Preparation and magnetic properties of La–Mn and La–Co doped barium hexaferrites prepared via an improved co-precipitation/molten salt method

LaMn and LaCo doped barium hexaferrites of formula Ba(1-x)LaxFe(12-x)MxO19 (M=Mn, Co) (x=0.05 to 0.40) were prepared with an improved co-precipitation/molten salt method. For the synthesis, aqueous solutions of the appropriate metal chlorides were prepared in the ratio required except that the initial mole ratio of Fe and dopants to Ba was chosen to be 11:1, and then mixed with excess Na2CO3. The solutions were then cooled, filtered off, dried, then mixed with KCl flux, and heated at 450 degrees C and for 2 h. The temperature was then raised to 950 degrees C and kept for 4 h, then cooled. This new synthesis method, which employs a lower temperature and shorter reaction time, gives products with improved crystallinity and purity while the saturation magnetization and coercivity values are comparable with those synthesized via the high temperature method.

Reaction of (±)-1,1′-binaphthyl-2,2′-diyl hydrogen phosphate {(±)-phosH} with copper(II), cobalt(II) and iron(II) compounds; Identification by x-ray diffraction of [Co(CH3OH)4(H2O)2][(+)-phos][(−)-phos]. 2CH3OH·H2O

[Cu2(μO2CCH3)4(H2O)2], [CuCO3·Cu(OH)2], [CoSO4·7H2O], [Co((+)-tartrate)], and [FeSO4·7H2O] react with excess racemic (±)- 1,1′-binaphthyl-2,2′-diyl hydrogen phosphate {(±)-PhosH} to give mononuclear CuII, CoII and FeII products. The cobalt product, [Co(CH3OH)4(H2O)2]((+)-Phos)((−)-Phos) ·2CH3OH·H2O (7), has been identified by X-ray diffraction. The high-spin, octahedral CoII atom is ligated by four equatorial methanol molecules and two axial water molecules. A (+)- and a (−)-Phos− ion are associated with each molecule of the complex but are not coordinated to the metal centre. For the other CoII, CuII and FeII samples of similar formulation to (7) it is also thought that the Phos− ions are not bonded directly to the metal. When some of the CuII and CoII samples are heated under high vacuum there is evidence that the Phos− ions are coordinated directly to the metals in the products.

Metal cluster expansion by addition of low valent group 14 reagents: III. Reaction of bis[bis(trimethylsilyl)methyl]tin with M3(CO)12 or its derivatives (M = Fe, Ru, or Os): the crystal and molecular structures of M3(μ-SnR2)2(CO)10(R = CH(SiMe3)2; M = Ru or Os)

The stannylene [SnR2] (R = CH(SiMe3)2) reacts in different ways with the three dodecacarbonyls of the iron triad: [Fe3(CO)12] gives [Fe2(CO)8(μ-SnR2)], [Ru3(CO)12] gives the planar pentametallic cluster [Ru3(CO)10(μ-SnR2)2], for which a full structural analysis is reported, while [Os3(CO)12] fails to react. Different products are also obtained from three nitrile derivatives: [Fe3-(CO)11(MeCN)] gives [Fe2(CO)6(μ-SnR2)2], which has a structure significantly different from that of known Fe2Sn2 clusters, [Ru3(CO)10(MeCN)2] gives the pentametallic cluster described above, while [Os3(CO)10(MeCN)2] gives the isostructural osmium analogue, which shows the unusual feature of a CO group bridging two osmium atoms.

Effect of dextransucrase cellobiose acceptor products on the growth of human gut bacteria

The selective fermentation by human gut bacteria of gluco-oligosaccharides obtained from the reaction between the glucosyl group of sucrose and cellobiose, catalyzed by dextransucrases (DSR) from Leuconostoc mesenteroides, has been evaluated. Oligosaccharides were fractionated according to their molecular weight, and their effect on the growth of different bacterial groups was studied. To determine the structure (position and configuration of glycosidic linkages)�function relationship, their properties were compared to those of DSR maltose acceptor products (DSRMal) and of recognized prebiotic carbohydrates (fructo-oligosaccharides, FOS). Cellobiose acceptor products (DSRCel) showed bifidogenic properties similar to those of FOS. However, no significant differences related to molecular weight or isomeric configurations were found for DSRCel and DSRMal products.

