Métodos de propagação do pinhão manso (Jatropha curcas L.)

Pós-graduação em Agronomia - FEIS

Adubação fosfatada no crescimento inicial e na nutrição de mudas de pinhão-manso

Physic nut (Jatropha curcas L.) is a perennial oilseed species that has aroused economic interest for biodiesel production. Among other factors, it is essential to determine the nutritional demands of this species to facilitate raising it as a crop. This study aimed to evaluate the early growth and mineral nutrition of physic nut, as well as soil fertility, as affected by phosphorus fertilization. The study was carried out in a plastic greenhouse in a completely randomized block experimental design with four replicates. The plants were grown in plastic pots filled with 50 dm³ of Latossolo Vermelho (Rhodic Hapludox). Application rates of 0, 50, 100, 150 and 200 mg dm-3 of P were tested, plus a control. Evaluations of plant height and root collar diameter were performed monthly. The experiment was ended 150 days after transplant of the seedlings, at which time leaf area, dry weight, leaf contents and total accumulation of macro- (N, P, K, Ca, Mg and S) and micronutrients (B, Cu, Fe, Mn and Zn) were performed, and soil chemical properties were analyzed. We concluded that absence of P fertilization alone is as limiting to early growth of physic nut as simultaneous absence of soil amendment and fertilization. The rate of 57 mg dm-3 of P may be recommended for initial growth of physic nut. The total accumulation of nutrients in physic nut seedlings exhibited the following order: K>N>Mg>Ca>P>S>Fe>Mn>B>Zn>Cu. Phosphorus fertilization resulted in increased soil cation exchange capacity (CEC).

Propagação do pinhão manso por estaquia, enxertia e sementes

Pós-graduação em Agronomia - FEIS

Avaliação de diferentes espaçamentos, altura e épocas de poda na cultura do pinhão manso na região de Selvíria-MS

Pós-graduação em Agronomia - FEIS

Preparação e caracterização do compósito poli (fluoreto de vinilideno) / polianilina com partículas de níquel

Pós-graduação em Ciência dos Materiais - FEIS

Estudo e análise do coeficiente de absorção acústico do compósito da fibra de cana

Pós-graduação em Engenharia Mecânica - FEIS

Implantação do pinhão-manso em solo degradado inoculado e acrescido de macrófita, cinza e hidrogel

Pós-graduação em Agronomia - FEIS

Processamento e caracterização de compósito fibra de sisal/resina epóxi via RTM

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização do compósito obtido a partir de borracha natural com negro e resíduos de couro aplicado como pisos e revestimentos

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Otimização dinâmica de rotores com eixos em compósito

Pós-graduação em Engenharia Mecânica - FEG

Síntese e caracterização do compósito SnO2/TiO2 nanoestruturado

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Eletrodos impressos descartáveis e de carbono vítreo modificados com grafeno e compósito de nanotubos de carbono-quitosana aplicados na determinação de corantes de cabelo

Pós-graduação em Química - IQ

Análise granulométrica do compósito cimentício produzido com adição de resíduos de madeira e escória

Since the early twenty-first century, the construction sector has been the second largest on the rise in the Brazilian industrial sector, with a growth of 1.4% in 2012, and is likely to remain at this level for a long time. However, unlike decades ago, the industry has been seeking in its manufacturing process, sustainable materials, encompassing in their works the concept of sustainability. Thus, the timber sector seeks to satisfy a market increasingly demanding, innovating techniques and utilization being less aggressive to the environment. The purpose of this study was to produce and evaluate the mechanical strength of the composite cement with the addition of wood residues and slag low oven. Therefore, it was made 42 specimen cement-slag-wood, carried out in two steps. Since at the first, it was varied only the slag particle size, and at the second, through the best result of the previous step, it was varied the wood particles granulometry. The mechanical performance of the composite was evaluated by the results obtained in the compression test and the physical test for determining the density of the material. In the first step of the process can be concluded that the best result was achieved with the use of slag particles retained on the 60 mesh sieve. In the second phase of the study concluded that the best results were achieved with wood particles with the large particles, i.e. particles retained on the 10 mesh sieve. Both in the first and in the second step it can be seen that there has been the influence of the particle size of the waste materials. With the obtained results, could be evaluated that the use of waste for the production of cement-slag-wood composite showed lower performance when compared to the results obtained in studies without the use of waste. However, some applications are feasible to be performed with the use of composite wood-cement-slag

Processamento do compósito de fibra de capim-sapê / epóxi e avaliação da resistência à flexão “t” de Student

In recent years a great worldwide interest has arisen for the development of new technologies that enable the use of products with less environmental impact. The replacement of synthetic fiber plants is a possibility very important because this fiber is renewable, biodegradable and few cost and cause less environmental impact. Given the above, this work proposes to develop polymeric composites of epoxy resin and study the behavior of these materials. Both, the epoxy resin used as matrix in the manufacture of sapegrass fiber composite, as tree composites formed by: epoxy/unidirectional sapegrass long fiber, 75% epoxy/25% short fiber, by volume, and 80% epoxy/20% short fiber, by volume, were characterized by bending, and the composites produced with short fibers random were inspected by Optical Microscopy and Acoustics Inspection (C-Scan). For the analysis of the sapegrass fiber morphology, composites 75% epoxy/25% short fiber (sheet chopped) and 80% epoxy/20% short fiber images were obtained by optical microscope and the adhesion between polymer/fiber was visualized. As results, the flexural strength of composites epoxy/unidirectional long fibers, 75% epoxy/25% short fiber and 80% epoxy/20% short fiber were 70.36 MPa, 21.26 MPa, 25.07 MPa, respectively. Being that composite showed that the best results was made up of long fibers, because it had a value of higher flexural strength than other composites analyzed

Produção e caracterização físico-mecânica do compósito cimento-madeira com variação granulométrica dos resíduos lignocelulósicos

The need to reduce environmental damage and add value to waste causes more and more new alternatives appear to unite these two points. One of the main ways to achieve this in timber industries and the use of waste for making panels. This work was aimed at studying the influence of particle size and density in Eucalyptus mechanical compressive strength of cement composite wood. For this study was performed production and physico-mechanical characterization of specimens, using portland cement, water and waste eucalyptus. The methodology consists of a statistical study of the results obtained by calculating the density and axial compression tests and a subsequent comparison of these results with other studies. The results showed that there are significant differences in density and compressive strength when using different particle sizes the particles of eucalyptus. In general, the smaller the particle size, the lower the compression strength and the greater the density when the samples are produced with the same trait