Fly Ash Soil Stabilization for Non-Uniform Subgrade Soils, Volume II: Influence of Subgrade Non-Uniformity on PCC Pavement Performance, TR-461, 2005

To provide insight into subgrade non-uniformity and its effects on pavement performance, this study investigated the influence of non-uniform subgrade support on pavement responses (stress and deflection) that affect pavement performance. Several reconstructed PCC pavement projects in Iowa were studied to document and evaluate the influence of subgrade/subbase non-uniformity on pavement performance. In situ field tests were performed at 12 sites to determine the subgrade/subbase engineering properties and develop a database of engineering parameter values for statistical and numerical analysis. Results of stiffness, moisture and density, strength, and soil classification were used to determine the spatial variability of a given property. Natural subgrade soils, fly ash-stabilized subgrade, reclaimed hydrated fly ash subbase, and granular subbase were studied. The influence of the spatial variability of subgrade/subbase on pavement performance was then evaluated by modeling the elastic properties of the pavement and subgrade using the ISLAB2000 finite element analysis program. A major conclusion from this study is that non-uniform subgrade/subbase stiffness increases localized deflections and causes principal stress concentrations in the pavement, which can lead to fatigue cracking and other types of pavement distresses. Field data show that hydrated fly ash, self-cementing fly ash-stabilized subgrade, and granular subbases exhibit lower variability than natural subgrade soils. Pavement life should be increased through the use of more uniform subgrade support. Subgrade/subbase construction in the future should consider uniformity as a key to long-term pavement performance.

Development of LRFD Procedures for Bridge Pile Foundations in Iowa Volume III: Recommended Resistance Factors with Consideration of Construction Control and Setup, TR-584, 2012

The Federal Highway Administration (FHWA) mandated utilizing the Load and Resistance Factor Design (LRFD) approach for all new bridges initiated in the United States after October 1, 2007. As a result, there has been a progressive move among state Departments of Transportation (DOTs) toward an increased use of the LRFD in geotechnical design practices. For the above reasons, the Iowa Highway Research Board (IHRB) sponsored three research projects: TR-573, TR-583 and TR-584. The research information is summarized in the project web site (http://srg.cce.iastate.edu/lrfd/). Two reports of total four volumes have been published. Report volume I by Roling et al. (2010) described the development of a user-friendly and electronic database (PILOT). Report volume II by Ng et al. (2011) summarized the 10 full-scale field tests conducted throughout Iowa and data analyses. This report presents the development of regionally calibrated LRFD resistance factors for bridge pile foundations in Iowa based on reliability theory, focusing on the strength limit states and incorporating the construction control aspects and soil setup into the design process. The calibration framework was selected to follow the guidelines provided by the American Association of State Highway and Transportation Officials (AASHTO), taking into consideration the current local practices. The resistance factors were developed for general and in-house static analysis methods used for the design of pile foundations as well as for dynamic analysis methods and dynamic formulas used for construction control. The following notable benefits to the bridge foundation design were attained in this project: 1) comprehensive design tables and charts were developed to facilitate the implementation of the LRFD approach, ensuring uniform reliability and consistency in the design and construction processes of bridge pile foundations; 2) the results showed a substantial gain in the factored capacity compared to the 2008 AASHTO-LRFD recommendations; and 3) contribution to the existing knowledge, thereby advancing the foundation design and construction practices in Iowa and the nation.

