New static 3-step distance relay

A new static 3-step distance relay based on the principle of multi-input phase comparison is described in the paper. Design principles and typical discriminating and logic circuits are described for the new relaying system. The relaying system uses semiconductor circuits throughout and features high speed and good performance. The comparator model, which effects multi-input phase comparison, has been devised to provide reliable pickup for closein faults, and to achieve an improved polar characteristic in the complex- impedance plane, which fits around only the fault area of a transmission line. Operating time of the relay is less than 1 cycle for unbalanced faults, and less than a halfcycle for 3-phase faults. Protective circuits have also been added to detect power swing and to block tripping for a predetermined number of power-swing cycles. The operating characteristics of the relay, as expressed by accuracy/range charts, are presented.

Matrix Processors Using p-adic Arithmetic for Exact Linear Computations

A unique code (called Hensel's code) is derived for a rational number by truncating its infinite p-adic expansion. The four basic arithmetic algorithms for these codes are described and their application to rational matrix computations is demonstrated by solving a system of linear equations exactly, using the Gaussian elimination procedure.

On the mechanism of plastic flow at 86°k in quenched and aged aluminum

The plastic flow of quenched aluminium at 86°K was investigated by ‘differential-stress’ creep tests in order to evaluate the rate-controlling mechanism in as-quenched and fully aged states. The experimental values of activation volume (4·3 × 10−21 cm3 for as-quenched and 5·5×l0−21cm3 for fully aged) and the total energy for thermal activation process (0·4 ev for both) are in accordance with the jog hardening and loop hardening mechanisms in quenched and fully aged states respectively.

Affinity of a galactose-specific legume lectin from Dolichos lablab to adenine revealed by X-ray cystallography

Crystal structure analysis of a galactose-specific lectin from a leguminous food crop Dolichos lablab (Indian lablab beans) has been carried out to obtain insights into its quaternary association and lectin-carbohydrate interactions. The analysis led to the identification of adenine binding sites at the dimeric interfaces of the heterotetrameric lectin. Structural details of similar adenine binding were reported in only one legume lectin, Dolichos biflorus, before this study. Here, we present the structure of the galactose-binding D. lablab lectin at different pH values in the native form and in complex with galactose and adenine. This first structure report on this lectin also provides a high resolution atomic view of legume lectin-adenine interactions. The tetramer has two canonical and two DB58-like interfaces. The binding of adenine, a non-carbohydrate ligand, is found to occur at four hydrophobic sites at the core of the tetramer at the DB58-like dimeric interfaces and does not interfere with the carbohydrate-binding site. To support the crystallographic observations, the adenine binding was further quantified by carrying out isothermal calorimetric titration. By this method, we not only estimated the affinity of the lectin to adenine but also showed that adenine binds with negative cooperativity in solution.

Authentication using finger Knuckle prints

Automated security is one of the major concerns of modern times. Secure and reliable authentication systems are in great demand. A biometric trait like the finger knuckle print (FKP) of a person is unique and secure. Finger knuckle print is a novel biometric trait and is not explored much for real-time implementation. In this paper, three different algorithms have been proposed based on this trait. The first approach uses Radon transform for feature extraction. Two levels of security are provided here and are based on eigenvalues and the peak points of the Radon graph. In the second approach, Gabor wavelet transform is used for extracting the features. Again, two levels of security are provided based on magnitude values of Gabor wavelet and the peak points of Gabor wavelet graph. The third approach is intended to authenticate a person even if there is a damage in finger knuckle position due to injury. The FKP image is divided into modules and module-wise feature matching is done for authentication. Performance of these algorithms was found to be much better than very few existing works. Moreover, the algorithms are designed so as to implement in real-time system with minimal changes.

Effect of Heat Pipe Figure of Merit on an Evaporating Thin Film

The performance of a two-phase heat transport device such as the loop heat pipe is influenced by the evaporative heat transfer coefficient in the evaporator. From previous experiments with loop heat pipes, it has been observed that fluids with a high heat pipe figure of merit have a high heat transfer coefficient. Considering an evaporating extended thin film, this paper theoretically corroborates this experimental observation by deriving a direct link between the evaporative heat flux at the interface and the fluid figures of merit (namely interline heat flow parameter and heat pipe figure of merit) in the thin film. Numerical experiments with different working fluids clearly show that a fluid with high figure of merit also has a high cumulative heat transfer in the microregion encompassing the evaporating thin film. Thus, a loop heat pipe or heat pipe that uses a working fluid with a high interline heat flow parameter and heat pipe figure of merit will lead to a high evaporative heat transfer coefficient.

