Er_xY_(1-x)AlO_3晶体的荧光动力学研究

本文详细计算了辐射跃迁几率、无辐射跃迁几率、交叉弛豫几率和其他光谱参数。并且在考虑上述三种辐射过程的情况下,讨论了Er~(3+)离子的荧光动力学过程,研究了荧光发射特征与Er~(3+)离子浓度的关系,给出了它们的规律。

RE_(1-x)B_xF_(3-y)(RE=Y、La、Ce、Gd;B=Ca、Ba)的敏感性质的研究

LaF_3作为离子选择性电极和对气体的敏感性质已进行了一定的研究,但其他稀土氟化物的敏感性质却未见报道。本文合成了RE_(1-x)B_xF_(3-y),研究了它们的结构、电学性质及敏感性质,得到有可能在150℃使用的固体电解质氧敏材料。 (一) RE_(1-x)B_xF_(3-y)的结构分析 结构分析表明,Ca、Ba置换RE的含量少时,如La_(0.95)Ba_(0.05)F_(3-y)、Ce_(0.95)Ca_(0.05)F_(3-y)的X射线衍射分析结果与LaF_3、CeF_3相似,说明它们是固溶体。而Ca置换RE含量较多时,如Y_(0.71)Ca_(0.29)F_(3-y)、Gd_(0.85)Ca_(0.15)F_(3-主)的X射线衍射分析结果却与相应的YF_3和GdF_3完全不

Y_(1-x)Ca_xBa_2Cu_3O_(7-y)超导材料的研究

研究了Y_(1-x)Ca_xBa_2Cu_3O_(7-y)系超导材料,当x≤0.15时,钙离子部分置换了123相中钇离子而形成固溶体,导致正交相晶胞参数稍微增大。钙含量增加,三价铜的含量上升,T_c却下降。由于钙离子取代钇离子后主要影响邻近的Cu(2)-O层的性质,这说明Cu(2)-O层的性质对超导电性起了很重要的作用。

多晶富镉Hg_(1-x)Cd_xTe的电沉积及Hg_(0.09)Cd_(0.91)Te薄膜的光电化学行为

本文研究了在酸性CdSO_4+HTeO_2~+6HgCl_2 电解液中多晶富镉Hg_(1-x),Cd_(?),Te(x>0.5)的电沉积过程,实现了三种离子在同一电位下共沉积的技术。对在钛基底上沉积出的薄膜进行XRD,SEM和EDAX分析,结果表明薄膜为闪锌矿型的多晶结构,分布均匀连续。考察了(1—x)=0.09时多晶薄膜在多硫氧化还原电对液中的光电化学行为,光强为100mW/cm~2时,短路光电流I_(sc)=1.88mA/cm~2,开路光电压V_(oc)=0.25V,填充因子F·F=0.22。由光电化学光谱所确定出的禁带宽度E_g=1.26eV,Mott-schottky曲线给出了电极的平带电位φfb为—1.26V(vs.SCE),从而得到开路光电压V_(oc)可能达到的最大值为0.49V。因此,多晶富镉Hg_(1-x)Cd_xTe薄膜是一种很有潜力的光活性电极材料。

Sm_xLa_(1-x)P_5O_(14)和Dy_xY_(1-x)P_5O_(14)晶体的荧光寿命研究

本文用脉冲衰减法和时间分辨荧光光谱法测量了六种不同稀土离子浓度的Sm_xLa_(1-x)P_5O_4晶体的~4G_(5/2)→~6H_J(J=5/2,7/2,9/2,11/2)四个能级和七种不同稀土离子浓度的Dy_xY_(1-x)P_5O_(14)晶体的~4F_(9/2)→~6H_J(J=15/2,13/2,11/2,9/2)四个能级的荧光寿命和荧光强度。结果指出,在这类晶体中,Sm~(3+)和Dy~(3+)的荧光寿命随着离子的浓度增加而变短,存在着严重的荧光浓度猝灭现象。最后还讨论了浓度与寿命,寿命与荧光强度的关系。

Ln_xYb_(1-x)Ba_2Cu_3O_(7-δ)(Ln=La 或 Nd)的结构和超导电性的研究

本文系统地研究了轻稀土元素 La、Nd 等部分取代 YbBa_2Cu_3O(7-δ)化合物中的 Yb 对结构和超导电性所产生的影响。少量(约0.1摩尔比)轻稀土元素可有效抑制 YbBa_2Cu_3O(7-δ)化合物中杂相的生成,提高体系中 Cu~(3+)/Cu~(2+)之值。

Estudio del vitrocerámico (1-x) Li2B4O7-xBi2WO6 (0 > x < 0.35) usando el método Rietveld

[Tesis] ( Maestría en Ciencias con Orientación en Ingeniería Cerámica) U.A.N.L.

