada muovikalvo sulamaan eristekerroksen ja suojakuoren väliin. Tällöin sulanut muovikalvo toimisi liiman tavoin ja hitsaisi eristekerroksen ja suojakuoren toisiinsa kiinni. Näin veden eteneminen eristekerroksen ja suojakuoren välissä saataisiin estetyksi. Muovikalvo oli myös tarkoitus kiristää eristepaketin päälle niin kireälle, että eristepaketin halkaisijaa saataisiin pienennettyä. Muovikalvon käyttöön perehdyttiin suorittamalla tuotantolinjalla koeajoja. Koeajoissa kokeiltiin erilaisia ja erikokoisia putkituotteita erilaisilla tuotantoparametreilla. Näin pyrittiin löytämään parhaat parametrit ja arvot, joilla muovikalvoa pystyttäisiin tulevaisuudessa käyttämään jatkuvassa tuotannossa. Koeajojen tuloksista voitiin havaita, että kalvoitetut putkituotteet käyttäytyivät tuotannossa hyvin eri tavoin.

PYRENE MORPHOLOGY OF THREE SPECIES OF Byrsonima Rich. ex Kunth (Malpighiaceae)1

ABSTRACT The species of the genus Byrsonima Rich. ex Kunth are of great medicinal and economic importance, but they are still poorly studied with respect to their propagules. This study describes, illustrates and comparse morphological aspects of the pyrenes of Byrsonima crassifolia (L.) Kunth, Byrsonima verbascifolia (L.) DC. and Byrsonima coccolobifolia Kunth occurring in areas of savannah of Boa Vista, Roraima. The pyrenes are globoid, obovoid to ovoid, with endocarp dark brown in color, with a corrugated and reticulate surface and corneous consistency. They possess distinctly septate locules with or without seeds, the outer wall of which are dark brown in color with corneous consistency and thin black inner walls also with corneous consistency. The number of locules and seeds per pyrene among the species varies. The seeds are exalbuminous, globoid, obovoid to ovoid, with a thin, smooth integument and are light-brown in color. They have radicular lobes and hypostasis. The embryo is continuous and axial with cylindrical spirally rolled cotyledons. The diameter of pyrenes of Byrsonima crassifolia is greater than in the other two species. The pyrenes of B. coccolobifolia are longer and heavier, while those of B. verbascifolia are lighter and the seeds have greater lengths, widths and thickness compared to the other two species studied. The three species have similar morphologies, differing in the size and weight of pyrenes and seeds.

Anaerobic co-digestion of crude glycerin and starch industry effluent

The Brazil's Biodiesel Production and Use Program introduces biodiesel in the Brazilian energy matrix, bringing along the perspective of a growth of the glycerin offer, co-product generated in the proportion of 10 kg for each 100 L of biodiesel. The aim of this study was to evaluate the addition of crude glycerin in the anaerobic digestion of cassava starch industry effluent (cassava wastewater), in a horizontal semi-continuous flow reactor of one phase in laboratory scale. It was used a reactor with a 8.77 L of useful volume, a medium support for corrugated conduit of polyvinyl chloride (PVC), temperature of 261 ºC, fed with cassava wastewater and glycerin, with hydraulic detention times of 4 and 5 days and increasing volumetric organic load of 3.05; 9.32; 14.83 and 13.59 g COD L-1 d-1, obtained with the addition of glycerin at 0; 2; 3 and 2% (v/v), respectively. The average removal efficiencies of TS and TVS were decreasing from the addition of glycerin to the cassava wastewater, averaging 81.19 to 55.58% for TS and 90.21 to 61.45% for TVS. The addition of glycerin at 2% increased the biogas production compared to the control treatment, reaching 1.979 L L-1 d-1. The biogas production as a function of the consumed COD was higher for the control treatment than for the treatments with addition of glycerin, which indicates lower conversion of organic matter into biogas.