Crystal design approaches for the synthesis of paracetamol co-crystals

Crystal engineering principles were used to design three new co-crystals of paracetamol. A variety of potential cocrystal formers were initially identified from a search of the Cambridge Structural Database for molecules with complementary hydrogen-bond forming functionalities. Subsequent screening by powder X-ray diffraction of the products of the reaction of this library of molecules with paracetamol led to the discovery of new binary crystalline phases of paracetamol with trans-1,4- diaminocyclohexane (1); trans-1,4-di(4-pyridyl)ethylene (2); and 1,2-bis(4-pyridyl)ethane (3). The co-crystals were characterized by IR spectroscopy, differential scanning calorimetry, and 1H NMR spectroscopy. Single crystal X-ray structure analysis reveals that in all three co-crystals the co-crystal formers (CCF) are hydrogen bonded to the paracetamol molecules through O−H···N interactions. In co-crystals (1) and (2) the CCFs are interleaved between the chains of paracetamol molecules, while in co-crystal (3) there is an additional N−H···N hydrogen bond between the two components. A hierarchy of hydrogen bond formation is observed in which the best donor in the system, the phenolic O−H group of paracetamol, is preferentially hydrogen bonded to the best acceptor, the basic nitrogen atom of the co-crystal former. The geometric aspects of the hydrogen bonds in co-crystals 1−3 are discussed in terms of their electrostatic and charge-transfer components.

Temperature-dependent reduction pathways of complexes fac-[Re(CO)3(N-R-imidazole)(1,10-phenanthroline)]+ (R = H, CH3)

Peculiar reduction pathways of the complexes fac-[Re(imH)(CO)3(phen)]+ and fac-[Re(imCH3)(CO)3(phen)]+ (imH = imidazole, imCH3 = N-methylimidazole and phen = 1,10-phenanthroline) have been unravelled by performing combined cyclic voltammetric and in situ IR spectroelectrochemical experiments. In the temperature range of 293–233 K, the initial reduction of the phen ligand in [Re(imH)(CO)3(phen)]+ results in irreversible conversion of the imidazole ligand to 3-imidazolate by a rapid phen•−→ imH intramolecular electron transfer coupled with N H bond cleavage. This process is followed by second phen-localized 1e− reduction producing [ReI(3-im−)(CO)3(phen•−)]−, similar to the analogous 2,2'-bipyridine complex. In contrast to the bpy analogue, the stability of the phen•−-containing complexes is significantly affected by lowering the temperature. At 233 K, a secondary reaction occurs in both [Re(3-im−)(CO)3(phen•−)]− and [Re(imCH3)(CO)3(phen•−)]. The resulting products exhibit v(CO) wavenumbers indistinguishable from those of the parent phen•− complexes; however, their oxidation occurs at a considerably more positive electrode potential. It is proposed that these species are produced by a new C C bond formation between the C(2) site of 3-im− or imCH3 and the C(2) site of the phen•−ligand.

Solvent-Dependent Formation of Os(0) Complexes by Electrochemical Reduction of [Os(CO)(2,2′-bipyridine)(L)Cl2]; L = Cl−,PrCN

