Effect of plant row spacing and herbicide use on weed aboveground biomass and corn grain yield

The use of narrow plant spacing in corn (Zea mays) has been suggested as a technological alternative to obtain grain yield increases, due to a better use of resources. The regular pattern could diminish intraspecific competition while favoring interspecific competition with weeds. The objective of this study was to analyze the effect of corn row spacing on weed aboveground biomass and corn grain yield. Field experiments were conducted during 2002/2003 and 2003/2004 growing seasons. Three corn hybrids with two-row width (0.70 and 0.35 m) were tested. A greater photosynthetic photon flux density (PPFD) interception with a lower weed aboveground dry matter in narrow row arrangement was obtained. Corn grain yield was greater in the narrow row arrangement than in the wide row spacing. This increase in grain yield was related to a better resource use that allows for a reduced interspecific competition. The use of reduced spatial arrangement appeared to be an interesting alternative to increase both the grain yield potential and corn suppressive ability against weeds in corn dryland production systems.

Towards optimal fractionation of lignocellulosic biomass using switchable ionic liquids

En ny familj av reversibla (switchable) joniska vätskor (SIL) innehållande 1,8-diazobicyklo-[5.4.0]-undek-7-en (DBU), en molekyl innehållande en eller flera hydroxyl- grupper (t.ex. glycerol) och en sur gas (CO2, SO2) syntetiserades via en enkel procedur samt karakteriserades. [DBU][karbonat] eller [sulfonat] bildades ur en respektive icke-jonisk blandning av en molekylär, organisk polyol (eller ennan molekyl innehållande en OH-grupp) och en amidinbas under bubblandet av en sur gas. Därtill kunde den joniska vätskan omvandlas tillbaka till sina beståndsdelar med hjälp av att upphetta och/eller bubbla en inert gas såsom kväve genom vätskan. SIL- strukturerna kartlades med bl.a. NMR- och FTIR- spektroskopi. Omvandlingen från lågpolära (molekylära) vätskor till högpolära joniska vätskor (SIL) bekräftades även genom att observera förändringar i deras fysikaliska egenskaper, såsom viskositet och färg. Nedbrytningstemperaturerna hos SILs bestämdes med hjälp av termogravimetrisk analys (TGA) som antydde att nedbrytningstemperaturen hos de syntetiserade föreningarna log mellan 50 och 200oC. De nya joniska vätskorna uppvisade högre nedbrytningstemperaturer jämfört med i litteraturen tidigare förekommande exempel och kunde därför tillämpas på flera ändamål. Därtill, reversibla (switchable) joniska vätskor uppbyggda av bl.a. alkoholer, antingen hexanol eller butanol, och CO2 samt en amidin (DBU) användes vid upplösning och fraktionering av ved. Joniska vätskor syntetiserade ur glycerol och sura gaser tillsammans med amidiner användes även för fraktionering av andra lignocellulosor såsom färsk björk (Betula pendula). Björkflis utsattes för behandling, för en period på en till fem dagar vid 100oC och under atmosfäriskt tryck. Alla syntetiserade joniska vätskor visade sig vara relativt neutrala i avseende på upplösning och avlägsnandet av lignin. Slutligen, optimala fraktioneringprocessbetingelser för ved med reversibla joniska vätskor kartlades. Fraktionering av vedbiomassa med dessa joniska vätskor uppvisade sig att vara en selektiv och effektiv metod för extraktion av olika komponenter från lignocellulosa. Den olösta fraktionen hos en vedflis, närmast cellulosa, fibrillerades. -------------------------------------------------------------------------------------------------------------------- Tässä työssä kehitettiin perhe uuden tyyppisiä, reversiibeleitä (switchable) ioninesteitä ( SIL ) joka koostuvat orgaanisesta super-emäksestä kuten 1,8- diatsabisyklo [ 5.4.0] undek- 7-eeni (DBU ) ja yhden tai useampia hydroksyyliryhmiä sisältältävästä molekyylistä (esim. glyseroli) ja happamasta kaasusta (CO2 , SO2) yksinkertaisen menetelmän avulla. [DBU] [ karbonaatti] tai [sulfonaatti] syntetisoitiin kunkin lähtöaineen seoksista kuplittamalla seosta happamalla kaasulla jolloin eksoterminen reaktio tapahtui ja ioninen neste syntyi. Ioniset nesteet voitiin palauttaa takaisin lähtöaineseokseksi kuumentamalla ja/tai kuplittamalla neutraalia kaasua (esim. typpi) seoksen läpi. SIL rakenteet määritettiin ja niiden ominaisuudet kartoitettiin eri menetelmillä, mukaan lukien NMR- ja FTIR -spektroskopia. Ionisen, korkeapoläärisen nesteen syntyminen todennettiin myös viskositeettimittauksilla ja värinmuutoksilla käyttäen hyväksi polariteetti-indikaattoria (Nile red). Myös hajoamislämpötilat määritettiin termogravimetrisellä analyysillä (TGA) ja todettiin että syntetisoitujen yhdisteiden hajoamislämpötila oli välillä 50 ja 200oC . Näiden uusien reversiibeleiden ioninesteiden hajoamisämpötilat olivat korkeammat verrattuna kirjallisuudessa aikaisemmin mainittuihin esimerkkeihin joten niitä voidaan soveltaa useisiin tarkoituksiin. Myös ioninesteitä jotka sisälsivät primäärejä alkoholeja rakennusaineina syntetisoitiin ja hyödynnettiin puun fraktioinnissa. Männyn ja kuusen lisäksi tuoreita koivulastuja onnistuttiin fraktioimaan miedoissa olosuhteissa. Kaikkien syntetisoitujen ioninesteiden todettiin olevan suhteellisen neutraaleja ligniinin liuotuksen suhteen. Vielä, optimaaliset fraktiointiolosuhteet määritettiin ryhmälle reversiibeleitä ioninesteitä ja näiden uudenlaisten ioninesteiden todettiin olevan tehokkaita puun ja muiden lignoselluloosien eri fraktioiden liuotuksessa. Liukenematon osa puulastua joka oli lähinnä selluloosaa fibrilloitui.