Microstructure dependent elastic modulus variation in NiTi shape memory alloy

Modulus variation of NiTi shape memory alloy has been investigated at microstructural level through nano dynamical mechanical analysis and compared with bulk experimental measurements. The differences between the modulus values at the macro and micro level as well as within the micro level are discussed and the corresponding variations have been explained based on the crystal structure, orientation and misorientation. The experimental results confirm a higher modulus value for the martensite phase that is in agreement with the theoretical predictions. (C) 2015 Elsevier B. V. All rights reserved.

GHG footprint of major cities in India

Concentration of greenhouse gases (GHG) in the atmosphere has been increasing rapidly during the last century due to ever increasing anthropogenic activities resulting in significant increases in the temperature of the Earth causing global warming. Major sources of GHG are forests (due to human induced land cover changes leading to deforestation), power generation (burning of fossil fuels), transportation (burning fossil fuel), agriculture (livestock, farming, rice cultivation and burning of crop residues), water bodies (wetlands), industry and urban activities (building, construction, transport, solid and liquid waste). Aggregation of GHG (CO2 and non-CO2 gases), in terms of Carbon dioxide equivalent (CO(2)e), indicate the GHG footprint. GHG footprint is thus a measure of the impact of human activities on the environment in terms of the amount of greenhouse gases produced. This study focuses on accounting of the amount of three important greenhouses gases namely carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) and thereby developing GHG footprint of the major cities in India. National GHG inventories have been used for quantification of sector-wise greenhouse gas emissions. Country specific emission factors are used where all the emission factors are available. Default emission factors from IPCC guidelines are used when there are no country specific emission factors. Emission of each greenhouse gas is estimated by multiplying fuel consumption by the corresponding emission factor. The current study estimates GHG footprint or GHG emissions (in terms of CO2 equivalent) for Indian major cities and explores the linkages with the population and GDP. GHG footprint (Aggregation of Carbon dioxide equivalent emissions of GHG's) of Delhi, Greater Mumbai, Kolkata, Chennai, Greater Bangalore, Hyderabad and Ahmedabad are found to be 38,633.2 Gg, 22,783.08 Gg, 14,812.10 Gg, 22,090.55 Gg, 19,796.5 Gg, 13,734.59 Gg and 91,24.45 Gg CO2 eq., respectively. The major contributors sectors are transportation sector (contributing 32%, 17.4%, 13.3%, 19.5%, 43.5%, 56.86% and 25%), domestic sector (contributing 30.26%, 37.2%, 42.78%, 39%, 21.6%, 17.05% and 27.9%) and industrial sector (contributing 7.9%, 7.9%, 17.66%, 20.25%, 1231%, 11.38% and 22.41%) of the total emissions in Delhi, Greater Mumbai, Kolkata, Chennai, Greater Bangalore, Hyderabad and Ahmedabad, respectively. Chennai emits 4.79 t of CO2 equivalent emissions per capita, the highest among all the cities followed by Kolkata which emits 3.29 t of CO2 equivalent emissions per capita. Also Chennai emits the highest CO2 equivalent emissions per GDP (2.55 t CO2 eq./Lakh Rs.) followed by Greater Bangalore which emits 2.18 t CO2 eq./Lakh Rs. (C) 2015 Elsevier Ltd. All rights reserved.

具有单元分裂功能的间断有限元方法

介绍一种能够模拟材料开裂过程的有限元方法,该方法引入单元分裂和界面分离技术,结合具体的破坏准则,模拟材料变形中的破坏,同时还可以方便地处理材料中任意分布的界面结构.以三点弯曲实验为例,通过数值模拟结果和实验数据的比较,验证了该方法的适用性.

Squeeze-film Effects in MEMS Devices with Perforated Plates for Small Amplitude Vibration

Squeeze-film effects of perforated plates for small amplitude vibration are analyzed through modified Reynolds equation (MRE). The analytical analysis reckons in most important influential factors: compressibility of the air, border effects, and the resistance caused by vertical air flow passing through perforated holes. It is found that consideration of air compressibility is necessary for high operating frequency and small ratio of the plate width to the attenuation length. The analytical results presented in this paper agree with ANSYS simulation results better than that under the air incompressibility assumption. The analytical analysis can be used to estimate the squeeze-film effects causing damping and stiffness added to the system. Since the value of Reynolds number involved in this paper is low (< 1), inertial effects are neglected.