Crystal growth and magnetic properties of tin selenide-doped europium Sn(1-x)Eu(x)Se

The growth and magnetic properties of Tin Selenide (SnSe) doped with Eu(2+) Sn(1-x)Eu(x)Se (x=2.5%) were investigated. Q-band (34 GHz) electron paramagnetic resonance measurements show that the site symmetry of Eu(2+) at 4.2 K is orthorhombic and the Lande factor was determined to be g=1.99 +/- 0.01. The exchange coupling between nearest-neighbor (NN) Eu(2+) ions was estimated from magnetization and magnetic-susceptibility measurements using a model that takes into account the magnetic contributions of single ions, pairs and triplets. The exchange interaction between Eu(2+) nearest neighbors was found to be antiferromagnetic with an estimated average value of J(p)/k(B) =-0.18 +/- 0.03 K. (C) 2009 Elsevier B.V. All rights reserved.

CO preferential oxidation (CO-PROx) on La(1-x)Ce(x)NiO(3) perovskites

La(1-x)Ce(x)NiO(3) perovskites have been prepared, characterized by XRD. TPR and surface area and tested as catalysts for CO-PROx, with a feed of 2.5% CO, 5% O(2), 33% H(2) and N(2) to 100%. The samples exhibited an XRD pattern typical of the perovskite, with traces of NiO in the LaNiO(3) and La(0.95)Ce(0.05)NiO(3) samples, with some La(2)NiO(4) in the La(0.90)Ce(0.10)NiO(3) sample. All samples were active, but the perovskites with cerium showed good catalytic activity, demonstrating the promoter effect of cerium. The highest conversion of CO and H(2) was obtained with La(0.95)Ce(0.05)NiO(3), probably due to a synergy between Ni and Ce that enhanced O(2) mobility. (c) 2010 Elsevier B.V. All rights reserved.

Study of Water-Gas-Shift Reaction over La((1-y))Sr(y)Ni(x)Co((1-x))O(3) Perovskite as Precursors

The performance of La((1-y))Sr(y)Ni(x)Co((1-x))O(3) perovskites for the water gas shift reaction (WGSR) was investigated. The samples were prepared by the co- precipitation method and were performed by the BET method, XRD, TPR, and XPS. The catalytic tests were performed at 300 and 400 A degrees C and H(2)O(v)/CO = 2.3/1 (molar ratio). The sample with the highest surface area is La(0.70)Sr(0.30)NiO(3). The XRD results showed the formation of perovskite structure for all samples, and the La(0.70)Sr(0.30)NiO(3) sample also presented peaks corresponding to La(2)NiO(4) and NiO, indicating that the solubility limit of Sr in the perovskite lattice was surpassed. The replacement of Co by Ni favored the reduction of the species at lower temperatures, and the sample containing Sr presented the highest amount of reducible species, as identified by TPR results. All samples were active, the Sr containing perovskite appearing the most active due to the highest surface area, presence of the La(2)NiO(4) phase, and higher content of Cu in the surface, as detected by XPS. Among the samples containing Co, the most active one was that with x = 0.70 (60% of CO conversion).

Leakage current, ferroelectric and structural properties in Pb(1-x)Ba(x)TiO(3) thin films prepared by chemical route

Single-phase perovskite structure Pb(1-x)Ba(x)TiO(3) thin films (x = 0.30, 0.50 and 0.70) were deposited on Pt/Ti/SiO(2)/Si substrates by the spin-coating technique. The dielectric study reveals that the thin films undergo a diffuse type ferroelectric phase transition, which shows a broad peak. An increase of the diffusivity degree with the increasing Barium contents was observed, and it was associated to a grain decrease in the studied composition range. The temperature dependence of the phonon frequencies was used to characterize the phase transition temperatures. Raman modes persist above tetragonal to cubic phase transition temperature, although all optical modes should be Raman inactive. The origin of these modes was interpreted in terms of breakdown of the local cubic symmetry by chemical disorder. The absence of a well-defined transition temperature and the presence of broad bands in some interval temperature above FE-PE phase transition temperature Suggested a diffuse type phase transition. This result corroborates the dielectric constant versus temperature data, which showed a broad ferroelectric phase transition in these thin films. The leakage Current density of the PBT thin films was studied at different temperatures and the data follow the Schottky emission model. Through this analysis the Schottky barrier height values 0.75, 0.53 and 0.34 eV were obtained to the PBT70, PBT50 and PBT30 thin films, respectively. (C) 2008 Elsevier Ltd. All rights reserved.

