Texture evolution during annealing of large-strain deformed nanocrystalline nickel

The recrystallization behaviour of cold-rolled nanocrystalline (nc) nickel has been studied at temperatures between 573 and 1273 K using bulk texture measurements and electron back-scattered diffraction. The texture in nc nickel is different from that of its microcrystalline counterpart, consisting of a strong Goss (G) and rotated Goss (RG) components at 773 K instead of the typical cube component. The texture evolution in nc Ni has been attributed to the prior deformation textures and nucleation advantage of G and RG grains.

Thermoelectric properties of Zn doped Cu2SnSe3

Zn doped ternary compounds Cu2ZnxSn1-xSe3 (x = 0, 0.025, 0.05, 0.075) were prepared by solid state synthesis. The undoped compound showed a monoclinic crystal structure as a major phase, while the doped compounds showed a cubic crystal structure confirmed by powder XRD (X-Ray Diffraction). The surface morphology and elemental composition analysis for all the samples were studied by SEM (Scanning Electron Microscopy) and EPMA (Electron Probe Micro Analyzer), respectively. SEM micrographs of the hot pressed samples showed the presence of continuous and homogeneous grains confirming sufficient densification. Elemental composition of all the samples revealed an off-stoichiometry, which was determined by EPMA. Transport properties were measured between 324 K and 773 K. The electrical resistivity decreased up to the samples with Zn content x = 0.05 in Cu2ZnxSn1-xSe3, and slightly increased in the sample Cu2Zn0.075Sn0.925Se3. This behavior is consistent with the changes in the carrier concentration confirmed by room temperature Hall coefficient data. Temperature dependent electrical resistivity of all samples showed heavily doped semiconductor behavior. All the samples exhibit positive Seebeck coefficient (S) and Hall coefficient indicating that the majority of the carriers are holes. A linear increase in Seebeck coefficient with increase in temperature indicates the degenerate semiconductor behavior. The total thermal conductivity of the doped samples increased with a higher amount of doping, due to the increase in the carrier contribution. The total and lattice thermal conductivity of all samples showed 1/1 dependence, which points toward the dominance of phonon scattering at high temperatures. The maximum 1/TZF = 0.48 at 773 K was obtained for the sample Cu2SnSe3 due to a low thermal conductivity compared to the doped samples. (C) 2014 Elsevier B.V. All rights reserved.

Tailoring the second mode of Euler-Bernoulli beams: an analytical approach

In this paper, we study the inverse mode shape problem for an Euler-Bernoulli beam, using an analytical approach. The mass and stiffness variations are determined for a beam, having various boundary conditions, which has a prescribed polynomial second mode shape with an internal node. It is found that physically feasible rectangular cross-section beams which satisfy the inverse problem exist for a variety of boundary conditions. The effect of the location of the internal node on the mass and stiffness variations and on the deflection of the beam is studied. The derived functions are used to verify the p-version finite element code, for the cantilever boundary condition. The paper also presents the bounds on the location of the internal node, for a valid mass and stiffness variation, for any given boundary condition. The derived property variations, corresponding to a given mode shape and boundary condition, also provides a simple closed-form solution for a class of non-uniform Euler-Bernoulli beams. These closed-form solutions can also be used to check optimization algorithms proposed for modal tailoring.

Thermal Response on the Microstructure and Texture of ECAP and Cold-Rolled Pure Magnesium

This paper deals with dynamic recrystallization (DRX), static recrystallization, and grain growth phenomena of pure magnesium after equal channel angular pressing (ECAP) by route A and B-C at 523 K (250 A degrees C) followed by 80 pct cold rolling. The ECAP-deformed and the subsequently rolled samples were annealed at 373 K and 773 K (100 A degrees C and 500 A degrees C). The associated changes in the microstructure and texture were studied using electron back-scattered diffraction. ECAP produced an average grain size of 12 to 18 A mu m with B and C-2 fiber textures. Subsequent rolling led to an average grain size 8 to 10 A mu m with basal texture fiber parallel to ND. There was no noticeable increase in the average grain size on annealing at 373 K (100 A degrees C). However, significant increase in the average grain size occurred at 773 K (500 A degrees C). The occurrence of different DRX mechanisms was detected: discontinuous dynamic recrystallization was attributed to basal slip activity and continuous dynamic recovery and recrystallization to prismatic/pyramidal slip systems. Only continuous static recrystallization could be observed on annealing.