Low-Cost Rural Surface Alternatives: Demonstration Project, TR-664, 2015

The goals of this project were to implement several stabilization methods for preventing or mitigating freeze-thaw damage to granular surfaced roads and identify the most effective and economical methods for the soil and climate conditions of Iowa. Several methods and technologies identified as potentially suitable for Iowa were selected from an extensive analysis of existing literature provided with Iowa Highway Research Board (IHRB) Project TR-632. Using the selected methods, demonstration sections were constructed in Hamilton County on a heavily traveled two-mile section of granular surfaced road that required frequent maintenance during previous thawing periods. Construction procedures and costs of the demonstration sections were documented, and subsequent maintenance requirements were tabulated through two seasonal freeze-thaw periods. Extensive laboratory and field tests were performed prior to construction, as well as before and after the two seasonal freeze-thaw periods, to monitor the performance of the demonstration sections. A weather station was installed at the project site and temperature sensors were embedded in the subgrade to monitor ground temperatures up to a depth of 5 ft and determine the duration and depths of ground freezing and thawing. An economic analysis was performed using the documented construction and maintenance costs, and the estimated cumulative costs per square yard were projected over a 20-year timeframe to determine break-even periods relative to the cost of continuing current maintenance practices. Overall, the sections with biaxial geogrid or macadam base courses had the best observed freeze-thaw performance in this study. These two stabilization methods have larger initial costs and longer break-even periods than aggregate columns, but counties should also weigh the benefits of improved ride quality and savings that these solutions can provide as excellent foundations for future paving or surface upgrades.

Evaluation of the Need for Longitudinal Median Joints in Bridge Decks on Dual Structures, TR-661, 2015

The primary objective of this project was to determine the effect of bridge width on deck cracking in bridges. Other parameters, such as bridge skew, girder spacing and type, abutment type, pier type, and number of bridge spans, were also studied. To achieve the above objectives, one bridge was selected for live-load and long-term testing. The data obtained from both field tests were used to calibrate a three-dimensional (3D) finite element model (FEM). Three different types of loading—live loading, thermal loading, and shrinkage loading—were applied. The predicted crack pattern from the FEM was compared to the crack pattern from bridge inspection results. A parametric study was conducted using the calibrated FEM. The general conclusions/recommendations are as follows: -- Longitudinal and diagonal cracking in the deck near the abutment on an integral abutment bridge is due to the temperature differences between the abutment and the deck. Although not likely to induce cracking, shrinkage of the deck concrete may further exacerbate cracks developed from thermal effects. -- Based upon a limited review of bridges in the Iowa DOT inventory, it appears that, regardless of bridge width, longitudinal and diagonal cracks are prevalent in integral abutment bridges but not in bridges with stub abutments. -- The parametric study results show that bridge width and skew have minimal effect on the strain in the deck bridge resulting from restrained thermal expansion. -- Pier type, girder type, girder spacing, and number of spans also appear to have no influence on the level of restrained thermal expansion strain in the deck near the abutment.

Material and Construction Optimization for Prevention of Premature Pavement Distress in PCC Pavements, Phase III Final Report, 2008

Mixture materials, mix design, and pavement construction are not isolated steps in the concrete paving process. Each affects the other in ways that determine overall pavement quality and long-term performance. However, equipment and procedures commonly used to test concrete materials and concrete pavements have not changed in decades, leaving gaps in our ability to understand and control the factors that determine concrete durability. The concrete paving community needs tests that will adequately characterize the materials, predict interactions, and monitor the properties of the concrete. The overall objectives of this study are (1) to evaluate conventional and new methods for testing concrete and concrete materials to prevent material and construction problems that could lead to premature concrete pavement distress and (2) to examine and refine a suite of tests that can accurately evaluate concrete pavement properties. The project included three phases. In Phase I, the research team contacted each of 16 participating states to gather information about concrete and concrete material tests. A preliminary suite of tests to ensure long-term pavement performance was developed. The tests were selected to provide useful and easy-to-interpret results that can be performed reasonably and routinely in terms of time, expertise, training, and cost. The tests examine concrete pavement properties in five focal areas critical to the long life and durability of concrete pavements: (1) workability, (2) strength development, (3) air system, (4) permeability, and (5) shrinkage. The tests were relevant at three stages in the concrete paving process: mix design, preconstruction verification, and construction quality control. In Phase II, the research team conducted field testing in each participating state to evaluate the preliminary suite of tests and demonstrate the testing technologies and procedures using local materials. A Mobile Concrete Research Lab was designed and equipped to facilitate the demonstrations. This report documents the results of the 16 state projects. Phase III refined and finalized lab and field tests based on state project test data. The results of the overall project are detailed herein. The final suite of tests is detailed in the accompanying testing guide.

