Thermo and photoluminescence properties of Eu3+ activated hexagonal, monoclinic and cubic gadolinium oxide nanorods

Different phases of Eu3+ activated gadolinium oxide (Gd (OH)(3), GdOOH and Gd2O3) nanorods have been prepared by the hydrothermal method with and without cityl trimethyl ammonium bromide (GAB) surfactant. Cubic Gd2O3:Eu (8 mol%) red phosphor has been prepared by the dehydration of corresponding hydroxide Gd(OH)(3):Eu after calcinations at 350 and 600 degrees C for 3 h, respectively. When Eu3+ ions were introduced into Gd(OH)(3), lattice sites which replace the original Gd3+ ions, a strong red emission centered at 613 nm has been observed upon UV illumination, due to the intrinsic Eu3+ transition between D-5(0) and F-7 configurations. Thermoluminescence glow curves of Gd (OH)(3): Eu and Gd2O3:Eu phosphors have been recorded by irradiating with gamma source ((CO)-C-60) in the dose range 10-60 Gy at a heating rate of 6.7 degrees C sec(-1). Well resolved glow peaks in the range 42-45, 67-76,95-103 and 102-125 degrees C were observed. When gamma-irradiation dose increased to 40 Gy, the glow peaks were reduced and with increase in gamma-dose (50 and 60 Gy) results the shift in first two glow peak temperatures at about 20 degrees C and a new shouldered peak at 86 degrees C was observed. It is observed that there is a shift in glow peak temperatures and variation in intensity, which is mainly attributed to different phases of gadolinium oxide. The trapping parameters namely activation energy (E), order of kinetics (b) and frequency factor were calculated using peak shape and the results are discussed. (C) 2010 Elsevier B.V. All rights reserved.

Orientational disorder and other aspects of C70 and C60-C70 films deposited on single-crystal substrates

C-70 films deposited on highly oriented pyrolytic graphite (HOPG), Ag(110), Ag(111) and Pt(110) substrates have been investigated by scanning tunnelling microscopy. Interesting observations on novel molecular arrangements, as well as orientational disorder, are presented. Solid solutions of C-60 and C-70 show interesting packing of these molecules when deposited on HOPG.

Polymerization and Pressure-Induced Amorphization of C60 and C70

Scanning tunneling microscopy of solid films of C-60 and C-70 clearly demonstrate the occurrence of photochemical polymerization of these fullerenes in the solid state. X-ray diffraction studies show that such a polymerization is accompanied by contraction of the unit-cell volume in the case of C-60 and expansion in the case of C-70. This is also evidenced from the STM images. These observations help to understand the differences in the amorphization behavior of C-60 and C-70 under pressure. Amorphization of C-60 under pressure is irreversible because it is accompanied by polymerization associated with a contraction of the unit cell volume. Monte Carlo simulations show how pressure-induced polymerization is favored in C-60 because of proper orientation as well as the required proximity of the molecules. Amorphization of C-70, on the other hand, is reversible because C-70 is less compressible and polymerization is not favored under pressure.

Raman Spectroscopy of the Charge Transfer Complex (TTF)x C60 Br8

We report Raman studies on powder samples of the charge transfer complex (TTF)(x)C60Br8 at room temperature. The phonons show considerable softening with respect to the frequencies observed in the Raman spectrum of solid C60Br8. The strongest mode at 1464 cm(-1) in C60Br8 is red shifted to a doublet with peaks at 1414 and 1421 cm(-1), implying an average phonon softening Delta omega of -47 cm(-1). A comparison with the phonon softening of the corresponding A(g)(2) mode in alkali-doped C-60 (Delta omega similar to -36 cm(-1) for A(6)C(60), A = K, Rb or Cs) suggests that 8 electrons are transferred per C60Br8 molecule in the charge transfer complex. The mode at 503 cm(-1) in C60Br8 is shifted upwards, similar to that in A(6)C(60) compounds.

Hybrid systems through natural product leads: An approach towards new molecular entities

Hybrid systems are constructs of different molecular entities, natural or unnatural, to generate functional molecules in which the characteristics of various components are modulated, amplified or give rise to entirely new properties. These hybrids can be designed from carefully selected components either through domain intergration of key structural/functional features or via straightforward covalent linkages. Some of the recently reported hybrid systems based on steroid, carbohydrate, C-60-fullerene platforms, amongst others, mainly crafted with the object of enhancement of the therapeutical spectrum, will be discussed.

Temperature dependence of infrared and Raman modes in polymeric RbC60

Temperature dependence of the intra-molecular vibrational modes Of C-60 in the quasi-1D polymeric RbC60, across the low temperature transition at similar to50 K, has been probed through infrared (IR) and Raman spectroscopies. With the lowering of temperature, the split IR modes of RbC60 are seen to harden but below 50 K a small but definitive signature of an anomalous softening is observed. In addition, the background IR transmission shows an increase below 50 K with the opening of a well defined gap in the electronic spectrum. The implications of these results, along with those of Raman measurements, are discussed in terms of the interaction of intra-molecular phonons with electrons and spin excitations in the system. (C) 2002 Published by Elsevier Science Ltd.