Pressure filtration characteristics of enzymatically hydrolyzed biomass suspensions

Enzymatic hydrolysis of lignocellulosic polymers is likely to become one of the key technologies enabling industrial production of liquid biofuels and chemicals from lignocellulosic biomass. Certain types of enzymes are able to hydrolyze cellulose and hemicellulose polymers to shorter units and finally to sugar monomers. These monomeric sugars are environmentally acceptable carbon sources for the production of liquid biofuels, such as bioethanol, and other chemicals, such as organic acids. Liquid biofuels in particular have been shown to contribute to the reduction of net emissions of greenhouse gases. The solid residue of enzymatic hydrolysis is composed mainly of lignin and partially degraded fibers, while the liquid phase contains the produced sugars. It is usually necessary to separate these two phases at some point after the hydrolysis stage. Pressure filtration is an efficient technique for this separation. Solid-liquid separation of biomass suspensions is difficult, because biomass solids are able to retain high amounts of water, which cannot be readily liberated by mechanical separation techniques. Most importantly, the filter cakes formed from biomaterials are compressible, which ultimately means that the separation may not be much improved by increasing the filtration pressure. The use of filter aids can therefore facilitate the filtration significantly. On the other hand, the upstream process conditions have a major influence on the filtration process. This thesis investigates how enzymatic hydrolysis and related process conditions affect the filtration properties of a cardboard suspension. The experimental work consists of pressure filtration and characterization of hydrolysates. The study provides novel information about both issues, as the relationship between enzymatic hydrolysis conditions and subsequent filtration properties has so far not been considered in academic studies. The results of the work reveal that the final degree of hydrolysis is an important factor in the filtration stage. High hydrolysis yield generally increases the average specific cake resistance. Mixing during the hydrolysis stage resulted in undefined changes in the physical properties of the solid residue, causing a high filtration resistance when the mixing intensity was high. Theoretical processing of the mixing data led to an interesting observation: the average specific cake resistance was observed to be linearly proportional to the mixer shear stress. Another finding worth attention is that the size distributions of the solids did not change very dramatically during enzymatic hydrolysis. There was an observable size reduction during the first couple of hours, but after that the size reduction was minimal. Similarly, the size distribution of the suspended solids remained almost constant when the hydrolyzed suspension was subjected to intensive mixing. It was also found that the average specific cake resistance was successfully reduced by the use of filter aids. This reduction depended on the method of how the filter aids were applied. In order to obtain high filtration capacity, it is recommended to use the body feed mode, i.e. to mix the filter aid with the slurry prior to filtration. Regarding the quality of the filtrate, precoat filtration was observed to produce a clear filtrate with negligible suspended solids content, while the body feed filtrates were turbid, irrespective of which type of filter aid was used.