Biomarkers for the assessment of chlorpyrifos effects on earthworms and on soil functional parameters

The objective of this work was to evaluate the effects of chlorpyrifos on earthworms and on soil functional parameters. An integrated laboratory-field study was performed in a wheat field in Argentina, sprayed with chlorpyrifos at two recommended application rates (240 or 960 g ha-1 style='vertical-align:baseline'> a.i.). Laboratory tests included neutral red retention time, comet assay (single cell gel electrophoresis), and avoidance behavior, each using the earthworm Eisenia andrei exposed in soil collected 1 or 14 days after pesticide application, and the bait-lamina test. Field tests assessed organic matter breakdown using the litterbag and bait-lamina assays. Earthworm populations in the field were assessed using formalin application and hand-sorting. The neutral red retention time and comet assays were sensitive biomarkers to the effects of chlorpyrifos on the earthworm E. andrei; however, the earthworm avoidance test was not sufficiently robust to assess these effects. Feeding activity of soil biota, assessed by the bait lamina test, was significantly inhibited by chlorpyrifos after 97 days, but recovered by the 118th day of the test. Litterbag test showed no significant differences in comparison to controls. Earthworm abundance in the field was too low to adequately test the sensitivity of this assessment endpoint.

Evaluation of Work Zone Speed Reduction Measures, 2000

The Iowa Department of Transportation (DOT) has made improving work zone (WZ) safety a high priority. Managing vehicle speeds through work zones is perceived to be an important factor in achieving this goal. A number of speed reduction techniques are currently used by transportation agencies throughout the country to control speeds and reduce speed variation at work zones. The purpose of this project is to study these and other applicable work zone speed reduction strategies. Furthermore, this research explores transportation agencies' policies regarding managing speeds in long-term, short-term, and moving work zones. This report consists of three chapters. The first chapter, a literature review, examines the current speed reduction practices at work zones and provides a review of the relevant literature. The speed control strategies reviewed in this chapter range from posting regulatory and advisory speed limit signs to using the latest radar technologies to reduce speeds at work zones. The second chapter includes a short write-up for each identified speed control technique. The write-up includes a description, the results of any field tests, the benefits and the costs of the technology or technique. To learn more about other state policies regarding work zone speed reduction and management, the Center for Transportation Research and Education conducted a survey. The survey consists of six multipart questions. The third chapter provides summaries of the response to each question.

Protection of Structural Concrete Substructures, Construction Report, HR-220, 1981

It is the objective of this project to determine, via field tests, the long term effectiveness of several available systems as their ability to protect concrete surfaces against the intrusion of chloride ions. Early concepts of this project included utilizing personnel from several offices within the Highway Division of the Iowa Department of Transportation. Cooperation and coordination with regularly scheduled activities were considered imperative. A meeting for this purpose was held on April 16, 1980. This meeting was attended by the investigators, Mr. Bernard C. Brown, Office of Materials, Mr. Richard Merritt, District 6 Materials Engineer, Mr. John Saunders, District 6 Maintenance Engineer, and Mr. James Phinney, Resident Maintenance Engineer.

Development and Evaluation of a Portable Device for Measuring Curling and Warping in Concrete Pavements, 2016

Portland cement concrete (PCC) pavement undergoes repeated environmental load-related deflection resulting from temperature and moisture variations across pavement depth. This has been recognized as resulting in PCC pavement curling and warping since the mid-1920s. Slab curvature can be further magnified under repeated traffic loads and may ultimately lead to fatigue failures, including top-down and bottom-up transverse, longitudinal, and corner cracking. It is therefore significant to measure the “true” degree of curling and warping in PCC pavements, not only for quality control (QC) and quality assurance (QA) purposes, but also for better understanding of its relationship to long-term pavement performance. Although several approaches and devices—including linear variable differential transducers (LVDTs), digital indicators, and some profilers—have been proposed for measuring curling and warping, their application in the field is subject to cost, inconvenience, and complexity of operation. This research therefore explores developing an economical and simple device for measuring curling and warping in concrete pavements with accuracy comparable to or better than existing methodologies. Technical requirements were identified to establish assessment criteria for development, and field tests were conducted to modify the device to further enhancement. The finalized device is about 12 inches in height and 18 pounds in weight, and its manufacturing cost is just $320. Detailed development procedures and evaluation results for the new curling and warping measuring device are presented and discussed, with a focus on achieving reliable curling and warping measurements in a cost effective manner.

