Adaptation of LEACH routing protocol to cognitive radio sensor networks

One of the drawbacks of LEACH protocol is the uncontrolled selection of cluster heads which, in some rounds, leads to the concentration of them in a limited area due to the randomness of the selection procedure. LEACH-C is a variant of LEACH that uses a centralized clustering algorithm and forms good clusters through sink control. According to experimental results, the IEEE 802.15.4 packets are damaged by WLAN interferences in ISM band. It seems that, sensor nodes equipped with cognitive radio capabilities can overcome this problem. In cognitive radio sensor networks (CRSN), routing must be accompanied by channel allocation. This requires spectrum management which can be devolved to cluster heads. For this networks, new duty cycle mechanisms must be designed that jointly consider neighbor discovery, and spectrum sensing/allocation. Cluster-based network architecture is a good choice for effective dynamic spectrum management. In such architecture, cluster heads have a proper spatial distribution and are optimally located all over the network. In this paper, using the physical layer information and preserving the feature of random cluster head selection in LEACH, it has been tried to both move the position of cluster heads to appropriate locations and make their quantity optimal. The simulation results show that the transferal of cluster heads to appropriate locations increases the network lifetime significantly though this comes at the price of early instability appearance. By considering the energy level in cluster head election algorithm, one can overcome the network stability issues too. However, this will move the cluster heads away from their appropriate locations. © 2012 IEEE.

A Time-based Passive Source Localization System for Narrow-band Signal

Time-based indoor localization has been investigated for several years but the accuracy of existing solutions is limited by several factors, e.g., imperfect synchronization, signal bandwidth and indoor environment. In this paper, we compare two time-based localization algorithms for narrow-band signals, i.e., multilateration and fingerprinting. First, we develop a new Linear Least Square (LLS) algorithm for Differential Time Difference Of Arrival (DTDOA). Second, fingerprinting is among the most successful approaches used for indoor localization and typically relies on the collection of measurements on signal strength over the area of interest. We propose an alternative by constructing fingerprints of fine-grained time information of the radio signal. We offer comprehensive analytical discussions on the feasibility of the approaches, which are backed up by evaluations in a software defined radio based IEEE 802.15.4 testbed. Our work contributes to research on localization with narrow-band signals. The results show that our proposed DTDOA-based LLS algorithm obviously improves the localization accuracy compared to traditional TDOA-based LLS algorithm but the accuracy is still limited because of the complex indoor environment. Furthermore, we show that time-based fingerprinting is a promising alternative to power-based fingerprinting.

Range-based Weighted-likelihood Particle Filter for RSS-based Indoor Tracking

Attractive business cases in various application fields contribute to the sustained long-term interest in indoor localization and tracking by the research community. Location tracking is generally treated as a dynamic state estimation problem, consisting of two steps: (i) location estimation through measurement, and (ii) location prediction. For the estimation step, one of the most efficient and low-cost solutions is Received Signal Strength (RSS)-based ranging. However, various challenges - unrealistic propagation model, non-line of sight (NLOS), and multipath propagation - are yet to be addressed. Particle filters are a popular choice for dealing with the inherent non-linearities in both location measurements and motion dynamics. While such filters have been successfully applied to accurate, time-based ranging measurements, dealing with the more error-prone RSS based ranging is still challenging. In this work, we address the above issues with a novel, weighted likelihood, bootstrap particle filter for tracking via RSS-based ranging. Our filter weights the individual likelihoods from different anchor nodes exponentially, according to the ranging estimation. We also employ an improved propagation model for more accurate RSS-based ranging, which we suggested in recent work. We implemented and tested our algorithm in a passive localization system with IEEE 802.15.4 signals, showing that our proposed solution largely outperforms a traditional bootstrap particle filter.