Production of Chemicals from Woody Biomass by Wet Oxidation

The production of chemicals from sawdust by wet oxidation has been investigated. Two different concentrations of sawdust; 54054 mg/l and 32683 mg/l were used in the study. The wet oxidation operating conditions were; 175 deg.C – 225 deg.C, 1MPa Oxygen, and 40 minutes to 120 minutes reaction time. Carboxylic acids were among the chemicals produced in the process. The total yield of carboxylic acids was found to increase with temperature. Also, higher yields of carboxylic acids were observed at a lower sawdust concentration. This was probably due to the high oxygen-biomass ratio at lower sawdust concentration. Higher oxygen availability at low sawdust concentration resulted in increased conversion of the sawdust; hence the higher yields of carboxylic acids. At lower sawdust concentration, a total carboxylic acid yield of 25.59 wt% was attained at 200 deg.C and 40 minutes reaction time. At higher sawdust concentration, a total carboxylic acid yield of 15.57 wt% was attained at 200 deg.C and 40-minutes reaction time. The carboxylic acids identified include formic acid, acetic acid, succinic acid and oxalic acid. The optimum temperature for the production of formic acid was found to be 200 deg.C, while the optimum temperature for the production of acetic acid was found to be 225 deg.C. A temperature of 225 deg.C and relatively short reaction time of 10 minutes was found to be the optimal condition for the production of succinic acid. Formic acid was produced in the highest yield, with an optimal yield of 13.69wt %, when the reaction temperature and time are 200 deg.C and 40 minutes respectively. The yield of formic acid was found to decrease significantly when further increasing the temperature to 225 deg.C. This was presumably due to thermal decomposition of formic acid at relatively higher temperature. However, the yield of acetic acid was found to steadily increase with temperature. This is because acetic is more thermally stable than formic acid. The yield of acetic acid did not decrease after the temperature was increased to 225 deg.C. Optimal yield of acetic acid (7.98wt %) was achieved at; 225 deg.C, and 40 minutes reaction time. Succinic acid was produced only at temperatures of 200 deg.C and 225 deg.C. Optimal yield of succinic acid (5.66wt %) was attained under the following conditions; 32683 mg/l, 225 deg.C, 1MPa O2, and 10-minutes reaction time. Oxalic acid was produced in the lowest yield and, less frequently. The optimal yield of oxalic acid (4.02 wt%) was attained at 175 deg.C and 80-minutes of reaction time The Total Organic Carbon (TOC) is found to be higher when increasing the operating temperature, thus suggesting that more organic compounds are formed at higher temperatures. The identified carboxylic acids could only account for less than 30% of the measured COD content of the various wet oxidation samples. This implies that some other unidentified compounds (reaction products) must have been present. In general, wet oxidation seems to be an effective method for converting lignocellulosic biomass into useful chemicals. Relatively higher temperatures have been found to favor the production of carboxylic acids from sawdust.

Topochemistry of physical and chemical pretreatments of biomass as investigated by FE-SEM, XPS and ToF-SIMS