Evaluación de la producción de biomasa de dos cultivares de Panicum virgatum (L.) durante el período de implantación y el primer año de producción

La Argentina vive, desde hace unos años, un claro desplazamiento de la ganadería hacia zonas marginales, en las cuales imperan condiciones edáficas y climáticas que son generadoras de estrés para una amplia cantidad de forrajeras utilizadas. El objetivo del presente estudio fue evaluar el rendimiento de Panicum virgatum (L.). Esta especie forrajera de metabolismo C4 fue descrita como tolerante a condiciones marginales de crecimiento. Fueron evaluados los cvs. Shawnee y Trailblazer. El experimento se condujo en dos ambientes: I) en el predio perteneciente a la Facultad de Ciencias Agrarias de la Universidad Católica Argentina (Lat.34°34´S, 58°26´O) en el cual se evaluó el rendimiento de ambas variedades sembradas a una distancia de 17,5 cm entre hileras y II) en Luján (Buenos Aires, Lat.34°32´S, 59°16´O) en un suelo Argiudol típico, evaluando solamente al cv. Shawnee a dos distintos distanciamientos entre hileras (17,5 y 35 cm). Ambos sitios experimentales se prepararon según un sistema de labranza convencional. Las siembras se efectuaron los días 3 y 5 de octubre de 2008 (ambiente 1 y 2 respectivamente) en forma manual y con un distanciamiento dentro de la hilera de 5cm y una profundidad de 1cm. El arreglo experimental consistió en un DCA con tres repeticiones. Los datos obtenidos se analizaron mediante un Análisis de la Varianza. Se tomó como criterio de defoliación una altura del follaje de 60cm y dejando una altura remanente de 15cm luego del corte En el ambiente 1, el rendimiento acumulado no difirió estadísticamente entre los genotipos estudiados en las dos campañas evaluadas. Durante el primer año, la producción (expresada en kg MS ha-1 ± EEM) del cv. Shawnee fue de 6.293,33 ± 673,42 mientras que el cv. Trailblazer produjo 5.072,38 ± 1.011,85. En cambio, durante el segundo año se observó un marcado incremento en la producción acumulada registrándose valores de 10.590,48 ± 638,31 y 8.857,14 ± 2187,41 para los cv Trailblazer y Shawnee respectivamente. En el ambiente 2, no se observaron diferencias en el rendimiento del cultivo sembrado a 17,5cm o 35 cm de distancia entre hileras. En efecto, con una separación de 17.5 cm se registró una producción de 8.302,85 ± 342,92 y 26.095,24 ± 3780,99 (año 1 y 2 respectivamente) mientras que a 35 cm se observaron 6.054,28± 1.216,01 y 29.428,57± 5.735,67 (año 1 y 2 respectivamente).Se observó la formación de estructuras reproductivas en ambos genotipos demostrando la adaptabilidad de esta especie a nuestra latitud. Los resultados presentados señalan la utilidad de continuar la evaluación de esta especie incluyendo su evaluación en ambientes donde la misma sea capaz de expresar la tolerancia a los factores abióticos generadores de estrés y su respuesta a otras variables de manejo agronómico.

Aglutininas para once serotipos de leptospira en bovinos de los departamentos de Boaco, Managua, Matagalpa y Granada

Se recolectaron muestras de sangre de 633 bovinos de los departamentos de Boaco, Managua, Matagalpa y Granada. Se examino en ellas las presencia de aglutininas para la Leptospirosis por medio de la prueba de aglutinación microscópica. Se encotro que en Boaco y Matagalpa prevalece L. pomona, en Managua L. canicola y L. hyos en Granada. Se encontraron los siguientes porcentajes de infeccion; En Managua 24.66%, en Granada 11.03%, en Boaco 9.37% y en Matagalpa 7.69%.

充液腔体旋转运动的稳定性理论

本文对于具有一个定点,并充满粘性液体的腔,在重力场中绕惯性主轴的平衡旋转运动,采用Movchan直接法,就尽可能多样的Movchan距离,推广了和的稳定性定理,并对尽可能全面的腔参数(包括临界情况在内)给出了具体的稳定性结论。

双套管密相气力输运过程的数值模拟和能耗分析

基于计算流体力学理论,提出一种可用于预测双套管密相气力输送系统能耗的新方法.与以往依靠经验的计算方法不同,本工作将输送管道分为起始段与充分发展段两部分,分别进行详细的计算流体力学模拟后汇总得出整个系统的总能耗.压力梯度为750 Pa/m的情况下,计算所得物料输送速率为10 t/h,耗气量为290 m~3/h,实验所得物料输送速率为8.0 t/h,耗气量240 m~3/h,证明本数模方法是可靠的.