Erosion Control for Highway Applications, Phase I: Review and Synthesis of Literature, Final Report, TR-464, May 2002

The project described herein has led to a convenient, computer-based expert system for identifying and evaluating potentially effective erosion- and sedimentation-control measures for use in roadway construction throughout Iowa and elsewhere in the Midwest. The expert system is intended to be an accessible and efficient practical resource to aid state, county, and municipal engineers in the selection of the best management practices for preventing unwanted erosion and sedimentation at roadway construction sites, during and after construction.

Embankment Quality, TR-401, Phase I, 1998

Phase I was initiated as a result of internal Iowa Department of Transportation (Iowa DOT) studies that raised concerns about the quality of embankments being constructed. Some large embankments have recently developed slope stability problems. In addition, pavement roughness has been noted shortly after roads were opened to traffic. This raised the question as to whether the current Iowa DOT embankment construction specifications are adequate. The primary objective of Phase I was to evaluate the quality of embankments being constructed under the current Iowa DOT specifications. The project was initiated in May 1997 with a tour of several embankment projects being constructed around the state. At each of these projects the resident construction engineer, field inspector, and contractor were interviewed with respect to their opinion of the current specifications. From construction observations and discussion during these visits it became obvious that there were problems with the current embankment construction specifications. Six embankment projects were selected for in-depth analysis and to represent the full range of soil types being used across the state. The results of Phase I field and laboratory construction testing and observations and post construction testing are presented in this report. Overall evaluation of the results of Phase I indicate that Iowa is not consistently obtaining a quality embankment constructed under the current Iowa DOT specifications. Based on these results, recommendations are made for Phase II to evaluate alternative specifications and develop rapid field methods for compaction control and soil identification.

Randomized double-blind controlled Phase I/IIa trial to assess the efficacy of malaria vaccine PfCS102 to protect against challenge with P. falciparum.

The aim of this Phase I/IIa double-blind controlled trial was to test the efficacy of the sporozoite-based malaria vaccine PfCS 282-383 (PfCS102) to protect against Plasmodium falciparum parasitaemia. 16 volunteers were randomized to receive twice 30 μg of PfCS102 formulated in Montanide ISA 720 or ISA 720 alone (control). Two weeks after 2nd immunization, volunteers were challenged using 5 infected mosquitoes. All vaccinees developed antibodies against PfCS102 versus none control. 8/8 vaccinees and 6/6 controls challenged developed malaria parasitaemia. The duration from infection to onset of patent parasitaemia was similar in both groups (214 h in vaccinees and 216 in controls). PfCS102 is safe and immunogenic but provides no protection against artificial challenge in its current formulation.

General unknown screening procedure for the characterization of human drug metabolites: application to loratadine phase I metabolism.

This article describes the application of a recently developed general unknown screening (GUS) strategy based on LC coupled to a hybrid linear IT-triple quadrupole mass spectrometer (LC-MS/MS-LIT) for the simultaneous detection and identification of drug metabolites following in vitro incubation with human liver microsomes. The histamine H1 receptor antagonist loratadine was chosen as a model compound to demonstrate the interest of such approach, because of its previously described complex and extensive metabolism. Detection and mass spectral characterization were based on data-dependent acquisition, switching between a survey scan acquired in the ion-trapping Q3 scan mode with dynamic subtraction of background noise, and a dependent scan in the ion-trapping product ion scan mode of automatically selected parent ions. In addition, the MS(3) mode was used in a second step to confirm the structure of a few fragment ions. The sensitivity of the ion-trapping modes combined with the selectivity of the triple quadrupole modes allowed, with only one injection, the detection and identification of 17 phase I metabolites of loratadine. The GUS procedure used in this study may be applicable as a generic technique for the characterization of drug metabolites after in vitro incubation, as well as probably in vivo experiments.

Thin Maintenance Surfaces - Phase I, TR-435, 1999

The first phase of a two-phase research project was conducted to develop guidelines for Iowa transportation officials on the use of thin maintenance surfaces (TMS) for asphaltic concrete and bituminous roads. Thin maintenance surfaces are seal coats (chip seals), slurry seals, and micro-surfacing. Interim guidelines were developed to provide guidance on which roads are good candidates for TMS, when TMS should be placed, and what type of thin maintenance surface should be selected. The guidelines were developed specifically for Iowa aggregates, weather, traffic conditions, road user expectations, and transportation official expectations. In addition to interim guidelines, this report presents recommendations for phase-two research. It is recommended that test section monitoring continue and that further investigations be conducted regarding thin maintenance surface aggregate, additional test sections, placed, and a design method adopted for seal coats.