Surface chemistry is of great importance in plant biomass engineering and applications. The surface chemical composition of biomass which includes lignin, carbohydrates and extractives influences its interactions with chemical agents, such as pulp processing/papermaking chemicals, or enzymes for different purposes. In this thesis, the changes in the surface chemical composition of lignocellulosic biomass after physical modification for the improvement of resulting paper properties and chemical treatment for the enhancement of enzymatic hydrolysis were investigated. Low consistency (LC) refining was used as physical treatment of bleached softwood and hardwood pulp samples, and the surface chemistry of refined samples was investigated. The refined pulp was analysed as whole pulp while the fines-free fibre samples were characterized separately. The fines produced in LCrefining contributed to an enlarged surface specific area as well as the change of surface coverage by lignin and extractives, as investigated by X-ray photoelectron spectroscopy (XPS). The surface coverage by lignin of the whole pulp decreased after refining while the surface coverage by extractives increased both for pine and eucalyptus. In the case of pine, the removal of fines resulted in reduction of the surface coverage by extractives, while the surface coverage by lignin increased on fibre sample (without fines). In the case of eucalyptus, the surface coverage by lignin of fibre samples decreased after the removal of fines. In addition, the surface distribution of carbohydrates, lignin and extractives of pine and eucalyptus samples was determined by Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). LC-refining increased the amounts of pentose, hexose and extractives on the surface of pine samples. ToF-SIMS also gave clear evidence about xylan deposition and reduction of surface lignin distribution on the fibre of eucalyptus. However, the changes in the surface chemical composition during the physical treatment has led to an increase in the adsorption of fluorescent whitening agents (FWAs) on fibres due to a combination of electro-static forces, specific surface area of fibres and hydrophobic interactions. Various physicochemical pretreatments were conducted on wood and non-wood biomass for enhancing enzymatic hydrolysis of polysaccharides, and the surface chemistry of the pretreated and enzymatically hydrolysed samples was investigated by field emission scanning electron microscopy (FE-SEM), XPS and ToF-SIMS. A hydrotrope was used as a relatively novel pretreatment technology both in the case of wood and non-wood biomass. For comparison, ionic liquid and hydrothermal pretreatments were applied on softwood and hardwood as well. Thus, XPS analysis showed that the surface lignin was more efficiently removed by hydrotropic pretreatment compared to ionic liquid or hydrothermal pretreatments. SEM analysis also found that already at room temperature the ionic liquid pretreatments were more effective in swelling the fibres compared with hydrotropic pretreatment at elevated temperatures. The enzymatic hydrolysis yield of hardwood was enhanced due to the decrease in surface coverage of lignin, which was induced by hydrotropic treatment. However, hydrotropic pretreatment was not appropriate for softwood because of the predominance of guaiacyl lignin structure in this material. In addition, the reduction of surface lignin and xylan during pretreatment and subsequent increase in cellulose hydrolysis by enzyme could be observed from ToF-SIMS results. The characterisation of the non-wood biomass (e.g. sugarcane bagasse and common reed) treated by hydrotropic method, alkaline and alkaline hydrogen peroxide pretreatments were carried out by XPS and ToF-SIMS. According to the results, the action for the removal of the surface lignin of non-wood biomass by hydrotropic pretreatment was more significant compared to alkaline and alkaline hydrogen peroxide pretreatments, although a higher total amount of lignin could be removed by alkaline and alkaline hydrogen peroxide pretreatment. Furthermore, xylan could be remarkably more efficiently removed by hydrotropic method. Therefore, the glucan yield achieved from hydrotropic treated sample was higher than that from samples treated with alkaline or alkaline hydrogen peroxide. Through the use of ToF-SIMS, the distribution and localization of lignin and carbohydrates on the surface of ignocelluloses during pretreatment and enzymatic hydrolysis could be detected, and xylan degradation during enzymatic hydrolysis could also be assessed. Thus, based on the results from XPS and ToF-SIMS, the mechanism of the hydrotropic pretreatment in improving the accessibility of enzymes to fibre and further ameliorating of the enzymatic saccharification could be better elucidated.

Comparison of model-based above ground biomass predictions from LiDAR

In order to reduce greenhouse emissions from forest degradation and deforestation the international programme REDD (Reducing Emissions from Deforestation and forest Degradation) was established in 2005 by the United Nations Framework Convention on Climate Change (UNFCCC). This programme is aimed to financially reward to developing countries for any emissions reductions. Under this programm the project of setting up the payment system in Nepal was established. This project is aimed to engage local communities in forest monitoring. The major objective of this thesis is to compare and verify data obtained from di erect sources - remotely sensed data, namely LiDAR and field sample measurements made by two groups of researchers using two regression models - Sparse Bayesian Regression and Bayesian Regression with Orthogonal Variables.