A modified nominal stress method for fatigue assessment of steel plates with thermally cut edges

Thermal cutting methods, are commonly used in the manufacture of metal parts. Thermal cutting processes separate materials by using heat. The process can be done with or without a stream of cutting oxygen. Common processes are Oxygen, plasma and laser cutting. It depends on the application and material which cutting method is used. Numerically-controlled thermal cutting is a cost-effective way of prefabricating components. One design aim is to minimize the number of work steps in order to increase competitiveness. This has resulted in the holes and openings in plate parts manufactured today being made using thermal cutting methods. This is a problem from the fatigue life perspective because there is local detail in the as-welded state that causes a rise in stress in a local area of the plate. In a case where the static utilization of a net section is full used, the calculated linear local stresses and stress ranges are often over 2 times the material yield strength. The shakedown criteria are exceeded. Fatigue life assessment of flame-cut details is commonly based on the nominal stress method. For welded details, design standards and instructions provide more accurate and flexible methods, e.g. a hot-spot method, but these methods are not universally applied to flame cut edges. Some of the fatigue tests of flame cut edges in the laboratory indicated that fatigue life estimations based on the standard nominal stress method can give quite a conservative fatigue life estimate in cases where a high notch factor was present. This is an undesirable phenomenon and it limits the potential for minimizing structure size and total costs. A new calculation method is introduced to improve the accuracy of the theoretical fatigue life prediction method of a flame cut edge with a high stress concentration factor. Simple equations were derived by using laboratory fatigue test results, which are published in this work. The proposed method is called the modified FAT method (FATmod). The method takes into account the residual stress state, surface quality, material strength class and true stress ratio in the critical place.

Physiological quality of wheat seeds submitted to saline stress

The objective of this experiment was to determine the influence of different salt levels (zero, 15, 30, 45 and 60mM NaCl) on seed physiological quality of two wheat cultivars (BRS 177 and BRS 179). SUMMARIZE METHODOLOGY. The results allow the following conclusions: the physiological quality (germination and vigor) of wheat seeds, cultivars BRS 179 and BRS 177, decrease with the increase of the salinity. The wheat seeds cv. BRS 179 performs better than BRS 177, mainly in higher salt concentrations (³ 45mM of NaCl). The electric conductivity of wheat seeds increases in function of the increment of the saline concentrations.

Physiological quality of barley seeds submitted to saline stress

The objective of the experiments was to determine the influence of the effects of different salt levels (zero, 15, 30, 45 and 60mM NaCl) on the physiological quality of seeds of two barley cultivars (BRS 195 and AF 98067). Assays were conducted to evaluate salt stress on germination and vigor. The germination and germination rate of the barley seeds decreased as salt levels increased, reducing the seed viability and vigor. The salinity affected the membrane integrity, mainly in AF 98067 that showed more sensitivity to salt stress.

Germination, initial growth and cotyledon protein content of bean cultivars under salinity stress

Excess salts in the root zone inhibit water uptake by plants, affect nutrient uptake and may result in toxicities due to individual salts in the soil solution. Excess exchangeable sodium in the soil may destroy the soil structure to a point where water penetration and root aeration become impossible. Sodium is also toxic to many plants. Beans (Phaseolus vulgaris L.) are consumed as protein source in northeastern Brazil, although little is known about common bean cultivar tolerance to salinity. The germination of bean cultivars under salt stress was studied. The cultivars 'Carioca' and 'Mulatinho' were submitted to germination test in a germinator at 25ºC, at the Seed Analysis Laboratory of the Brazilian Agricultural Research Corporation unit in the Semi- Arid region (Embrapa Semi Árido), Petrolina, Pernambuco State. These seeds were germinated on "germitest" papers imbibed in distilled water or in 10, 50, 100 e 200 mol.m-3sodium chloride (NaCl) solutions. At the first and second counts of the germination test, normal seedlings were counted, measured, weighed and dried, supplying data for vigor, total germination, fresh matter weight and dry matter weight and seedlings length. Total protein was quantified in cotyledons at 3, 6 and 9 days after sowing. The results indicated that the NaCl content influenced seed germination and concentrations above 50 mol.m-3 decreased germination and seedling growth.

Thermal and moisture content effects on storability and seed dormancy releasing on Brachiaria brizantha cultivars

Brachiaria species normally show a double seed dormancy mechanism, mainly on fresh-harvested seeds, leading to germination percentages lower than those of viability detected by tetrazolium test (TZ) and causing problems as to storage, trading and seed inspection activities. The adoption of the methodology to detect the constants of the viability equation (high storage temperatures and fixed moisture contents) made feasible in this research to isolate the effects of 40, 50 and 65°C on B. brizantha cultivars Marandu, Mulato 1 and Mulato 2 seed dormancy releasing, after storage with moisture contents ranging from 1.9 and 17.8%. Seed samples presented high dormancy levels, detected by TZ and it was complete and partially released by chemical scarification and accelerated ageing test, respectively. No statistical differences were observed as to the speed of germination (T50); however, differences among cultivars were detected as to number of seed per gram. Sorption and desorption isotherm curves were similar for the cultivars. Seed dormancy releasing was better achieved at 40 and 50°C with mc ranging from 7.6 to 10.8%. The temperature of 50°C appears to be adequate for seed dormancy releasing in all mc analyzed. No significant seed dormancy releasing result was observed at 65°C. The cultivar Marandu presented the highest storability throughout the experiment.