Synthesis and Self-Assembly of Donor-Acceptor-Donor Based Oligothiophenes and Their Optoelectronic Properties

In this work, the synthesis of an oligothiophene having a donor acceptor donor (D-A-D) chromophore with hydrogen bonding groups is described. The D-A-D molecule was demonstrated to self-organize via intermolecular H-bonding between barbituric acid units. Interactions between the oligothiophene subunits were also found to be important, affording nanoribbons that could be observed by atomic force and transmission electron microscopy. The applicability of the oligothiophene for organic electronic applications was investigated by fabricating organic field-effect transistors (OFETs) and organic photovoltaic devices. The OFET measurements yielded p-type mobility of 7 x 10(-7) cm(2)/(Vs), and when blended with C(60)-PCBM, the photovoltaic efficiency was observed to be 0.18%.

Pillar height dependent formation of unprecedented Pd-8 molecular swing and Pd-6 molecular boat via multicomponent self-assembly

Three-component self-assembly of a cis-blocked 90 degrees Pd(II) acceptor with a mixture of a tetraimidazole and a linear dipyridyl donor self-discriminated into unusual Pd-8 molecular swing (1) and Pd-6 molecular boat (2), which are characterized by single-crystal X-ray diffraction analysis; their ability to bind C-60 in solution is established by fluorescence titration.

Composites of Graphene and Other Nanocarbons with Organogelators Assembled through Supramolecular Interactions

Carbon nanomaterials (CNMs), such as exfoliated graphene (EG), long-chain functionalized EG, single-walled carbon nanotubes (SWNTs), and fullerene (C-60), have been investigated for their interaction with two structurally different gelators based on all-trans tri-p-phenylenevinylene bis-aldoxime (1) and n-lauroyl-L-alanine (2) both in solution and in supramolecular organogels. Gelation occurs in toluene through hydrogen bonding and van der Waals interactions for 1 and 2 in addition to pp stacking specifically in the case of 1. These nanocomposites provide a thorough understanding in terms of molecular-level interactions of dimensionally different CNMs with structurally different gelators. The presence of densely wrapped CNMs encapsulated fibrous network in the resulting composites is evident from various spectroscopic and microscopic studies, indicating the presence of supramolecular interactions. Concentration- and temperature-dependent UV/Vis and fluorescence spectra show that CNMs promote aggregation of the gelator molecules, leading to hypochromism and quenching of the fluorescence intensity. Thermotropic mesophases of 1 are altered by the inclusion of a small amount of CNMs. The gelCNM composites show increased electrical conductivity compared with that of the native organogel. Rheological studies of the composites demonstrate the formation of rigid and viscoelastic solidlike assembly due to reinforced aggregation of the gelators on CNMs. Synergistic behavior is observed in case of the composite gel of 1, containing a mixture of EG and SWNT, when compared with other mixtures of CNMs in all combinations with EG. This affords new nanocomposites with interesting optical, thermal, electrical, and mechanical properties.

Gap renormalization of molecular crystals from density-functional theory

Fundamental gap renormalization due to electronic polarization is a basic phenomenon in molecular crystals. Despite its ubiquity and importance, all conventional approaches within density-functional theory completely fail to capture it, even qualitatively. Here, we present a new screened range-separated hybrid functional, which, through judicious introduction of the scalar dielectric constant, quantitatively captures polarization-induced gap renormalization, as demonstrated on the prototypical organic molecular crystals of benzene, pentacene, and C-60. This functional is predictive, as it contains system-specific adjustable parameters that are determined from first principles, rather than from empirical considerations.

A Rodinian suture in western India: New insights on India-Madagascar correlations