Horizontal pressures in cylindrical metal silos and comparison with different international standards

The focus of this research was to evaluate the horizontal pressures on a cylindrical metal silo of corrugated walls and flat bottom with 1.82m diameter and 5.4m high, and to compare the values with those obtained theoretically by the ISO 11697, EP 433 and AS 3774 standards. The silo was symmetrically filled and constant speed with wheat cv. soft red for two different height/diameter ratios (H/D) and was unloaded through three orifices with a diameter of 71.6mm, one concentric and two eccentrics. Horizontal pressures were measured on the walls of the silo at three positions using hydraulic type pressure cells. The results showed that shortly after the start of the unloading, there was a mass flow above the quota of H/D = 1.2, whereas below this quota funnel flow occurred. It can be said that the EP 433 standard was more appropriate to predict horizontal pressures in silos in H/D ratio = 1.0, with eccentric unloading. For the H/D ratio = 1.5, AS 3774 standard was the one that produced values closer to the experimental.

Proliferative enteropathy (Lawsonia intracellularis) outbreak in rabbits in Brazil

An outbreak of Lawsonia intracellularis infection in rabbits, which occurred in 1988 in Rio de Janeiro state, Brazil, is reported. The disease had an acute course (24-48 hours) with clinical signs characterized by brownish or green diarrhea and dehydration. Occasionally, the animals died one day after the onset of diarrhea, without showing any other clinical signs. At necropsy, the ileum was prominent, firm and had a thickened wall; it was dilated in the caudal direction and had a somewhat reticulated appearance, perceptible through the serosa. The thickened mucous membrane had finely corrugated aspect and a shiny surface. The ileocecal valve and surrounding areas were slightly edematous and irregular. The Peyer's patches were sometimes more evident. There was moderate enlargement of the mesenteric lymph nodes. The histological examination revealed different degrees of hyperplasia of the epithelial cells of intestinal crypts consisting of poorly differentiated, hyperchromatic cells with high mitotic index, arranged in a pseudostratified layer which, in some cases, reached the apical portions of the villi. The inflammatory infiltrate between the hyperplastic epithelial cells was composed of lymphocytes, plasma cells, macrophages, some eosinophils and globular leukocytes. Silver impregnation revealed large numbers of bacteria with morphology of the genus Lawsonia in the apical pole of cryptal enterocytes. These bacteria reacted positively to a Lawsonia intracellularis polyclonal antibody by the avidin-biotin immunohistochemistry method.