Response of soybean genotypes to the expression of green seed under temperature and water stresses

Soybeans grown under water stress associated with high temperatures during seed maturation and pre-harvest may produce green seed (GS) with expressive reduction in seed quality. The objectives of this study were to evaluate the response of different soybean cultivars grown under these stressful conditions regarding their susceptibility to GS production and to determine the chlorophyll retention levels and the chlorophyllase activity in the seeds. Seeds of four soybean cultivars [BRS 133, CD 206, MG/BR 46 (Conquista) and BRSMG 251 (Robusta)] were grown under greenhouse conditions until R5.5. At R6, the plants were transferred to phytotrons under temperature stress (from 28ºC to 36ºC) and with water stresses of 10% gravimetric moisture, no water and normal supply. Seeds were harvested at R9 when the percentage of GS and weight of 100 seeds were determined. The contents of a, b and total chlorophylls and the chlorophyllase activity were also determined. The expression of GS production under these conditions varied among cultivars: Conquista and Robusta were considered more susceptible to the production of GS compared to 'BRS 133' and 'CD 206'. These cultivars produced lower GS levels, lower chlorophyll retention and higher chlorophyllase activity compared to Robusta and Conquista. Soybean plants submitted to water and temperature stresses produced high levels of GS, which were small, light and had high chlorophyll contents and low chlorophyllase activity. The contents of a, b and total chlorophylls in GS were inversely proportional to the chlorophyllase activity.

Incidence of green soybean seeds as a function of environmental stresses during seed maturation

Hot and dry weather conditions during soybean [Glycine max (L.) Merrill] seed maturation can cause forced maturation of the seed, resulting in the production of high levels of green seed, which may be detrimental to seed germination. These stressful conditions were imposed on soybean plants during seed maturation to investigate the production of green seeds and seed quality. Plants of the CD 206 cultivar were grown in a greenhouse until the R5.5 growing stage and then transferred to phytotrons at R6 and R7.2 for stress induction. Plants were subjected to two temperature regimes, high (28ºC to 36ºC) and normal (19ºC to 26ºC), and four soil water availability conditions, control (adequate water supply), 30% gravimetric moisture (GM), 20% GM and no water supply. Seed were harvested at R9. Green seed percentages and 100-seed weights from the lower, middle and upper thirds of each plant were determined. Seed quality was assessed by germination, tetrazolium (viability and vigor) and electrical conductivity tests. Occurrence of green seed varied from 9% to 86%, depending on the severity of the stresses imposed. High temperature, coupled with no water supply at R6, resulted in a pronounced occurrence of green seeds. There was no difference in the percentage of green seeds among the plant segments. Seed quality was negatively affected by the incidence of green seeds. A procedure for screening soybean genotypes in a phytotron for their tolerance and/or susceptibility to the production of green seeds was developed.

Partial characterization of genes from the embryonic axis of Melanoxylon brauna Schott. (Leguminosae-Caesalpinioideae) seeds

The objective of this study was to partially characterize some genes involved in the desiccation tolerance of the embryonic axis of Melanoxylon brauna seeds subjected, or not, to oven fast-drying. Seeds were initially dried rapidly in an oven at 40 ºC, 50 ºC, 60 ºC, 70 ºC, and 80 °C, for 24, 48 and 72 h and then subjected to germination tests and moisture content determination. Degenerate primers were designed for 19 genes. The CDNA was used as a template for PCR amplifications using the degenerate primers, and the PCR products obtained were purified, cloned and sequenced. The seeds showed a gradual reduction in percent germination with increasing temperature and drying time. Nucleotide sequences of the cloned fragments related to genes CAT1, SPS1, Abi5, Transk and PM25 were obtained. The similarity analysis with the sequences deposited in databases revealed similarities with genes CAT1, SPS1, Transk and PM25 from other plant species. The nucleotide sequences obtained from the respective genes will be used for designing specific primers for gene expression analyses during seed germination in order to understand the causes for loss of physiological quality of Melanoxylon brauna seeds.

Plantability and moisture content of naked and pelleted seeds of supersweet (Sh2) corn during cold storage conditions

The supersweet (Sh2) corn seeds have a thin tegument and an irregular shape, which hinder the sowing procedure. As a function of those factors, the significance of using the pelleting process to improve sowing and standardize the stand of plants in the field without the need of thinning within the row is emphasized. Although this technique has already been known for many years, little has been studied on the effect of such procedure on the plantability and on the moisture content of the supersweet corn seeds. Therefore, this research work aimed at evaluating the effects of pelleting on the moisture content of the seeds along the storing process, on the occurrence of gaps on seed deposition and on the dropping of double seeds, with the aid of a testing seeder. Other physical attributes of seeds and pellets were also evaluated through tests of fragmentation, screen retention, mass of a thousand seeds and apparent volume. Results have shown an increase on the mass and on the volume of the pelleted seeds that presented highly resistance to cracks and breaking. The pelleting was efficient on the reduction of gaps and on the deposition of double seeds at sowing, thus providing highly satisfactory results for these attributes. An increase on the seed moisture content was also observed as a function of storage with a significant reduction on this factor after the pelleting procedure. Results allow concluding that the pelleting process reduces seed moisture content and improves plantability, positively affecting the efficiency of the sowing process.