We report detailed evidence for a new paleo-suture zone (the Kumta suture) on the western margin of southern India. The c. 15-km-wide, westward dipping suture zone contains garnet-biotite, fuchsite-haematite, chlorite-quartz, quartz-phengite schists, biotite augen gneiss, marble and amphibolite. The isochemical phase diagram estimations and the high-Si phengite composition of quartz-phengite schist suggest a near-peak condition of c. 18 kbar at c. 550 degrees C, followed by near-isothermal decompression. The detrital SHRIMP U-Pb zircon ages from quartz-phengite schist give four age populations ranging from 3280 to 2993 Ma. Phengite from quartz-phengite schist and biotite from garnet-biotite schist have K-Ar metamorphic ages of ca. 1326 and ca. 1385 Ma respectively. Electron microprobe-CHIME ages of in situ zircons in quartz-phengite schist (ca. 3750 Ma and ca. 1697 Ma) are consistent with the above results. The Bondla ultramafic-gabbro complex in the west of the Kumta suture compositionally represents an arc with K-Ar biotite ages from gabbro in the range 1644-1536 Ma. On the eastern side of the suture are weakly deformed and unmetamorphosed shallow westward-dipping sedimentary rocks of the Sirsi shelf, which has the following upward stratigraphy: pebbly quartzite/sandstone, turbidite, magnetite iron formation, and limestone; farther east the lower lying quartzite has an unconformable contact with ca. 2571 Ma quartzo-feldspathic gneisses of the Dharwar block with a ca. 1733 Ma biotite cooling age. To the west of the suture is a c. 60-km-wide Karwar block mainly consisting of tonalite-trondhjemite-granodiorite (TTG) and amphibolite. The TTGs have U-Pb zircon magmatic ages of ca. 3200 Ma with a rare inherited core age of ca. 3601 Ma. The K-Ar biotite cooling age from the TTGs (1746 Ma and 1796 Ma) and amphibolite (ca. 1697 Ma) represents late-stage uplift. Integration of geological, structural and geochronological data from western India and eastern Madagascar suggest diachronous ocean closure during the amalgamation of Rodinia; in the north at around ca. 1380 Ma, and a progression toward the south until ca. 750 Ma. Satellite imagery based regional structural lineaments suggests that the Betsimisaraka suture continues into western India as the Kumta suture and possibly farther south toward a suture in the Coorg area, representing in total a c. 1000 km long Rodinian suture. (C) 2013 Elsevier B.V. All rights reserved.

Investigation Of Mode Ii Crack Growth Following A Very High Speed Impact

A recoverable plate impact testing technology has been developed for studying fracture mechanisms of mode II crack. With this technology, a single duration stress pulse with submicrosecond duration and high loading rates, up to 10(8) MPam(1/2)s(-1), can be produced. Dynamic failure tests of Hard-C 60# steel were carried out under asymmetrical impacting conditions with short stress-pulse loading. Experimental results show that the nucleation and growth of several microcracks ahead of the crack tip, and the interactions between them, induce unsteady crack growth. Failure mode transitions during crack growth, both from mode I crack to mode II and from brittle to ductile fracture, were observed. Based on experimental observations, a discontinuous crack growth model was established. Analysis of the crack growth mechanisms using our model shows that the shear crack extension is unsteady when the extending speed is between the Rayleigh wave speed c(R) and the shear wave speed c(S). However, when the crack advancing speed is beyond c(S), the crack grows at a steady intersonic speed approaching root 2c(S). It also shows that the transient mechanisms, such as nucleation, growth, interaction and coalescence among microcracks, make the main crack speed jump from subsonic to intersonic and the steady growth of all the subcracks causes the main crack to grow at a stable intersonic speed.

Desarrollo de nanopartículas sólidas lipídicas como sistemas de administración de ADN para terapia génica

290 p. (Bibliogr. 257-290) Correo electrónico de la autora: ana.delpozo@ehu.es

Optimization of solution-processed oligothiophene:fullerene based organic solar cells by using solvent additives

The optimization of solution-processed organic bulk-heterojunction solar cells with the acceptor-substituted quinquethiophene DCV5T-Bu-4 as donor in conjunction with PC61BM as acceptor is described. Power conversion efficiencies up to 3.0% and external quantum efficiencies up to 40% were obtained through the use of 1-chloronaphthalene as solvent additive in the fabrication of the photovoltaic devices. Furthermore, atomic force microscopy investigations of the photoactive layer gave insight into the distribution of donor and acceptor within the blend. The unique combination of solubility and thermal stability of DCV5T-Bu-4 also allows for fabrication of organic solar cells by vacuum deposition. Thus, we were able to perform a rare comparison of the device characteristics of the solution-processed DCV5T-Bu-4:PC61BM solar cell with its vacuum-processed DCV5T-Bu-4:C-60 counterpart. Interestingly in this case, the efficiencies of the small-molecule organic solar cells prepared by using solution techniques are approaching those fabricated by using vacuum technology. This result is significant as vacuum-processed devices typically display much better performances in photovoltaic cells. Keywords

Improvement in the nutritive quality of soyabean meal by co-ensiling with under-utilized fish discards

Improvement in the nutritive value of soybean meal was investigated by Co-ensiling it with underutilized trash fish discards (gizzard shad)at different proportions. The following proportions of gizzard shad to soybean meal were used; (a) 100% gizzard shad + acid combination (b)80% gizzard shad +20% soybean meal & 10% WB (c) 60% gizzard shad + 40% soybean meal & 10% WB (d) 100% gizzard shad without acid combination. Co-ensiling was achieved by adding sufficient acid to produce a paste. Products were neutralized by addition of 2% (by weight) calcium hydroxide and drying was affected by freeze-drying.The dried silage products were stored at low temperatures. Products were analysed for proximate composition and amino acid composition.The amino acid composition and ration of essential amino acid. Non essential amino acid (EAA/NEAA) was used as index of nutritive quality. Also essential amino acid profile of the co-ensiled products were compared with essential amino acid requirement of some warmwater fish species to estimate their nutritive usefulness for these species