Characterisation of Laser Beam and Paper Material Interaction

It is known already from 1970´s that laser beam is suitable for processing paper materials. In this thesis, term paper materials mean all wood-fibre based materials, like dried pulp, copy paper, newspaper, cardboard, corrugated board, tissue paper etc. Accordingly, laser processing in this thesis means all laser treatments resulting material removal, like cutting, partial cutting, marking, creasing, perforation etc. that can be used to process paper materials. Laser technology provides many advantages for processing of paper materials: non-contact method, freedom of processing geometry, reliable technology for non-stop production etc. Especially packaging industry is very promising area for laser processing applications. However, there are only few industrial laser processing applications worldwide even in beginning of 2010´s. One reason for small-scale use of lasers in paper material manufacturing is that there is a shortage of published research and scientific articles. Another problem, restraining the use of laser for processing of paper materials, is colouration of paper material i.e. the yellowish and/or greyish colour of cut edge appearing during cutting or after cutting. These are the main reasons for selecting the topic of this thesis to concern characterization of interaction of laser beam and paper materials. This study was carried out in Laboratory of Laser Processing at Lappeenranta University of Technology (Finland). Laser equipment used in this study was TRUMPF TLF 2700 carbon dioxide laser that produces a beam with wavelength of 10.6 μm with power range of 190-2500 W (laser power on work piece). Study of laser beam and paper material interaction was carried out by treating dried kraft pulp (grammage of 67 g m-2) with different laser power levels, focal plane postion settings and interaction times. Interaction between laser beam and dried kraft pulp was detected with different monitoring devices, i.e. spectrometer, pyrometer and active illumination imaging system. This way it was possible to create an input and output parameter diagram and to study the effects of input and output parameters in this thesis. When interaction phenomena are understood also process development can be carried out and even new innovations developed. Fulfilling the lack of information on interaction phenomena can assist in the way of lasers for wider use of technology in paper making and converting industry. It was concluded in this thesis that interaction of laser beam and paper material has two mechanisms that are dependent on focal plane position range. Assumed interaction mechanism B appears in range of average focal plane position of 3.4 mm and 2.4 mm and assumed interaction mechanism A in range of average focal plane position of 0.4 mm and -0.6 mm both in used experimental set up. Focal plane position 1.4 mm represents midzone of these two mechanisms. Holes during laser beam and paper material interaction are formed gradually: first small hole is formed to interaction area in the centre of laser beam cross-section and after that, as function of interaction time, hole expands, until interaction between laser beam and dried kraft pulp is ended. By the image analysis it can be seen that in beginning of laser beam and dried kraft pulp material interaction small holes off very good quality are formed. It is obvious that black colour and heat affected zone appear as function of interaction time. This reveals that there still are different interaction phases within interaction mechanisms A and B. These interaction phases appear as function of time and also as function of peak intensity of laser beam. Limit peak intensity is the value that divides interaction mechanism A and B from one-phase interaction into dual-phase interaction. So all peak intensity values under limit peak intensity belong to MAOM (interaction mechanism A one-phase mode) or to MBOM (interaction mechanism B onephase mode) and values over that belong to MADM (interaction mechanism A dual-phase mode) or to MBDM (interaction mechanism B dual-phase mode). Decomposition process of cellulose is evolution of hydrocarbons when temperature is between 380- 500°C. This means that long cellulose molecule is split into smaller volatile hydrocarbons in this temperature range. As temperature increases, decomposition process of cellulose molecule changes. In range of 700-900°C, cellulose molecule is mainly decomposed into H2 gas; this is why this range is called evolution of hydrogen. Interaction in this range starts (as in range of MAOM and MBOM), when a small good quality hole is formed. This is due to “direct evaporation” of pulp via decomposition process of evolution of hydrogen. And this can be seen can be seen in spectrometer as high intensity peak of yellow light (in range of 588-589 nm) which refers to temperature of ~1750ºC. Pyrometer does not detect this high intensity peak since it is not able to detect physical phase change from solid kraft pulp to gaseous compounds. As interaction time between laser beam and dried kraft pulp continues, hypothesis is that three auto ignition processes occurs. Auto ignition of substance is the lowest temperature in which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. Three auto ignition processes appears in range of MADM and MBDM, namely: 1. temperature of auto ignition of hydrogen atom (H2) is 500ºC, 2. temperature of auto ignition of carbon monoxide molecule (CO) is 609ºC and 3. temperature of auto ignition of carbon atom (C) is 700ºC. These three auto ignition processes leads to formation of plasma plume which has strong emission of radiation in range of visible light. Formation of this plasma plume can be seen as increase of intensity in wavelength range of ~475-652 nm. Pyrometer shows maximum temperature just after this ignition. This plasma plume is assumed to scatter laser beam so that it interacts with larger area of dried kraft pulp than what is actual area of beam cross-section. This assumed scattering reduces also peak intensity. So result shows that assumably scattered light with low peak intensity is interacting with large area of hole edges and due to low peak intensity this interaction happens in low temperature. So interaction between laser beam and dried kraft pulp turns from evolution of hydrogen to evolution of hydrocarbons. This leads to black colour of hole edges.

M-käsittelyn vaikutus lastuamalla valmistettavan tuotteen valmistuskustannuksiin

Paremmin lastuttavia M-käsiteltyjä teräksiä on käytetty yrityksissä jo yli 20 vuoden ajan. Ominaisuuksiensa ansiosta M-teräksillä on pystytty pienentämään koneistuskustannuksia ja parantamaan kilpailukykyä. Viime vuosien aikana lastuavat terät ja työstökoneet ovat kuitenkin kehittyneet ja ero M-terästen ja tavanomaisten terästen välillä on voinut kaventua. Tämän diplomityön tavoitteena oli tutkia, saavutetaanko M-teräksen käytöllä taloudellisia etuja nykyaikaisissa konepajaolosuhteissa. Tutkimuksessa vertailtiin M-käsitellyn ja tavanomaisen 42CrMo4 – teräksen koneistusta. Valmistuskokeissa tarkasteltiin terien kulumista, lastun muotoa ja pinnanlaatua. Koekappaleena toimi olakkeellinen kuusiomutteri M64 kierteellä. Tuotteita valmistettiin yli 500 kappaletta ja materiaalia poistettiin noin 2000 kg. Koetulosten perusteella tuotteille laskettiin koneistuskustannukset kuvitteellisessa yrityksessä. Ero materiaalien välillä oli suurin työvaiheissa, joissa lastuaminen oli jatkuvaa. Sisä- ja ulkosorvauksessa M-käsiteltyä terästä lastunneiden terien kestoikä oli noin kaksinkertainen ja kierteen sorvauksessa noin nelinkertainen tavalliseen teräkseen verrattuna. Hakkaavassa työstössä terien kestoikä oli molemmilla materiaaleilla sama. Työssä suoritettujen kokeiden ja kustannuslaskelmien perusteella, käyttämällä M-käsiteltyä terästä voidaan pienentää valmistuskustannuksia. Materiaalien välinen ero korostuu, kun hakkaavaa työstöä on vähän, sarjat ovat suuria ja tuotanto on miehittämätöntä.