Análisis e implementación de estrategias de rutado dinámico basado en CTP para redes de sensores inalámbricas multi-salto

Una red de sensores inalámbrica es un conjunto de dispositivos electrónicos que se comunican entre sí sin la necesidad de una infraestructura, recogiendo información del entorno en el que han sido desplegados, procesándola y transmitiéndola hasta una estación base mediante saltos sucesivos entre los nodos de la red (multi-salto). Durante las dos últimas décadas, este campo ha sido muy desarrollado en la comunidad científica, debido a las ventajas que ofrece el despliegue de una red inalámbrica en un entorno con el fin de estudiarlo y/o controlarlo. La ausencia de una infraestructura, junto con el reducido tamaño de los nodos, permite este estudio sin que dicho entorno se vea significativamente afectado por factores externos como pueda ser la presencia humana, permitiendo además aumentar el número de nodos que componen la red o cambiar la posición de algunos de ellos sin que sea necesario reconfigurarla manualmente. El principal reto que presentan las redes de sensores inalámbricas es su autonomía. En general, se requiere que un nodo tenga la capacidad de funcionar durante largos períodos de tiempo (varios meses o incluso un año) antes de que su batería se agote. Esto hace de la gestión del consumo energético un aspecto crítico en el diseño de la red y sus nodos. En el presente trabajo se busca optimizar este consumo mediante la gestión del proceso de comunicación y enrutamiento de la red. Con este fin, se implementa el protocolo CTP (Collection Tree Protocol) en la plataforma Cookies desarrollada en el Centro de Electrónica Industrial (CEI) de la UPM. CTP es un protocolo de rutado centrado en los datos, que utiliza una topología en árbol, con el nodo coordinador o estación base como raíz del mismo, para la transmisión de la información desde los sensores hasta la estación base. Además, no utiliza direcciones predeterminadas, dotando a la red de la flexibilidad requerida para hacer frente a inconsistencias y/o variaciones en la densidad y tamaño de la red. La ruta escogida se basa en un gradiente de rutado decreciente, ETX (Expected Transmission Count), que representa la calidad de la conexión entre un nodo y su nodo padre. Este gradiente de enrutamiento se obtiene mediante una conversión directa a partir del LQI (Link Quality Indication) definido por el estándar IEEE 802.15.4. Esta conversión directa supone una aproximación utilizando valores umbral del LQI. Un nodo escogerá el siguiente salto que realizará el paquete a enviar seleccionando de entre sus vecinos a aquél que tenga el menor ETX, evitando de esta forma la aparición de bucles. Otro de los aspectos que supone un gran consumo es el proceso de mantenimiento de la estructura de la red, pues requiere el envío periódico de señales de control o beacons a lo largo de toda la red. El protocolo CTP aprovecha el algoritmo de goteo (Trickle Algorithm), para gestionar el mantenimiento: durante la formación de la red y cuando se detecte alguna inconsistencia, se incrementa la frecuencia de emisión de los beacons, permitiendo así una rápida propagación de las señales de control para crear o reparar las conexiones entre los nodos. En cambio, cuando la topología de la red es estable, esta frecuencia de emisión se reduce significativamente, limitándose a asegurar que la topología se mantiene estable y favoreciendo así el ahorro de energía.

Stochastic models of IEEE 802.11e wireless net works with multimedia applications

We provide a survey of some of our recent results ([9], [13], [4], [6], [7]) on the analytical performance modeling of IEEE 802.11 wireless local area networks (WLANs). We first present extensions of the decoupling approach of Bianchi ([1]) to the saturation analysis of IEEE 802.11e networks with multiple traffic classes. We have found that even when analysing WLANs with unsaturated nodes the following state dependent service model works well: when a certain set of nodes is nonempty, their channel attempt behaviour is obtained from the corresponding fixed point analysis of the saturated system. We will present our experiences in using this approximation to model multimedia traffic over an IEEE 802.11e network using the enhanced DCF channel access (EDCA) mechanism. We have found that we can model TCP controlled file transfers, VoIP packet telephony, and streaming video in the IEEE802.11e setting by this simple approximation.

Improved power-saving medium access protocol for IEEE 802.11e QoS-enabled wireless networks

The performance of a new pointer-based medium-access control protocol that was designed to significantly improve the energy efficiency of user terminals in quality-of-service-enabled wireless local area networks was analysed. The new protocol, pointer-controlled slot allocation and resynchronisation protocol (PCSARe), is based on the hybrid coordination function-controlled channel access mode of the IEEE 802.11e standard. PCSARe reduces energy consumption by removing the need for power-saving stations to remain awake for channel listening. Discrete event network simulations were performed to compare the performance of PCSARe with the non-automatic power save delivery (APSD) and scheduled-APSD power-saving modes of IEEE 802.11e. The simulation results show a demonstrable improvement in energy efficiency without significant reduction in performance when using PCSARe. For a wireless network consisting of an access point and eight stations in power-saving mode, the energy saving was up to 39% when using PCSARe instead of IEEE 802.11e non-APSD. The results also show that PCSARe offers significantly reduced uplink access delay over IEEE 802.11e non-APSD, while modestly improving the uplink throughput. Furthermore, although both had the same energy consumption, PCSARe gave a 25% reduction in downlink access delay compared with IEEE 802.11e S-APSD.

