Electrochemical study of UNS S32550 super duplex stainless steel corrosion in turbulent seawater using the rotating cylinder electrode

The cathodic and anodic characteristics of freshly polished and pre-reduced UNS S32550 (ASTM A479) super duplex stainless steel in a filtered and conductivity-adjusted seawater have been investigated under controlled flow conditions. A rotating cylinder electrode was used together with both steady and non-steady-state voltammetry and a potential step current transient technique to investigate the electrode reactions in the fully characterized electrolyte. Both oxygen reduction and hydrogen evolution were highly irreversible and the material exhibited excellent passivation and repassivation kinetics. Relative corrosion rates were derived and the corrosion mechanism of the alloy was found to be completely independent of the mass-transfer effects, which can contribute to flow-induced corrosion.

Effect of sample geometry on regression rate of the melting interface for carbon steel burned in oxygen

Promoted-ignition testing on carbon steel rods of varying cross-sectional area and shape was performed in high pressure oxygen to assess the effect of sample geometry on the regression rate of the melting interface. Cylindrical and rectangular geometries and three different cross sections were tested and the regression rates of the cylinders were compared to the regression rates of the rectangular samples at test pressures around 6.9 MPa. Tests were recorded and video analysis used to determine the regression rate of the melting interface by a new method based on a drop cycle which was found to provide a good basis for statistical analysis and provide excellent agreement to the standard averaging methods used. Both geometries tested showed the typical trend of decreasing regression rate of the melting interface with increasing cross-sectional area; however, it was shown that the effect of geometry is more significant as the sample's cross sections become larger. Discussion is provided regarding the use of 3.2-mm square rods rather than 3.2-mm cylindrical rods within the standard ASTM test and any effect this may have on the observed regression rate of the melting interface.

Sedimentology of a Middle Jurassic Base-of-Slope environment, Cutri Formation, Mallorca

The Cutri Formation’s, type location, exposed in the NW of Mallorca, Spain has previously been described by Álvaro et al., (1989) and further interpreted by Abbots (1989) unpublished PhD thesis as a base-of-slope carbonate apron. Incorporating new field and laboratory analysis this paper enhances this interpretation. From this analysis, it can be shown without reasonable doubt that the Cutri Formation was deposited in a carbonate base-of-slope environment on the palaeowindward side of a Mid-Jurassic Tethyan platform. Key evidence such as laterally extensive exposures, abundant deposits of calciturbidtes and debris flows amongst hemipelagic deposits strongly support this interpretation.

Investigate the effect of antibacterial ingredients used in marine paints in sea water

In this study, consider to the mechanism of controlled depletion paint, has been made the Antifouling (A/F) paints that use these in a paint system which applied on the steel. As a first step, it is necessary to prove that the system subject to investigation does fit into the mechanisms proposed for the CDPs system. According to this, the machine was designed and built as for ASTM D5108-90, D4939-89. Specimens immersed in natural sea water and were rotating by 60 r/min rotor. Painted specimens were tested for 59 days. The main objective of this study was to investigate if new antifouling paint are less toxic than traditional paint and more efficient. For this reason, Zineb and Ziram which is an ingredient in antifouling paints, was also studied. Zineb and Ziram are known as booster biocides in A/P composition. We used the Zineb and Ziram and synthesis of these in a A/F paints. The concentration of booster biocides are 3% and 6% in paints. We use scanning electron microscopy (SEM) for evaluation of paint film. The settlement and the growth of living organism on immersed surfaces was observed during 59 days. According to reports, the growth of organism was observed for A/F paint contains, 3% Zineb after 20days,3%Ziram after 24days and 3% Zineb +Ziram after 30days. By measuring leached rate of the Zn in A/F paints, we figured out the effectiveness of booster biocides on the growth of organism, for example in the absence of booster biocides, the critical released rate for preventing biofilm for A/F paint with ZnO is 15 μg/cm2day. This despite the fact that this figure for A/F paint contain Zineb is 4 μg/cm2, Ziram is 3 μg/cm2 and Zineb +Ziram is 2 μg/cm2.