Local Web Buckling in Tapered Composite Beams: A Parametric Study

Composite flooring systems supported by tapered (varying web depth) beams are very attractive from an economic point of view. However, the tapered beam sections are fabricated from plate by welding, and are susceptible to imperfection effects. These may interact with the localised compressive stress field that is generated in the web at a slope change in the lower flange to cause local web buckling. A substantial parametric study using a non-linear elasto-plastic finite element program and covering practical ranges of the important parameters including the area of the tension flange, taper slope and web thickness is reported. Moment-rotation relations, peak moments and failure mechanisms have been predicted. The validity of the work is supported by the good correlation obtained between the results of the parametric study and experimental data.

Experimental validation of a 3-D vision-based measurement system applied to robot calibration

One of the problems that slows the development of off-line programming is the low static and dynamic positioning accuracy of robots. Robot calibration improves the positioning accuracy and can also be used as a diagnostic tool in robot production and maintenance. A large number of robot measurement systems are now available commercially. Yet, there is a dearth of systems that are portable, accurate and low cost. In this work a measurement system that can fill this gap in local calibration is presented. The measurement system consists of a single CCD camera mounted on the robot tool flange with a wide angle lens, and uses space resection models to measure the end-effector pose relative to a world coordinate system, considering radial distortions. Scale factors and image center are obtained with innovative techniques, making use of a multiview approach. The target plate consists of a grid of white dots impressed on a black photographic paper, and mounted on the sides of a 90-degree angle plate. Results show that the achieved average accuracy varies from 0.2mm to 0.4mm, at distances from the target from 600mm to 1000mm respectively, with different camera orientations.

Terästankkien valmistusvaiheen kustannus- ja aikataulurakenteen määrittäminen

Diplomityössä tutkittiin erilaisilla loppuasennusmenetelmillä toimitettujen terästank-kien kustannus- ja aikataulurakennetta. Usein terästankit valmistetaan valmiiksi muotoon valssatuista levyistä työmaalla kasaanhitsaamalla. Tämä ei ole ainoa terästankin valmistusvaihtoehto, myös ruuvaus, niittaus, kiilaliitos ja konepajalla suuremmiksi kappaleiksi hitsaus ovat yleisesti käytössä. Terästankkien valmistuskustannuksiin vaikuttavat materiaali, esivalmisteiden työstäminen, kuljetus ja loppuasennus. Tankin valmistusmenetelmä ei merkittävästi vaikuta tankin materiaalikustannuksiin. Materiaalikustannuksiin vaikuttavat eniten käytettävä materiaali ja tankin geometriset ominaisuudet. Tankin esivalmisteiden valmistusaika määräytyy loppuasennusmenetelmästä. Pidempi esivalmistusaika lyhentää loppu-asennusaikaa. Kokonaisena toimitetussa tankissa esivalmistuksen osuus on suurempi kuin hitsatussa tankissa, mutta loppuasennusaika on vain murto-osa hitsattavan tankin loppuasennusajasta. Ruuvattavassa tankissa laippojen hitsaus levyihin lisää esivalmistusaikaa, kun rullattavassa tankissa aikaa vievät vaippalevyjen kasaanhitsaaminen ja rullaaminen. Tankin loppuasennustapa voidaan, etenkin halkaisijaltaan noin 10 m:llä tankeilla, valita kohdemaan mukaan, koska erot valmistuskustannuksissa ovat pieniä eri toimitusmuotojen välillä. Tosin kokonaisen 10 m halkaisijaltaan olevan tankin kuljettaminen ei aina ole mahdollista eikä kannattavaa. Sen sijaan halkaisijaltaan 5 m:llä tankeilla kokonaisena toimittaminen on varteenotettava vaihtoehto. Sopivin tankkivaihtoehto, kokonainen, hitsattava, ruuvattava tai rullattava, tulee miettiä aina tapauskohtaisesti, kohdemaan, hitsausosaamisen, kuljetusmahdollisuuksien ja loppuasennuspaikan mukaan.