Optimal priming of poxvirus vector (NYVAC)-based HIV vaccine regimens requires 3 DNA injections. Results of the EV03/ANRS Vac20 Phase I/II Trial

Background: Two or three DNA primes have been used in previous smaller clinical trials, but the number required for optimal priming of viral vectors has never been assessed in adequately powered clinical trials. The EV03/ANRS Vac20 phase I/II trial investigated this issue using the DNA prime/poxvirus NYVAC boost combination, both expressing a common HIV-1 clade C immunogen consisting of Env and Gag-Pol-Nef polypeptide. Methods: 147 healthy volunteers were randomly allocated through 8 European centres to either 3xDNA plus 1xNYVAC (weeks 0, 4, 8 plus 24; n¼74) or to 2xDNA plus 2xNYVAC (weeks 0, 4 plus 20, 24; n¼73), stratified by geographical region and sex. T cell responses were quantified using the interferon g Elispot assay and 8 peptide pools; samples from weeks 0, 26 and 28 (time points for primary immunogenicity endpoint), 48 and 72 were considered for this analysis. Results: 140 of 147 participants were evaluable at weeks 26 and/ or 28. 64/70 (91%) in the 3xDNA arm compared to 56/70 (80%) in the 2xDNA arm developed a T cell response (P¼0.053). 26 (37%) participants of the 3xDNA arm developed a broader T cell response (Env plus at least to one of the Gag, Pol, Nef peptide pools) versus 15 (22%) in the 2xDNA arm (P¼0.047). At week 26, the overall magnitude of responses was also higher in the 3xDNA than in the 2xDNA arm (similar at week 28), with a median of 545 versus 328 SFUs/106 cells at week 26 (P<0.001). Preliminary overall evaluation showed that participants still developed T-cell response at weeks 48 (78%, n¼67) and 72 (70%, n¼66). Conclusion: This large clinical trial demonstrates that optimal priming of poxvirus-based vaccine regimens requires 3 DNA regimens and further confirms that the DNA/NYVAC prime boost vaccine combination is highly immunogenic and induced durable T-cell responses.

Control of Concrete Deterioration Due to Trace Compounds in Deicers, HR-299 Phase I, 1988

This report presents the results of research on the influence of trace compounds from rock salt deicers on portland cement mortar and concrete. An evaluation of the deicers in stock throughout the state showed that about ninety-five percent contained enough sulfate to cause accelerated deterioration of concrete. Of the impurities found in rock salts, sulfate compounds of calcium and magnesium were found to be equally deleterious. Magnesium chloride was found to be innocuous. Introduction of fly ash eliminated the damage to portland cement mortar caused by sulfates. When used with frost resistant Alden aggregate in fly ash concrete and exposed to a variety of deicer brine compositions, the concrete did not deteriorate after exposure. With the exception of a high calcium brine, the behavior of the frost-prone Garrison aggregate was independent of deicer treatment; the high calcium brine reduced frost damage with this aggregate. Two approaches to reducing sulfate deterioration from deicers are suggested as (1) limiting the amount of sulfate to about 0.28 percent, and (2) making concrete sulfate-resistant by using fly ash. Techniques for making existing concrete deicer-sulfate-resistant are essential to a practical solution.

Freeze-Thaw Durability of Concretes with and without Class C Fly Ash, MLR-94-9 Phase I, 1997

The freeze-thaw resistance of concretes was studied. Nine concrete mixes, made with five cements and cement-Class C fly ash combinations, were exposed to freeze-thaw cycling following 110 to 222 days of moist curing. Prior to the freeze-thaw cycling, the specimens were examined by a low-vacuum scanning electron microscope (SEM) for their microstructure. The influence of a wet/dry treatment was also studied. Infilling of ettringite in entrained air voids was observed in the concretes tested. The extent of the infilling depends on the period of moist curing as well as the wet/dry treatment. The concretes with 15% Class C fly ash replacement show more infilling in their air voids. It was found that the influence of the infilling on the freeze-thaw durability relates to the air spacing factor. The greater the spacing factor, the more expansion under the freeze-thaw cycling. The infilling seems to decrease effective air content and to increase effective spacing factor. The infilling also implies that the filled air voids are water-accessible. These might lead to concrete more vulnerable to the freeze-thaw attack. By combining the above results with field observations, one may conclude that the freeze-thaw damage is a factor related to premature deterioration of portland cement concrete pavements in Iowa.