Cyclic voltammetry and ultraviolet−visible/infrared (UV−vis/IR) spectroelectrochemistry were used to study the cathodic electrochemical behavior of the osmium complexes mer-[OsIII(CO) (bpy)Cl3] (bpy = 2,2′-bipyridine) and trans(Cl)-[OsII(CO) (PrCN)(bpy)Cl2] at variable temperature in different solvents (tetrahydrofuran (THF), butyronitrile (PrCN), acetonitrile (MeCN)) and electrolytes (Bu4NPF6, Bu4NCl). The precursors can be reduced to mer-[OsII(CO) (bpy•−)Cl3]2− and trans(Cl)-[OsII(CO)(PrCN) (bpy•−)Cl2]−, respectively, which react rapidly at room temperature, losing the chloride ligands and forming Os(0) species. mer-[OsIII(CO) (bpy)Cl3] is reduced in THF to give ultimately an Os−Os-bonded polymer, probably [Os0(CO) (THF)-(bpy)]n, whereas in PrCN the well-soluble, probably mononuclear [Os0(CO) (PrCN)(bpy)], species is formed. The same products were observed for the 2 electron reduction of trans(Cl)-[OsII(CO)(PrCN) (bpy)Cl2] in both solvents. In MeCN, similar to THF, the[Os0(CO) (MeCN)(bpy)]n polymer is produced. It is noteworthy that the bpy ligand in mononuclear [Os0(CO) (PrCN)(bpy)] is reduced to the corresponding radical anion at a significantly less negative potential than it is in polymeric [Os0(CO) (THF)(bpy)]n: ΔE1/2 = 0.67 V. Major differences also exist in the IR spectra of the Os(0) species: the polymer shows a broad ν(CO) band at much smaller wavenumbers compared to the soluble Os(0) monomer that exhibits a characteristic ν(Pr-CN) band below 2200 cm−1 in addition to the intense and narrow ν(CO) absorption band. For the first time, in this work the M0-bpy(M = Ru, Os) mono- and dicarbonyl species soluble in PrCN have been formulated as a mononuclear complex. Density functional theory (DFT) and time-dependent-DFT calculations confirm the Os(0) oxidation state and suggest that [Os0(CO)(PrCN)(bpy)] is a square planar moiety. The reversible bpy-based reduction of [Os0(CO) (PrCN)(bpy)] triggers catalytic reduction of CO2 to CO and HCOO−.

Spectroelectrochemical study of complexes [Mo(CO)2(h3-allyl)(adiimine)(NCS)] (a-diimine ¼ bis(2,6-dimethylphenyl)- acenaphthenequinonediimine and 2,20-bipyridine) exhibiting different molecular structure and redox reactivity

The redox properties and reactivity of [Mo(CO)2(η3-allyl)(α-diimine)(NCS)] (α-diimine = bis(2,6-dimethylphenyl)-acenaphthenequinonediimine (2,6-xylyl-BIAN) and 2,2′-bipyridine (bpy)) were studied using cyclic voltammetry and IR/UV–Vis spectroelectrochemistry. [Mo(CO)2(η3-allyl)(2,6-xylyl-BIAN)(NCS)] was shown by X-ray crystallography to have an asymmetric (B-type) conformation. The extended aromatic system of the strong π-acceptor 2,6-xylyl-BIAN ligand stabilises the primary 1e−-reduced radical anion, [Mo(CO)2(η3-allyl)(2,6-xylyl-BIAN•−)(NCS)]−, that can be reduced further to give the solvento anion [Mo(CO)2(η3-allyl)(2,6-xylyl-BIAN)(THF)]−. The initial reduction of [Mo(CO)2(η3-allyl)(bpy)(NCS)] in THF at ambient temperature results in the formation of [Mo(CO)2(η3-allyl)(bpy)]2 by reaction of the remaining parent complex with [Mo(CO)2(η3-allyl)(bpy)]− produced by dissociation of NCS− from [Mo(CO)2(η3-allyl)(bpy•−)(NCS)]−. Further reduction of the dimer [Mo(CO)2(η3-allyl)(bpy)]2 restores [Mo(CO)2(η3-allyl)(bpy)]−. In PrCN at 183 K, [Mo(CO)2(η3-allyl)(2,6-xylyl-BIAN•−)(NCS)]− converts slowly to 2e−-reduced [Mo(CO)2(η3-allyl)(2,6-xylyl-BIAN)(PrCN)]− and free NCS−. At room temperature, the reduction path in PrCN involves mainly the dimer [Mo(CO)2(η3-allyl)(bpy)]2; however, the detailed course of the reduction within the spectroelectrochemical cell is complicated and involves a mixture of several unassigned products. Finally, it has been shown that the five-coordinate anion [Mo(CO)2(η3-allyl)(bpy)]− promotes in THF reduction of CO2 to CO and formate via the formation of the intermediate [Mo(CO)2(η3-allyl)(bpy)(O2CH)] and its subsequent reduction.