Pyörivien koneiden ruuviliitosten mitoitus ja mitoitusohjelman laadinta standardien mukaisesti

Työn tarkoituksena oli löytää pyörivien koneiden ruuviliitosten mitoittamiseen parhaiten soveltuva ja kansainvälisesti tunnettu laskentamenetelmä. Tavoitteena oli laatia luotettava mitoitusohjelma, jota käyttämällä suunnittelijoiden työ nopeutuu ja tulokset ovat yhtenäisiä. Työssä vertaillaan pääasiassa standardien EN 1993-1-8 ja VDI 2230 mukaisia ruuviliitosten mitoitusmenetelmiä. Vertailun perusteella standardin VDI 2230 mukainen systemaattinen laskentamenetelmä soveltuu sähkökoneiden vääntöä välittävien ruuviliitosten mitoittamiseen analyyttisistä menetelmistä parhaiten. Laadittu mitoitusohjelma mitoittaa yksittäisen ruuviliitoksen standardin VDI 2230 mukaisesti, antaen tulokseksi lujuustarkasteluraportin. Lujuustarkasteluraportista käy ilmi projektin tiedot, mitoituksen lähtötiedot, lujuustarkastelut, esikiristysmomentti ja kierteen toiminnallisen osan vähimmäispituus. Kehitetty mitoitusohjelma antaa johdonmukaisia tuloksia, mutta ruuvin nimellisulkohalkaisijan automaattinen valinta ei aina mitoita ruuvia riittävän suureksi, jolloin ruuvin nimellisulkohalkaisija on määritettävä manuaalisesti. Ohjelman käyttäminen on suoraviivaista ja nopeaa kun mitoitetaan pyörähdyssymmetrisiä laippaliitoksia, joihin vaikuttaa ainoastaan vääntömomentti. Jos liitokseen vaikuttaa ruuvien pituusakselien suuntainen voima, on liitoksen pelkistäminen yksittäisestä ruuvista koostuvaksi liitokseksi vaikeampaa ja pelkistämiseen saatetaan tarvita elementti-menetelmää.

Kuparin hitsaus kattavilla laatuvaatimuksilla

Kuparin ja kupariseosten hitsaus eroaa merkittävästi esimerkiksi terästen hitsauksesta. Suuri lämmönjohtavuus, lämpölaajeneminen, pehmeneminen ja kuparin taipumus liuottaa kaasuja sulaan asettavat hitsaukselle haasteita. Kuparia on perinteisesti hitsattu kaasuhitsaamalla ja kaasukaarihitsausprosesseilla, mutta uudemmat menetelmät kuten laserhitsaus, elektronisuihkuhitsaus ja FSW-hitsaus tarjoavat uudenlaisia käyttökohteita korkealla laadulla. ISO 3834-2 asettaa noudatettavat vaatimukset hitsaustoiminnalle laatuvaatimusten ollessa kattavia. Ydinvoimalaitoksella hitsauksessa tulee lisäksi noudattaa Säteilyturvakeskuksen YVL-ohjeita, joissa on määritetty lisävaatimuksia liitosten materiaalivalinnoille, pätevöittämiselle ja tarkastamiselle. Tässä työssä tutkittiin kuparimetallien hitsauksen mahdollisuutta Loviisan ydinvoimalaitoksella juottamisen sijasta siten, että kattavat laatuvaatimukset täyttyisivät. Hitsauskokeissa ja laboratoriotutkimuksissa testattiin hitsausta erilaisilla hitsausaineilla ja hitsausprosesseilla. Koetulosten pohjalta toteutettiin hitsausmenetelmä deoksidoidun kupariputken ja tinapronssilaipan TIG-hitsaukselle.