Permeability measurements on sheared and unsheared samples from different IODP Holes of Leg 316 and from IODP Hole 315-C0001E and ODP Hole 190-1174B

At subduction zones, the permeability of major fault zones influences pore pressure generation, controls fluid flow pathways and rates, and affects fault slip behavior and mechanical strength by mediating effective normal stress. Therefore, there is a need for detailed and systematic permeability measurements of natural materials from fault systems, particularly measurements that allow direct comparison between the permeability of sheared and unsheared samples from the same host rock or sediment. We conducted laboratory experiments to compare the permeability of sheared and uniaxially consolidated (unsheared) marine sediments sampled during IODP Expedition 316 and ODP Leg 190 to the Nankai Trough offshore Japan. These samples were retrieved from: (1) The décollement zone and incoming trench fill offshore Shikoku Island (the Muroto transect); (2) Slope sediments sampled offshore SW Honshu (the Kumano transect) ~ 25 km landward of the trench, including material overriden by a major out-of-sequence thrust fault, termed the "megasplay"; and (3) A region of diffuse thrust faulting near the toe of the accretionary prism along the Kumano transect. Our results show that shearing reduces fault-normal permeability by up to 1 order of magnitude, and this reduction is largest for shallow (< 500 mbsf) samples. Shearing-induced permeability reduction is smaller in samples from greater depth, where pre-existing fabric from compaction and lithification may be better developed. Our results indicate that localized shearing in fault zones should result in heterogeneous permeability in the uppermost few kilometers in accretionary prisms, which favors both the trapping of fluids beneath and within major faults, and the channeling of flow parallel to fault structure. These low permeabilities promote the development of elevated pore fluid pressures during accretion and underthrusting, and will also facilitate dynamic hydrologic processes within shear zones including dilatancy hardening and thermal pressurization.

n-Alkane, fatty acid and hopanoic acid concentrations of ODP Site 190-1178 samples

Ocean Drilling Program (ODP) Leg 190 was programmed to investigate deformational, diagenetic, and hydrologic processes and their interactions in the Nankai Trough accretionary prism. Site 1178 is the northernmost site in the Muroto Transect. Slope sediments and the underlying landward-dipping reflector zone were successfully cored. Temperature measurements and Cl concentrations in pore water indirectly indicate the presence of gas hydrate between 120 and 400 meters below seafloor (mbsf) at Site 1178, with the highest concentrations between 150 and 200 mbsf (Shipboard Scientific Party, 2001, doi:10.2973/odp.proc.ir.190.109.2001). Sedimentary structures show a broad range of deformation structures rich in fractures, suggesting active fluid circulation in the Nankai Trough prism. One of the objectives of Leg 190 was to clarify the interplay of various fundamental processes taking place in the Nankai Trough accretionary prism. Bacteria or prokaryotes in deep subsurface sediment play an important role for material transformation and circulation in an accretionary prism. Significant amounts of bacteria are detected in many of the samples examined (Shipboard Scientific Party, 2001, doi:10.2973/odp.proc.ir.190.109.2001). The type of organic matter in sediments is an important factor related to bacterial activity. To assist investigations on material circulation in deep subsurface sediments, the samples from Site 1178 were analyzed for geolipids (extractable organic matter). The basic data set is preliminarily compiled in the present report to show the types of organic matter and their concentrations in sediments from Site 1178.

Mineral composition of sediments from ODP Leg 190 sites and DSDP Hole 31-297

This data report documents the acquisition of two new sets of normalization factors for semiquantitative X-ray diffraction analyses. One set of factors is for bulk sediment powders, and the other applies to oriented aggregates of clay-sized fractions (<2 µm). We analyzed mixtures of standard minerals with known weight percentages of each component and solved for the normalization factors using matrix singular value decomposition. The components in bulk powders include total clay minerals (a mixture of smectite, illite, and chlorite), quartz, plagioclase, and calcite. For clay-sized fractions, the minerals are smectite, illite, chlorite, and quartz. We tested the utility of the method by analyzing natural mudstone specimens from Site 297 of the Deep Sea Drilling Project, which is located in the Shikoku Basin south of Site 1177 of the Ocean Drilling Program (Ashizuri transect).