Effect of the catalyst composition in the Pt-x(Ru-Ir)(1-x)/C system on the electro-oxidation of methanol in acid media

The effect of variations in the composition for ternary catalysts of the type Pt-x(Ru-Ir)(1-x)/C on the methanol oxidation reaction in acid media for x values of 0.25, 0.50 and 0.75 is reported. The catalysts were prepared by the sol-gel method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), atomic absorption spectroscopy (AAS) and energy dispersive X-ray (EDX) analyses. The nanometric character (2.8-3.2 nm) of the sol-gel deposits was demonstrated by XRD and TEM while EDX and AAS analyses showed that the metallic ratio in the compounds was very near to the expected one. Cyclic voltammograms for methanol oxidation revealed that the reaction onset occur at less positive potentials in all the ternary catalysts tested here when compared to a Pt-0.75-Ru-0.25/C (E-Tek) commercial composite. Steady-state polarization experiments (Tafel plots) showed that the Pt-0.25(Ru-Ir)(0.75)/C catalyst is the more active one for methanol oxidation as revealed by the shift of the reaction onset towards lower potentials. In addition, constant potential electrolyses suggest that the addition of Ru and Ir to Pt decreases the poisoning effect of the strongly adsorbed species generated during methanol oxidation. Consequently, the Pt-0.25 (Ru-Ir)(0.75)/C Composite catalyst is a very promising one for practical applications. (c) 2007 Elsevier B.V. All rights reserved.

Study on LiFe1 − xSm xPO4/C used as cathode materials for lithium-ion batteries with low Sm component

LiFe1 − xSmxPO4/C cathode materials were synthesized though a facile hydrothermal method. Compared with high-temperature solid-phase sintering, the method can allow for the fabrication of low Sm content (2 %), a scarce and expensive rare earth element, while the presence of an optimized carbon coating with large amount of sp²-type carbon sharply increases the material’s electrochemical performance. The high-rate dischargeability at 5 C, as well as the exchange current density, can be increased by 21 and 86 %, respectively, which were attributed to the fine size and the large cell parameter a/c as much. It should be pointed out that the a/c value will be increased for the LiFePO4 Sm-doped papered by both of the two methods, while the mechanism is different: The value c is increased for the front and the value a is decreased for the latter, respectively.

The optical absorption edge of nanocrystalline Ga(1-x)Mn(x)N films deposited by reactive sputtering

We have focused on the optical absorption edge of nanocrystalline Ga(1-x)Mn(x)N (0.00 <= x <= 0.18) films deposited by reactive RF magnetron sputtering. The films obtained are nanocrystalline with grain sizes of about 25 nm, having wurtzite structure and strong orientation texture in the c-axis direction. The optical characterizations of the absorption edges were obtained in the 190-2600 nm spectral range. The increase of the Mn content causes an increase of the absorption coefficient which can be clearly noticed at low energies, and a quasi-linear decrease of the optical gap. Broad absorption bands observed around similar to 1.3 and similar to 2.2 eV were associated with transitions between the Mn acceptor level and the valence and conduction bands, respectively. The observed changes in the optical properties due to the Mn incorporation observed in these nanocrystalline films are similar to those reported for ferromagnetic GaMnN single-crystal films.

Síntese e caracterização de pós Ba(x)Sr(1-x)Co0,8Fe0,2O3- através do método de coprecipitação via oxalato

Ceramic powders based on oxides of perovskite-type structure is of fundamental interest nowadays, since they have important ionic-electronic conductivity in the use of materials with technological applications such as gas sensors, oxygen permeation membranes, catalysts and electrolytes for solid oxide fuel cells (SOFC). The main objective of the project is to develop nanostructured ceramic compounds quaternary-based oxide Barium (Br), Strontium (Sr), Cobalt (Co) and Iron (Fe). In this project were synthesized compounds BaxSr(1-x)Co0, 8Fe0,2O3- (x = 0.2, 0.5 and 0.8) through the oxalate co-precipitation method. The synthesized powders were characterized by thermogravimetric analysis and differential thermal analysis (TGADTA), X-ray diffraction (XRD) with the Rietveld refinement using the software MAUD and scanning electron microscopy (SEM). The results showed that the synthesis technique used was suitable for production of nanostructured ceramic solid solutions. The powders obtained had a crystalline phase with perovskite-type structure. The TGA-DTA results showed that the homogeneous phase of interest was obtained temperature above 1034°C. It was also observed that the heating rate of the calcination process did not affect the elimination of impurities present in the ceramic powder. The variation in the addition of barium dopant promoted changes in the average crystallite size in the nanometer range, the composition being BSCF(5582) obtained the lowest value (179.0nm). The results obtained by oxalate co-precipitation method were compared with those synthesis methods in solid state and EDTA-citrate method