Peak-to-average power ratio of IEEE 802.11a PHY layer signals

In this chapter we propose clipping with amplitude and phase corrections to reduce the peak-to-average power ratio (PAR) of orthogonal frequency division multiplexed (OFDM) signals in high-speed wireless local area networks defined in IEEE 802.11a physical layer. The proposed techniques can be implemented with a small modification at the transmitter and the receiver remains standard compliant. PAR reduction as much as 4dB can be achieved by selecting a suitable clipping ratio and a correction factor depending on the constellation used. Out of band noise (OBN) is also reduced.

Securing IEEE 802.11 wireless LANs

As the acceptance and popularity of wireless networking technologies has proliferated, the security of the IEEE 802.11 wireless local area network (WLAN) has advanced in leaps and bounds. From tenuous beginnings, where the only safe way to deploy a WLAN was to assume it was hostile and employ higherlayer information security controls, to the current state of the art, all manner of improvements have been conceived and many implemented. This work investigates some of the remaining issues surrounding IEEE 802.11 WLAN operation. While the inherent issues in WLAN deployments and the problems of the original Wired Equivalent Privacy (WEP) provisions are well known and widely documented, there still exist a number of unresolved security issues. These include the security of management and control frames and the data link layer protocols themselves. This research introduces a novel proposal to enhance security at the link layer of IEEE 802.11 WLANs and then conducts detailed theoretical and empirical investigation and analysis of the eects of such proposals. This thesis �rst de�nes the state of the art in WLAN technology and deployment, including an overview of the current and emerging standards, the various threats, numerous vulnerabilities and current exploits. The IEEE 802.11i MAC security enhancements are discussed in detail, along with the likely outcomes of the IEEE 802.11 Task Group W1, looking into protected management frames. The problems of the remaining unprotected management frames, the unprotected control frames and the unprotected link layer headers are reviewed and a solution is hypothesised, to encrypt the entire MAC Protocol Data Unit (MPDU), including the MAC headers, not just the MAC Service Data Unit (MSDU) commonly performed by existing protocols. The proposal is not just to encrypt a copy of the headers while still using cleartext addresses to deliver the frame, as used by some existing protocols to support the integrity and authenticity of the headers, but to pass the entire MPDU only as ciphertext to also support the con�dentiality of the frame header information. This necessitates the decryption of every received frame using every available key before a station can determine if it is the intended recipient. As such, this raises serious concerns as to the viability of any such proposal due to the likely impact on throughput and scalability. The bulk of the research investigates the impacts of such proposals on the current WLAN protocols. Some possible variations to the proposal are also provided to enhance both utility and speed. The viability this proposal with respect to the eect on network throughput is then tested using a well known and respected network simulation tool, along with a number of analysis tools developed speci�cally for the data generated here. The simulator's operation is �rst validated against recognised test outputs, before a comprehensive set of control data is established, and then the proposal is tested and and compared against the controls. This detailed analysis of the various simulations should be of bene�t to other researchers who need to validate simulation results. The analysis of these tests indicate areas of immediate improvement and so the protocols are adjusted and a further series of experiments conducted. These �nal results are again analysed in detail and �nal appraisals provided.

Markov modelling of the IEEE 802.11 DCF for real-time applications with periodic traffic

Popular wireless network standards, such as IEEE 802.11/15/16, are increasingly adopted in real-time control systems. However, they are not designed for real-time applications. Therefore, the performance of such wireless networks needs to be carefully evaluated before the systems are implemented and deployed. While efforts have been made to model general wireless networks with completely random traffic generation, there is a lack of theoretical investigations into the modelling of wireless networks with periodic real-time traffic. Considering the widely used IEEE 802.11 standard, with the focus on its distributed coordination function (DCF), for soft-real-time control applications, this paper develops an analytical Markov model to quantitatively evaluate the network quality-of-service (QoS) performance in periodic real-time traffic environments. Performance indices to be evaluated include throughput capacity, transmission delay and packet loss ratio, which are crucial for real-time QoS guarantee in real-time control applications. They are derived under the critical real-time traffic condition, which is formally defined in this paper to characterize the marginal satisfaction of real-time performance constraints.

