The Design and Implementation of a Power Management Feature to a Configuration Management System

Green IT is a term that covers various tasks and concepts that are related to reducing the environmental impact of IT. At enterprise level, Green IT has significant potential to generate sustainable cost savings: the total amount of devices is growing and electricity prices are rising. The lifecycle of a computer can be made more environmentally sustainable using Green IT, e.g. by using energy efficient components and by implementing device power management. The challenge using power management at enterprise level is how to measure and follow-up the impact of power management policies? During the thesis a power management feature was developed to a configuration management system. The feature can be used to automatically power down and power on PCs using a pre-defined schedule and to estimate the total power usage of devices. Measurements indicate that using the feature the device power consumption can be monitored quite precisely and the power consumption can be reduced, which generates electricity cost savings and reduces the environmental impact of IT.

SOCIAL MEDIA IN INTERNATIONAL BRAND COMMUNICATION OF SMES - A multiple case study of small Finnish design-intensive companies

Social media is a rather new phenomenon which has revolutionised the world of online communication. However, academic research on how companies can benefit from social media is lacking. The research objective of this thesis was to examine the use of social media in international brand communication of small Finnish design-intensive companies. Therefore, this research contributes also to the research gap in SME branding. The focus was on communication targeted at consumers. The research was carried out as a mixed methods research employing the questionnaire and multiple case study methods. The questionnaire was used to gather preliminary information on Finnish design-intensive companies and to provide an eligible list of companies for deeper examination. Then, four case companies were studied in more depth. The empirical evidence of the case companies was mainly gathered through theme interviews. The results of the questionnaire shed light on the internationalisation of small Finnish designintensive companies. On average, the companies had internationalised rather quickly after they had been founded. However, the share of exports was rather low in most of the companies. The results revealed also that social media was already used widely in the exporting companies and the use can be expected to grow in future. The findings of the multiple case study suggest that branding activities in small Finnish designintensive companies are constrained by limited resources and skills. In addition, the branding activities are strongly guided by the vision and values of the entrepreneur(s) rather than extensive marketing research. The brand structure was simple in all case companies and they aimed at having a standardised brand image across markets. However, all case companies had faced a need for some adaptation of their international brand communication. Internationally important brand communication channels were international fairs, the internet, word-of-mouth and social media. Social media offered a cost-effective brand communication channel for the case companies. It was used for various purposes, such as creating brand awareness and affecting how the brand is perceived. The entrepreneurs found the use of social media to be rather easy and the case companies had not faced any major challenges. However, the companies had recognised that communication in social media requires consistency and planning. The planning was rather informal and stayed on a general level. Overall, the utilisation of social media in the case companies was limited by a lack of resources. It seemed to affect especially the follow-up of brand communication in social media which stayed rather superficial.

Design and implementation of robot gripper interface

This thesis presents a design for an asynchronous interface to Robotiq adaptive gripper s-model. Designed interface is a communication layer that works on top of modbus layer. The design contains function definitions, finite state machine and exceptions. The design was not fully implemented but enough was so that it can be used. The implementation was done with c++ in linux environment. Additionally to the implementation a simple demo program was made to show the interface is used. Also grippers closing speed and force were measured. There is also a brief introduction into robotics and robot grasping.

Design and Control of Permanent Magnet Synchronous Machine for Hybrid Electric Vehicle

This master’s thesis mainly focuses on the design requirements of an Electric drive for Hybrid car application and its control strategy to achieve a wide speed range. It also emphasises how the control and performance requirements are transformed into its design variables. A parallel hybrid topology is considered where an IC engine and an electric drive share a common crank shaft. A permanent magnet synchronous machine (PMSM) is used as an electric drive machine. Performance requirements are converted into Machine design variables using the vector model of PMSM. Main dimensions of the machine are arrived using analytical approach and Finite Element Analysis (FEA) is used to verify the design and performance. Vector control algorithm was used to control the machine. The control algorithm was tested in a low power PMSM using an embedded controller. A prototype of 10 kW PMSM was built according to the design values. The prototype was tested in the laboratory using a high power converter. Tests were carried out to verify different operating modes. The results were in agreement with the calculations.

Software for design of experiments and response modelling of cake filtration applications

Filtration is a widely used unit operation in chemical engineering. The huge variation in the properties of materials to be ltered makes the study of ltration a challenging task. One of the objectives of this thesis was to show that conventional ltration theories are di cult to use when the system to be modelled contains all of the stages and features that are present in a complete solid/liquid separation process. Furthermore, most of the ltration theories require experimental work to be performed in order to obtain critical parameters required by the theoretical models. Creating a good overall understanding of how the variables a ect the nal product in ltration is somewhat impossible on a purely theoretical basis. The complexity of solid/liquid separation processes require experimental work and when tests are needed, it is advisable to use experimental design techniques so that the goals can be achieved. The statistical design of experiments provides the necessary tools for recognising the e ects of variables. It also helps to perform experimental work more economically. Design of experiments is a prerequisite for creating empirical models that can describe how the measured response is related to the changes in the values of the variable. A software package was developed that provides a ltration practitioner with experimental designs and calculates the parameters for linear regression models, along with the graphical representation of the responses. The developed software consists of two software modules. These modules are LTDoE and LTRead. The LTDoE module is used to create experimental designs for di erent lter types. The lter types considered in the software are automatic vertical pressure lter, double-sided vertical pressure lter, horizontal membrane lter press, vacuum belt lter and ceramic capillary action disc lter. It is also possible to create experimental designs for those cases where the variables are totally user de ned, say for a customized ltration cycle or di erent piece of equipment. The LTRead-module is used to read the experimental data gathered from the experiments, to analyse the data and to create models for each of the measured responses. Introducing the structure of the software more in detail and showing some of the practical applications is the main part of this thesis. This approach to the study of cake ltration processes, as presented in this thesis, has been shown to have good practical value when making ltration tests.