Alternate Methods of Stabilizing Degrading Stream Channels in Western Iowa, Phase I, HR-208, 1980

Since the beginning of channel straightening at the turn of the century, the streams of western Iowa have degraded 1.5 to 5 times their original depth. This vertical degradation is often accompanied by increases in channel widths of 2 to 4 times the original widths. The deepening and widening of these streams has jeopardized the structural safety of many bridges by undercutting footings or pile caps, exposing considerable length of piling, and removing soil beneath and adjacent to abutments. Various types of flume and drop structures have been introduced in an effort to partially or totally stabilize these channels, protecting or replacing bridge structures. Although there has always been a need for economical grade stabilization structures to stop stream channel degradation and protect highway bridges and culverts, the problem is especially critical at the present time due to rapidly increasing construction costs and decreasing revenues. Benefits derived from stabilization extend beyond the transportation sector to the agricultural sector, and increased public interest and attention is needed.

Standards for Single Span Prefabricated Bridges, Phase I - Concept Development, TR-663, 2014

In coordination with a Technical Advisory Committee (TAC) consisting of County Engineers and Iowa DOT representatives, the Iowa DOT has proposed to develop a set of standards for a single span prefabricated bridge system for use on the local road system. The purpose of the bridge system is to improve bridge construction, accelerate project delivery, improve worker safety, be cost effective, reduce impacts to the travelling public by reducing traffic disruptions and the duration of detours, and allow local forces to construct the bridges. HDR Inc. was selected by the Iowa DOT to perform the initial concept screening of the bridge system. This Final Report summarizes the initial conceptual effort to investigate potential systems, make recommendations for a preferred system and propose initial details to be tested in the laboratory in Phase 2 of the project. The prefabricated bridge components were to be based on the following preliminary criteria set forth by the TAC. The criteria were to be verified and/ or modified as part of the conceptual development. - 24’ and 30’ roadway widths - Skews of 0o, 15o, and 30o - Span lengths of 30’ – 70’ in 10’ increments using precast concrete beams - Voided box beams could be considered - Limit precast element weight to 45,000 pounds for movement and placement of beams - Beams could be joined transversely with threaded rods - Abutment concepts may included precast as well as an option for cast-in-place abutments with pile foundations In addition to the above criteria, there was an interest to use a single-width prefabricated bridge component to simplify fabrication as well as a desire to utilize non-prestressed concrete systems where possible to allow for precasting of the beam modules by local forces or local precast plants. The SL-1 modular steel bridge rail was identified for use with this single span prefabricated bridge system.

Evaluation des Nationalen Krebsbekämpfungsprogrammes, Phase I, 1999. Studie 2: Inventar der vorhandenen Datenquellen und Indikatoren

[Table des matières] 1. Allgemeine Schlussforschungen und Empfehlungen. 2. Einleitung. 3. Methodik. 4. Ergebnisse. 4.1. Zentrale Datenquellen : Kontinuierliche und periodische Erhabungen, Mortalitätsstatistik, Spitalstatistik, Vereinigung Schweizerischer Krebsregister, Schweizerische Gesundheitsbefragung, Trendstudie zum Konsum von Alkohol, Tabak, Medikamenten und illegalen Drogen SFA, SChülerbefragung SFA, Warenkorb BFS, Schweizer Haushalt-Panel, Traditioneller Haushaltspanel IHA-GfM, Pharmaabsatzzahlen IHA-GfM, Sonnenexposition und Sonnenschutz, Indikatoren für den Tabakkonsum in der Schweiz, Statistische Erhebungen und Schätzungen über Landwirtschaft und Ernährung, Participants' Report SIAK, Trial guide SAKK, Guidelines, Berufskrankheiten SUVA, Krebstelefon SKL. 4.2. Weitere Datenquellen : Kontinuierliche und periodische Erhebungen, Statistik der verteilten Broschüren SKL, Jahresbericht von im Bereich Krebs tätigen Institutionen, Invalidenversicherung BSV, Andere Statistiken des BSV, Konkordat der Schweizerischen Krankenversicherer, Nestlé-Studie. 4.3. Zentrale Einzelerhebungen : Frauen und Krebs, Vorstudie für eine nationale Kampagne zur Früherfassung des kolorektalen Karzinoms, Ausmass und Intensität von Krebsschmerzen in der Schweiz. 4.4. Weitere Einzelerhebungen : IUMSP : die Gesundheit Jugendlicher in der Schweiz, Stillhäufigkeit und Stilldauer in der Schweiz 1994, Kohortenstudie Alkohol- und Drogenkonsum SFA. 4.5. Abgeschlossene Erhebungen : Krebsvorsorge, MONICA-Studie und Basler Ernährungsstudie. 5. Schlussfolgerungen und Empfehlungen : Zusammenfassende Schlussfolgerungen und Empfehlungen. 6. Anhang. 6.1. Zentrale Datenquellen im Uberblick : Globalkonzept, Brustkrebsprogramm, Lungenkrebsprogramm, Hautkrebsprogramm, Darmkrebsprogramm. 6.2. Zieltabelle : formulierte Ziele des nationalen Krebsbekämpfungsprogramms. 6.3. Abkürzungen.