Utilisation of by-products from sunflower-based biodiesel production processes for the production of fermentation feedstock

By-products streams from a sunflower-based biodiesel plant were utilised for the production of fermentation media that can be used for the production of polyhydroxyalkanoates (PHA). Sunflower meal was utilised as substrate for the production of crude enzyme consortia through solid state fermentation (SSF) with the fungal strain Aspergillus oryzae. Fermented solids were subsequently mixed with unprocessed sunflower meal aiming at the production of a nutrient-rich fermentation feedstock. The highest free amino nitrogen (FAN) and inorganic phosphorus concentrations achieved were 1.5 g L-1 and 246 mg L-1, respectively, when an initial proteolytic activity of 6.4 U mL-1 was used. The FANconcentrationwas increased to 2.3 g L-1 when the initial proteolytic activity was increased to 16 U mL-1. Sunflower meal hydrolysates were mixed with crude glycerol to provide fermentationmedia that were evaluated for the production of poly(3-hydroxybutyrateco- 3-hydroxyvalerate) (P(3HB-co-3HV)) using Cupriavidus necator DSM545. The P(3HB-co-3HV) (9.9 g l-1) produced contained 3HB and 3HV units with 97 and 3 mol %, respectively. Integrating PHA production in existing 1st generation biodiesel production plants through valorisation of by-product streams could improve their sustainability.

Characterization of O(2) ((1)Delta(g))-Derived Oxidation Products of Tryptophan: A Combination of Tandem Mass Spectrometry Analyses and Isotopic Labeling Studies

The fragmentation mechanisms of singlet oxygen [O(2) ((1)Delta(g))]-derived oxidation products of tryptophan (W) were analyzed using collision-induced dissociation coupled with (18)O-isotopic labeling experiments and accurate mass measurements. The five identified oxidized products, namely two isomeric alcohols (trans and cis WOH), two isomeric hydroperoxides (trans and cis WOOH), and N-formylkynurenine (FMK), were shown to share some common fragment ions and losses of small neutral molecules. Conversely, each oxidation product has its own fragmentation mechanism and intermediates, which were confirmed by (18)O-labeling studies. Isomeric WOH lost mainly H(2)O + CO, while WOOH showed preferential elimination of C(2)H(5)NO(3) by two distinct mechanisms. Differences in the spatial arrangement of the two isomeric WOHs led to differences in the intensities of the fragment ions. The same behavior was also found for trans and cis WOOH. FMK was shown to dissociate by a diverse range of mechanisms, with the loss of ammonia the most favored route. MS/MS analyses, (18)O-labeling, and H(2)(18)O experiments demonstrated the ability of FMK to exchange its oxygen atoms with water. Moreover, this approach also revealed that the carbonyl group has more pronounced oxygen exchange ability compared with the formyl group. The understanding of fragmentation mechanisms involved in O(2) ((1)Delta(g))-mediated oxidation of W provides a useful step toward the structural characterization of oxidized peptides and proteins. (J Am Soc Mass Spectrom 2009, 20, 188-197) (C) 2009 Published by Elsevier Inc. on behalf of American Society for Mass Spectrometry

Tailored Media for Homogeneous Cellulose Chemistry: Ionic Liquid/Co-Solvent Mixtures

Co-solvents can minimize two of the major problems associated with the use of ionic liquids (ILs) as solvents for homogeneous derivatization of cellulose: high viscosity and limited miscibility with non-polar reagents or reaction products. Thus, the effects of 18 solvents and 3 binary solvent mixtures on cellulose solutions in three ILs were systematically studied with respect to the solution phase behavior. The applicable limits of these mixtures were evaluated and general guidelines for the use of co-solvents in cellulose chemistry could be advanced: Appropriate co-solvents should have EN T values (normalized empirical polarity) > 0.3, very low ``acidity`` (alpha < 0.5), and relatively high ""basicity`` (beta >= 0.4). Moreover, novel promising co-solvents and binary co-solvent mixtures were identified.