Modelling and performance evaluation of the IEEE 802.11 DCF for real-time control

Popular wireless networks, such as IEEE 802.11/15/16, are not designed for real-time applications. Thus, supporting real-time quality of service (QoS) in wireless real-time control is challenging. This paper adopts the widely used IEEE 802.11, with the focus on its distributed coordination function (DCF), for soft-real-time control systems. The concept of the critical real-time traffic condition is introduced to characterize the marginal satisfaction of real-time requirements. Then, mathematical models are developed to describe the dynamics of DCF based real-time control networks with periodic traffic, a unique feature of control systems. Performance indices such as throughput and packet delay are evaluated using the developed models, particularly under the critical real-time traffic condition. Finally, the proposed modelling is applied to traffic rate control for cross-layer networked control system design.

Experiences With WM: A Centralised Scheduling Approach for Performance Management of IEEE 802.11 Wireless LANs

In our earlier work ([1]) we proposed WLAN Manager (or WM) a centralised controller for QoS management of infrastructure WLANs based on the IEEE 802.11 DCF standards. The WM approach is based on queueing and scheduling packets in a device that sits between all traffic flowing between the APs and the wireline LAN, requires no changes to the AP or the STAs, and can be viewed as implementing a "Split-MAC" architecture. The objectives of WM were to manage various TCP performance related issues (such as the throughput "anomaly" when STAs associate with an AP with mixed PHY rates, and upload-download unfairness induced by finite AP buffers), and also to serve as the controller for VoIP admission control and handovers, and for other QoS management measures. In this paper we report our experiences in implementing the proposals in [1]: the insights gained, new control techniques developed, and the effectiveness of the WM approach in managing TCP performance in an infrastructure WLAN. We report results from a hybrid experiment where a physical WM manages actual TCP controlled packet flows between a server and clients, with the WLAN being simulated, and also from a small physical testbed with an actual AP.

Analytical models for capacity estimation of IEEE 802.11 WLANs using DCF for internet applications

We provide analytical models for capacity evaluation of an infrastructure IEEE 802.11 based network carrying TCP controlled file downloads or full-duplex packet telephone calls. In each case the analytical models utilize the attempt probabilities from a well known fixed-point based saturation analysis. For TCP controlled file downloads, following Bruno et al. (In Networking '04, LNCS 2042, pp. 626-637), we model the number of wireless stations (STAs) with ACKs as a Markov renewal process embedded at packet success instants. In our work, analysis of the evolution between the embedded instants is done by using saturation analysis to provide state dependent attempt probabilities. We show that in spite of its simplicity, our model works well, by comparing various simulated quantities, such as collision probability, with values predicted from our model. Next we consider N constant bit rate VoIP calls terminating at N STAs. We model the number of STAs that have an up-link voice packet as a Markov renewal process embedded at so called channel slot boundaries. Analysis of the evolution over a channel slot is done using saturation analysis as before. We find that again the AP is the bottleneck, and the system can support (in the sense of a bound on the probability of delay exceeding a given value) a number of calls less than that at which the arrival rate into the AP exceeds the average service rate applied to the AP. Finally, we extend the analytical model for VoIP calls to determine the call capacity of an 802.11b WLAN in a situation where VoIP calls originate from two different types of coders. We consider N-1 calls originating from Type 1 codecs and N-2 calls originating from Type 2 codecs. For G711 and G729 voice coders, we show that the analytical model again provides accurate results in comparison with simulations.

Design & Implementation of IEEE 802.11s Mesh Nodes with enhanced features

This paper describes the implementation of wireless mesh nodes based on the IEEE 802.11s draft where the motivation is to build a real life mesh network. The mesh nodes developed have mesh, mesh access point and mesh portal functionalities simultaneously. The mesh nodes use different radios for mesh and access point functionalities, thus giving better service to client stations. Both reactive and proactive modes of HWMP are supported. The paper also suggests some measures to enhance the performance of the overall network by reducing the number of PREQs.