Effect of sputtering parameters on the structure, microstructure and magnetic properties of Tb-Fe films

The effect of sputtering parameters such as gas pressure and power on the structure, microstructure and magnetic properties of sputtered Tb-Fe thin films was investigated. X-ray diffraction and transmission electron microscopy studies showed that all the films were amorphous in nature irrespective of the sputtering parameters. A fine island kind of morphology was observed at low sputtering power whereas large clusters were seen at higher sputtering power. While the composition of Tb-Fe films remained constant with increasing sputtering power, the magnetic behaviour was found to change from superparamagnetic to ferromagnetic. On the other hand, the increase in argon gas pressure was found to deplete the iron concentration in Tb-Fe thin films, which in turn reduced the anisotropy and Curie temperature. Annealing of the films at 773 K did not result in any crystallization and the magnetic properties were also found to remain unchanged. (C) 2015 Elsevier B.V. All rights reserved.

High-Temperature Workability of Thixocast A356 Aluminum Alloy

The present work highlights the role of globular microstructure on the workability of A356 aluminum alloy at elevated temperature. The hot deformation behavior was studied by isothermal hot compression tests in the temperature range 573 K to 773 K (300 A degrees C to 500 A degrees C) and strain rate range of 0.001 to 10 s(-1). The flow stress data obtained from the tests were used to estimate the strain rate sensitivity and strain rate hardening. Flow stress analysis of the alloy shows that the effect of temperature on strain hardening is more significant at lower strain levels and strain rate sensitivity is independent of strain. The results also reveal that the flowability of conventionally cast alloy increases after changing the dendritic microstructure into a globular structure through semisolid processing route. Thixocast alloy exhibits lower yield strength and higher elongation at elevated temperature in comparisons to conventionally cast values. This property has an important implication toward thixo-forming at an elevated temperature. (C) The Minerals, Metals & Materials Society and ASM International 2015

Interaction of a vortex ring with a single bubble: bubble and vorticity dynamics

The interaction of a single bubble with a single vortex ring in water has been studied experimentally. Measurements of both the bubble dynamics and vorticity dynamics have been done to help understand the two-way coupled problem. The circulation strength of the vortex ring (Gamma) has been systematically varied, while keeping the bubble diameter (D-b) constant, with the bubble volume to vortex core volume ratio (V-R) also kept fixed at about 0.1. The other important parameter in the problem is a Weber number based on the vortex ring strength. (We = 0.87 rho(Gamma/2 pi a)(2)/(sigma/D-b); a = vortex core radius, sigma = surface tension), which is varied over a large range, We = 3-406. The interaction between the bubble and ring for each of the We cases broadly falls into four stages. Stage I is before capture of the bubble by the ring where the bubble is drawn into the low-pressure vortex core, while in stage II the bubble is stretched in the azimuthal direction within the ring and gradually broken up into a number of smaller bubbles. Following this, in stage III the bubble break-up is complete and the resulting smaller bubbles slowly move around the core, and finally in stage IV the bubbles escape. Apart from the effect of the ring on the bubble, the bubble is also shown to significantly affect the vortex ring, especially at low We (We similar to 3). In these low-We cases, the convection speed drops significantly compared to the base case without a bubble, while the core appears to fragment with a resultant large decrease in enstrophy by about 50 %. In the higher-We cases (We > 100), there are some differences in convection speed and enstrophy, but the effects are relatively small. The most dramatic effects of the bubble on the ring are found for thicker core rings at low We (We similar to 3) with the vortex ring almost stopping after interacting with the bubble, and the core fragmenting into two parts. The present idealized experiments exhibit many phenomena also seen in bubbly turbulent flows such as reduction in enstrophy, suppression of structures, enhancement of energy at small scales and reduction in energy at large scales. These similarities suggest that results from the present experiments can be helpful in better understanding interactions of bubbles with eddies in turbulent flows.

Inverse Polynomial Based Explicit Guidance for Lunar Soft Landing During Powered Braking

In this paper an explicit guidance law for the powered descent phase of the soft lunar landing is presented. The descent trajectory, expressed in polynomial form is fixed based on the boundary conditions imposed by the precise soft landing mission. Adapting an inverse model based approach, the guidance command is computed from the known spacecraft trajectory. The guidance formulation ensures the vertical orientation of the spacecraft during touchdown. Also a closed form relation for the final flight time is proposed. The final time is expressed as a function of initial position and velocity of the spacecraft ( at the start of descent) and also depends on the desired landing site. To ensure the fuel minimum descent the proposed explicit method is extended to optimal guidance formulation. The effectiveness of the proposed guidance laws are demonstrated with simulation results.