Seismic Wave Velocity as a Means of In-Place Density Measurement, Part 1, HR-114

Velocity-density tests conducted in the laboratory involved small 4-inch diameter by 4.58-inch-long compacted soil cylinders made up of 3 differing soil types and for varying degrees of density and moisture content, the latter being varied well beyond optimum moisture values. Seventeen specimens were tested, 9 with velocity determinations made along two elements of the cylinder, 180 degrees apart, and 8 along three elements, 120 degrees apart. Seismic energy was developed by blows of a small tack hammer on a 5/8-inch diameter steel ball placed at the center of the top of the cylinder, with the detector placed successively at four points spaced 1/2-inch apart on the side of the specimen involving wave travel paths varying from 3.36 inches to 4.66 inches in length. Time intervals were measured using a model 217 micro-seismic timer in both laboratory and field measurements. Forty blows of the hammer were required for each velocity determination, which amounted to 80 blows on 9 laboratory specimens and 120 blows on the remaining 8 cylinders. Thirty-five field tests were made over the three selected soil types, all fine-grained, using a 2-foot seismic line with hammer-impact points at 6-inch intervals. The small tack hammer and 5/8-inch steel ball was, again, used to develop seismic wave energy. Generally, the densities obtained from the velocity measurements were lower than those measured in the conventional field testing. Conclusions were reached that: (1) the method does not appear to be usable for measurement of density of essentially fine-grained soils when the moisture content greatly exceeds the optimum for compaction, and (2) due to a gradual reduction in velocity upon aging, apparently because of gradual absorption of pore water into the expandable interlayer region of the clay, the seismic test should be conducted immediately after soil compaction to obtain a meaningful velocity value.

Aktiivinen melunvaimennus ampumaradalla

Aktiivinen melunvaimennus (active noise control, ANC) onkauan tunnettu ja sovellettu tekniikka. Kuitenkaan sitä ei ole aiemmin sovellettu impulssimaiseen satunnaiseen meluun. Tässä diplomityössä tutkitaan aktiivisenmelunvaimennuksen soveltuvuutta ampumaradan melunvaimennukseen. Ampumarata äärimmäisenä tapauksena asettaa korkean vaatimustason laitteistolle ja sen komponenteille. Suurin haaste on etsiä sopivat laitteiston komponentit, jotka tuottavat ja kestävät suurta äänenpainetasoa. Myös muuttuvat sääolosuhteet asettavat vaatimuksensa laitteiden mekaaniselle kestävyydelle sekä säänkestävyydelle. Työssä paneuduttiin erityisesti selvittämään, mitä kaupallisesti saatavilla olevia komponentteja voidaan hyödyntää aktiiviseen impulssimelunvaimennusjärjestelmään. Kaupallisten komponenttien soveltuvuutta aktiiviseen impulssimelunvaimennukseen analysoitiin laboratorio- ja kenttämittauksin. Työssä esitetään myös tulokset yksinkertaisella koelaitteistolla saavutetusta vaimennuksesta kenttäolosuhteissa.