Rapid Replacement of Bridge Deck Expansion Joints Study – Phase I, RB33-013, 2014

Bridge deck expansion joints are used to allow for movement of the bridge deck due to thermal expansion, dynamics loading, and other factors. More recently, expansion joints have also been utilized to prevent the passage of winter de-icing chemicals and other corrosives applied to bridge decks from penetrating and damaging substructure components of the bridge. Expansion joints are often one of the first components of a bridge deck to fail and repairing or replacing expansion joints are essential to extending the life of any bridge. In the Phase I study, the research team focused on the current means and methods of repairing and replacing bridge deck expansion joints. Research team members visited with Iowa Department of Transportation (DOT) Bridge Crew Leaders to document methods of maintaining and repairing bridge deck expansion joints. Active joint replacement projects around Iowa were observed to document the means of replacing expansion joints that were beyond repair, as well as, to identify bottlenecks in the construction process that could be modified to decrease the length of expansion joint replacement projects. After maintenance and replacement strategies had been identified, a workshop was held at the Iowa State Institute for Transportation to develop ideas to better maintain and replace expansion joints. Maintenance strategies were included in the discussion as a way to extend the useful life of a joint, thus decreasing the number of joints replaced in a year and reducing the traffic disruptions.

Portland Cement Concrete Curing Compound Performance Phase I and Phase II, MLR-02-03, 2003

Testing the efficiency of Portland Cement Concrete (PCC) curing compounds is currently done following Test Method Iowa 901-D, May 2002. Concrete test specimens are prepared from mortar materials and are wet cured 5 hours before the curing compound is applied. All brands of curing compound submitted to the Iowa Department of Transportation are laboratory tested for comparative performance under the same test conditions. These conditions are different than field PCC paving conditions. Phase I tests followed Test Method Iowa 901-D, but modified the application amounts of the curing compound. Test results showed that the application of two coats of one-half thickness each increased efficiency compared to one full thickness coat. Phase II tests also used the modified application amounts, used a concrete mix (instead of a mortar mix) and applied curing compound a few minutes after molding. Measurements of losses, during spraying of the curing compound, were noted and were found to be significant. Test results showed that application amounts, testing techniques, concrete specimen mix design and spray losses do influence the curing compound efficiency. The significance of the spray losses indicates that the conventional test method being used (Iowa 901 D) should be revised.

Development of Object-Oriented Design and Specifications for Iowa DOT and Urban Standards: Phase I, TR-487, 2004

Currently, individuals including designers, contractors, and owners learn about the project requirements by studying a combination of paper and electronic copies of the construction documents including the drawings, specifications (standard and supplemental), road and bridge standard drawings, design criteria, contracts, addenda, and change orders. This can be a tedious process since one needs to go back and forth between the various documents (paper or electronic) to obtain information about the entire project. Object-oriented computer-aided design (OO-CAD) is an innovative technology that can bring a change to this process by graphical portrayal of information. OO-CAD allows users to point and click on portions of an object-oriented drawing that are then linked to relevant databases of information (e.g., specifications, procurement status, and shop drawings). The vision of this study is to turn paper-based design standards and construction specifications into an object-oriented design and specification (OODAS) system or a visual electronic reference library (ERL). Individuals can use the system through a handheld wireless book-size laptop that includes all of the necessary software for operating in a 3D environment. All parties involved in transportation projects can access all of the standards and requirements simultaneously using a 3D graphical interface. By using this system, users will have all of the design elements and all of the specifications readily available without concerns of omissions. A prototype object-oriented model was created and demonstrated to potential users representing counties, cities, and the state. Findings suggest that a system like this could improve productivity to find information by as much as 75% and provide a greater sense of confidence that all relevant information had been identified. It was also apparent that this system would be used by more people in construction than in design. There was also concern related to the cost to develop and maintain the complete system. The future direction should focus on a project-based system that can help the contractors and DOT inspectors find information (e.g., road standards, specifications, instructional memorandums) more rapidly as it pertains to a specific project.