Using GIS Network Analyst to Identify Suppliers for a Produce Co-op in Waterville, ME

The idea for organizing a cooperative market on Waterville Main Street was proposed by Aime Schwartz in the fall of 2008. The Co-op would entail an open market located on Main Street to provide fresh, local produce and crafts to town locals. Through shorter delivery distances and agreements with local farmers, the co-op theoretically will offer consumers lower prices on produce than can be found in conventional grocery stores, as well as an opportunity to support local agriculture. One of the tasks involved with organizing the Co-op is to source all of the produce from among the hundreds of farmers located in Maine. The purpose of this project is to show how Geographic Information System (GIS) tools can be used to help the Co-op and other businesses a) site nearby farms that carry desired produce and products, and b) determine which farms are closest to the business site. Using GIS for this purpose will make it easier and more efficient to source produce suppliers, and reduce the workload on business planners. GIS Network Analyst is a tool that provides network-based spatial analysis, and can be used in conjunction with traditional GIS technologies to determine not only the geometric distance between points, but also distance over existing networks (like roads). We used Network Analyst to find the closest produce suppliers to the Co-op for specific produce items, and compute how far they are over existing roads. This will enable business planners to source potential suppliers by distance before contacting individual farmers, allowing for more efficient use of their time and a faster planning process.

Combining Satellite And Gauge Precipitation Data With Co-Kriging Method For Jakarta Region

Jakarta is vulnerable to flooding mainly caused by prolonged and heavy rainfall and thus a robust hydrological modeling is called for. A good quality of spatial precipitation data is therefore desired so that a good hydrological model could be achieved. Two types of rainfall sources are available: satellite and gauge station observations. At-site rainfall is considered to be a reliable and accurate source of rainfall. However, the limited number of stations makes the spatial interpolation not very much appealing. On the other hand, the gridded rainfall nowadays has high spatial resolution and improved accuracy, but still, relatively less accurate than its counterpart. To achieve a better precipitation data set, the study proposes cokriging method, a blending algorithm, to yield the blended satellite-gauge gridded rainfall at approximately 10-km resolution. The Global Satellite Mapping of Precipitation (GSMaP, 0.1⁰×0.1⁰) and daily rainfall observations from gauge stations are used. The blended product is compared with satellite data by cross-validation method. The newly-yield blended product is then utilized to re-calibrate the hydrological model. Several scenarios are simulated by the hydrological models calibrated by gauge observations alone and blended product. The performance of two calibrated hydrological models is then assessed and compared based on simulated and observed runoff.

Co-evolução dos componentes do marco institucional e das trajetórias de acumulação de capacidades tecnológicas no setor de agro-energia (etanol) no Brasil (1970-2009)