Jätekeskuksen jasuljetun kaatopaikan jätevesien esikäsittelyn tehostamismahdollisudet

Tämän diplomityön tavoitteena oli tutkia toiminnassa olevan jätekeskuksen ja suljetun kaatopaikan jätevesien esikäsittelyn tehostamismahdollisuuksia. Tutkimuksessa pyrittiin löytämään niitä teknisiä keinoja, joilla jätevesien esikäsittelyä voidaan tehostaa erityisesti ammoniumtypen osalta. Tapausesimerkkinä työssä käytettiin Jätekukko Oy:n toiminnassa olevaa Kuopion jätekeskusta ja Kuopion kaupungin suljettua Silmäsuon kaatopaikkaa. Kohteiden jätevedet johdetaan kunnalliselle jätevedenpuhdistamolle, jossa jätevesien korkea ammoniumtyppipitoisuus ja matala lämpötila ovat häirinneet puhdistusprosessia. Tutkimuksen taustana selvitettiin jätekeskusten jakaatopaikkojen jätevesien käsittelyyn vaikuttavaa lainsäädäntöä, jätevesien ominaisuuksia ja niiden käsittelytekniikoita. Jätevesien käsittelyn nykytilaa Suomessa kartoitettiin jätehuoltoyhtiöille ja kunnille suunnatulla kyselyllä. Lisäksitutkimus perustui kenttäkokeisiin, joissa tutkittiin Kuopion jätekeskuksen nykyisen tasausaltaan toimivuutta vuoden ajan. Sekä Kuopion jätekeskuksen että Silmäsuon suljetun kaatopaikan jätevesistä otettiin vesien tarkkailuohjelmaan kuuluvien näytteiden lisäksi ylimääräisiä näytteitä, joilla pyrittiin saamaan uutta tietoa jäteveden laatumuuttujien vuodenaikaisvaihtelusta. Kuopion jätekeskuksen ja Silmäsuon suljetun kaatopaikan jätevesien käsittelyä tulevaisuudessa tarkasteltiin erilaisilla tilannemalleilla. Tutkimuksessa havaittiin, että Kuopion jätekeskuksen ja Silmäsuon suljetun kaatopaikan jätevedet olivat laadultaan ja määrältään erilaisia. Jätekeskuksen nykyinen jätevesien tasausallas poistaa ammoniumtyppeä vain kesäisin. Jätekeskuksen jätevesien nykyisen tasausaltaan toiminnan tehostaminen ei ole taloudellisesti perusteltua, vaan resurssit on kohdistettava uuden tasausaltaan rakentamiseen. Kuopion jätekeskuksen jätevesienesikäsittely ilman Silmäsuon suljetun kaatopaikan jätevesiä ei ole tarkoituksenmukaista, koska jätevedet johdetaan jätevedenpuhdistamolle samaa viemärilinjaa pitkin. Tällöin Silmäsuon suljetun kaatopaikan jätevedet tulevat mitätöimään jätekeskuksella tehdyn esikäsittelyn puhdistustuloksen Mahdollisen jätevesien yhteisen esikäsittelymenetelmän tulee olla fysikaalis-kemiallinen, jätevesien ominaisuuksista johtuen. Jos jätevesiä ei esikäsitellä yhdessä, jätekeskuksen jätevesien käsittelyksi riittävät uusi tasausallas ja siihen asennettava ilmastus. Tässä tapauksessa jätekeskuksen ympäristölupamääräysten ammoniumtyppipitoisuuden raja-arvoa on arvioitava uudelleen.

Cardiorespiratory and Cardiac Autonomic Responses to 30-15 Intermittent Fitness Test in Team Sport Players