确定低渗透油藏启动压力梯度的三种方法

了确定低渗透油藏启动压力梯度的三种方法,重点介绍了低渗油藏试井分析确定启动压力梯度的方法和实际应用意义。给出了低渗油藏试井分析模型与常规中高渗油藏试井分析模型的对比。通过实例测试资料分析,指出了目前低渗油藏试井资料分析的一种常见错误。

Evaluación de sistemas productivos a pequeña escala de maíz y frijol utilizando indicadores de calidad de suelo en la microcuenca Las Jaguas, Ciudad Antigua 2011

Con el propósito de evaluar rendimientos y adaptabilidad de variedades mejoradas de maíz y frijol ante las frecuentes sequías y su efecto a la mejora de la calidad de suelo en la microcuenca Las Jaguas, municipio de Ciudad Antigua; se establecieron en tres fincas representativas del área un total de diez parcelas ó ensayos productivos en sitios que oscilan entre 880 y 1 980 m 2 , en época de postrera 2011. Las variedades utilizadas fueron maíz NUTRADER, maíz criollo Catacama (NB-9043), maíz criollo H-5, frijol INTA-Rojo y frijol Estelí 90 como criollo. Previo al establecimiento de los ensayos, se seleccionaron localmente un grupo de indicadores sencillos entre los cuales están: el contenido de materia orgánica en el suelo, tasa de infiltración de agua en el suelo, textura, pendiente del terreno, profundidad del suelo, piedras en la superficie, espesor orgánico, pH y fósforo disponible. Los cálculos indican que el contenido de materia orgánica comprende niveles de medio a alto; este indicador es el más importante ya que permite evaluar la calidad de suelos en vista de la influencia positiva en las propiedades y funciones básicas del suelo. Los niveles de fósforo disponible van de pobre a regular, presenta suelos muy ligeramente ácidos, textura de franco arcilloso arenosa a franco limosa arenosa; sin embargo, estos suelos tienen potencial para establecer una alternativa que permita incrementar los rendimientos de los cultivos, mediante prácticas de manejo adecuado como obras de conservación de suelos garantizando de esta manera la sostenibilidad de este recurso. Los resultados obtenidos indicaron una respuesta diferente a la aplicación de las fuentes de fertilizantes (18-46-0) y abono orgánico (lombrihumus), superando a todos los ensayos con rendimientos promedios de 1 291 kg ha -1 y 1 223 kg ha -1 , seguido por los ensayos establecidos con lombrihumus con rendimiento de 773 kg ha -1 y 427 kg ha -1 para el cultivo de frijol. En el caso del cultivo de maíz los mayores rendimientos fueron de 1 850 kg ha -1 y 1 836 kg ha -1 respectivamente, mediante la aplicación de urea y lombrihumus. El análisis económico muestra que el ensayo con fertilización lombrihumus mas 18-46-0 obtuvo los mayores beneficios económicos con C$ 1.40 por cada córdoba invertido, sin embargo, agronómicamente los mayores rendimientos se producen con la fertilización mineral y abono orgánico.

Un testigo directo de las tensiones religiosas en la Alejandría de los siglos IV y V D.C. : Páladas de Alejandría en la Antología Palatina

Abstract: Although he is the most prolific writer of the Greek Anthology, Palladas’ life is almost unknown. But, in spite of the limited biographical data, his work has fortunately been preserved in the GA. Because of his literary creation, the old times rewarded him with the nickname Μετέωρος, high, since the literary merits of a hundred poems of his authorship was recognized (others are discussed by critics). A dozen of them contains invaluable information about the political, religious and social situation in Alexandria immediately after the victory of the bishop Theophilus, Cyril’s predecessor and uncle, during the conflict between Christians and Gentiles, each sector backed up by an Alexandrian population segment (cfr. 9.528, 10.82, 10.85) . Resigned at times, constantly demanding, Palladas complains about the decline of the belief professed by him due to the increasing penetration of the new faith. Therefore, four epigrams record the conversion of the temple of Tyche into a tavern (9.180-183) and 10.90 seems to attack the doctrine of the Resurrection. When religion and politics go hand-in-hand, when religious conspiracies link up with palace intrigues, consequences are predictable: a man called Doroteo denounced him for his negative response to the new dogma, which caused him the loss of his teacher paid work. His annoyance was even greater with further sufferings, chiefly economic, and he had to sell his books (9.171 and 9.175) among other desperate decisions Forewarned about his radical bitterness against Church, it is just to make clear that he is not fully acquiescent with ancient gods and heroes. Thus, in 5.257 he questions Zeus’ ars amandi, in 9.377 refutes Tantalus’ possibility of thirst and hunger in Hades and 9.773 mischievously points out that Eros has been changed into a pan. The work begins with the selection, personal translation and comprehensive analysis of twenty two epigrams. Through such philological aid, we attempt to verify the frictions and the main perceptible factors in his poetic creation to justify his worldview, according to the pagan sentiment widespread in that time before the twilight already overwhelming of its ailing traditions

[Discurso do Deputado Emival Caiado : Sessão da Câmara dos Deputados de 28 de agosto de 1957]

Discussão do Projeto nº 1.773-A, de 1956, que fixa a data para a mudança da Capital Federal. Reafirmação dos argumentos favoráveis à mudança da Capital Federal do ponto de vista adinistrativo, social, político e econômico. Refutação dos argumentos de que a mudança da capital trará prejuízos insanáveis à cidade do Rio de Janeiro.