Esta dissertação centra-se no exame da evolução dos componentes do marco institucional em associação com as trajetórias de acumulação de capacidades tecnológicas de produção e inovação em setores à base de recursos naturais em economias emergentes. Esse relacionamento é examinado no setor de etanol brasileiro, no período entre 1970 e 2009. O marco institucional é operacionalizado à base das macro-instituições (os regimes complexos constituídos por políticas públicas), meso-instituições (as relações políticas e estruturas burocráticas) e as instituições baseadas em conhecimento (os institutos de pesquisa e as universidades). As trajetórias de acumulação de capacidades tecnológicas são examinadas à base de níveis de inovação. A dissertação baseia-se em um estudo de caso em nível setorial. Além disso, o estudo baseia-se em evidências obtidas a partir de fontes diversas, em nível de indústria, em documentos governamentais e também em evidências secundárias em nível de empresa. Os principais resultados desta dissertação são os seguintes: (1) O setor de etanol atingiu níveis inovadores de capacidade tecnológica nas duas funções analisadas. Numa escala de 1 a 5, o setor adquiriu, durante o 1º período (1970-1989), capacidades tecnológicas industriais (produto e processo) no Nível 3 e, durante o 2º período (1990-2009), o setor de etanol acumulou capacidades tecnológicas industriais no Nível 5. No tocante à acumulação de capacidades tecnológicas na área agrícola (matéria-prima), durante o 1º período, o setor adquiriu capacidades tecnológicas no Nível 4 e apenas no período seguinte atingiu o Nível 5. (2) As instituições desempenharam um papel relevante sobre as trajetórias de acumulação de capacidades tecnológicas no setor de etanol brasileiro. Entre elas destaca-se às atividades de P&D desenvolvidas em instituições baseadas em conhecimento, que acumularam capacidades tecnológicas de produção e inovação, compartilhadas com as empresas. (3) Entretanto, o estudo aponta para algumas vulnerabilidades do setor de etanol brasileiro no que se refere a sua capacidade de sustentar o seu desempenho inovador. Entre elas destaca-se: (1) grande parte das atividades inovadoras em nível de P&D é realizada a base de arranjos externos, com pouco esforço de atividades realizadas a partir das empresas; (2) apesar do enorme esforço governamental para desenvolver o setor, esse está direcionado (locked-in) à trajetória de acumulação de capacidades tecnológicas de etanol de 1ª geração; (3) os componentes do marco institucional incentivaram as atividades de pesquisa em universidades e institutos de pesquisa, em nível de bancada, que resultaram em invenções e projetos experimentais; (4) as condições favoráveis de mercado, a grande disponibilidade de cana-de-açúcar e a flexibilidade de produção de etanol/álcool contribuíram para a acomodação do setor de etanol, ou seja, parece haver uma zona de conforto no setor. Desta forma, as evidências alertam sobre a necessidade de investimentos em atividades inovadoras de P&D dentro das empresas (foco em inovações, riqueza e na diversificação para outros setores). Portanto, os resultados desta dissertação permitem apontar sugestões para gestores governamentais. As novas políticas públicas podem: (1) redirecionar as estratégias de acumulação de capacidades tecnológicas inovadoras, fortemente focadas na sustentação das trajetórias de acumulação de capacidades tecnológicas para produzir etanol de 1ª geração; (2) impulsionar a acumulação de capacidades tecnológicas de produção e inovação na trajetória emergente para produzir etanol de 2ª geração, atualmente em nível experimental e largamente desenvolvida dentro das instituições baseadas em conhecimento, e para diversificar os produtos para novos setores e linhas de negócio. Os resultados desta dissertação também sugerem aos gestores de empresas no setor brasileiro de etanol: (1) reformular as estratégias empresariais com a finalidade de expandir as atividades inovadoras dentro das empresas do setor de etanol, que poderão resultar na criação de inovações em escala industrial; (2) as empresas do setor de etanol deveriam assumir um comportamento proativo com a finalidade de coordenar os esforços de P&D em direção aos problemas e desafios futuros a serem enfrentados pelo setor brasileiro de etanol.

Adsorção dos gases NH3, NO e H2S em fosfato de vanadila, hidrogeno fosfato de vanadila e fosfatos de vanadila dopados por Al, Co, Mn e Cr

In this work were synthesized the materials called vanadyl phosphate, hydrogen vanadyl phosphate and vanadyl phosphate doped by transition metals with the aim in adsorption the following compounds: ammonia, hydrogen sulfide and nitrogen oxide. To characterize the starting compounds was used DRX, FTIR, FRX and TG analysis. After the characterization of substrates, proceeded de adsorption of NH3 and H2S gases in reactor, passing the gases with continuous flow for 30 min and room temperature. Gravimetric data indicate that the matrices of higher performance in adsorption of ammonia was those doped by aluminum and manganese, obtaining results of 216,77 mgNH3/g and 200,40 mgNH3/g of matrix, respectively. The matrice of higher performance in adsorption of hydrogen sulfide was that doped by manganese, obtaining results of 86,94 mgH2S/g of matrix. The synthesis of substrates VOPO4.2H2O and MnVOPO4.2H2O with nitrogen oxide was made in solution, aiming the final products VOPO4.G.nH2O and MnVOPO4.G.nH2O (G = NO and n = number of water molecules). The thermo analytical behavior and the infrared spectroscopy are indicative of formation of VOPO4.2,5NO.3H2O compound. Results of scanning electron microscopy (SEM) and Energy dispersive spectroscopy (EDS) of materials vanadyl phosphate and vanadyl phosphate modified after reaction in solid state or in solution with the gases show morphology changes in substrates, beyond the formation of orthorhombic sulfur crystals over their respective hosts when these adsorb hydrogen sulfide