Buchheit, M, Al Haddad, H, Millet GP, Lepretre, PM, Newton, M, and Ahmaidi, S. Cardiorespiratory and cardiac autonomic responses to 30-15 Intermittent Fitness Test in team sport players. J Strength Cond Res 23(1): xxx-xxx, 2009-The 30-15 Intermittent Fitness Test (30-15IFT) is an attractive alternative to classic continuous incremental field tests for defining a reference velocity for interval training prescription in team sport athletes. The aim of the present study was to compare cardiorespiratory and autonomic responses to 30-15IFT with those observed during a standard continuous test (CT). In 20 team sport players (20.9 +/- 2.2 years), cardiopulmonary parameters were measured during exercise and for 10 minutes after both tests. Final running velocity, peak lactate ([La]peak), and rating of perceived exertion (RPE) were also measured. Parasympathetic function was assessed during the postexercise recovery phase via heart rate (HR) recovery time constant (HRRtau) and HR variability (HRV) vagal-related indices. At exhaustion, no difference was observed in peak oxygen uptake (&OV0312;o2peak), respiratory exchange ratio, HR, or RPE between 30-15IFT and CT. In contrast, 30-15IFT led to significantly higher minute ventilation, [La]peak, and final velocity than CT (p < 0.05 for all parameters). All maximal cardiorespiratory variables observed during both tests were moderately to well correlated (e.g., r = 0.76, p = 0.001 for &OV0312;o2peak). Regarding ventilatory thresholds (VThs), all cardiorespiratory measurements were similar and well correlated between the 2 tests. Parasympathetic function was lower after 30-15IFT than after CT, as indicated by significantly longer HHRtau (81.9 +/- 18.2 vs. 60.5 +/- 19.5 for 30-15IFT and CT, respectively, p < 0.001) and lower HRV vagal-related indices (i.e., the root mean square of successive R-R intervals differences [rMSSD]: 4.1 +/- 2.4 and 7.0 +/- 4.9 milliseconds, p < 0.05). In conclusion, the 30-15IFT is accurate for assessing VThs and &OV0312;o2peak, but it alters postexercise parasympathetic function more than a continuous incremental protocol.

Improving Dynamic Characteristics of Open-loop Controlled Log Crane

The improvement of the dynamics of flexible manipulators like log cranes often requires advanced control methods. This thesis discusses the vibration problems in the cranes used in commercial forestry machines. Two control methods, adaptive filtering and semi-active damping, are presented. The adaptive filter uses a part of the lowest natural frequency of the crane as a filtering frequency. The payload estimation algorithm, filtering of control signal and algorithm for calculation of the lowest natural frequency of the crane are presented. The semi-active damping method is basedon pressure feedback. The pressure vibration, scaled with suitable gain, is added to the control signal of the valve of the lift cylinder to suppress vibrations. The adaptive filter cuts off high frequency impulses coming from the operatorand semi-active damping suppresses the crane?s oscillation, which is often caused by some external disturbance. In field tests performed on the crane, a correctly tuned (25 % tuning) adaptive filter reduced pressure vibration by 14-17 % and semi-active damping correspondingly by 21-43%. Applying of these methods require auxiliary transducers, installed in specific points in the crane, and electronically controlled directional control valves.

Courtship and mating behaviour of the Mediterranean corn borer, Sesamia nonagrioides (Lepidoptera: Noctuidae)

Se describe la secuencia de cortejo y apareamiento de machos y hembras de Sesamia nonagrioides (Lefèbvre) en el laboratorio. Esta secuencia no varió en presencia o ausencia de plantas de maíz. Se estudió la capacidad de atracción de un sexo sobre el otro atando el individuo de un sexo y dejando libre al complementario. La secuencia de cortejo y apareo de las hembras atadas fue la misma que la de las no atadas, pero los machos atados permanecieron absolutamente inactivos. La edad de los adultos (1 día versus 2 días) no afectó al porcentaje de apareamiento. Se encontraron diferencias en la hora del inicio de la llamada de las hembras y en la edad de las hembras en la primera llamada entre la población estudiada y lo descrito para una población griega, diferencias que podrían estar relacionadas con el origen geográfico. Se discute el papel de los penachos abdominales de los machos en el vuelo de cortejo, rechazándose que estimulen el comportamiento de llamada de las hembras o que las atraigan. Cuando no se aplicaron feromonas, el porcentaje de apareamiento en el laboratorio o en el campo no varió cuando aumentó la densidad de la población. Sin embargo, en los campos en que se aplicó confusión sexual, el porcentaje de apareamiento aumentó al aumentar la densidad de adultos. En la discusión se aportan algunas consecuencias para la investigación de la composición de las feromonas y su uso para el seguimiento de plagas y el control mediante confusión sexual.