The impact of textile wet colouration on the environment in 2011

Wet textile colouration has the highest environmental impact of all textile processing steps. It consumes water, chemicals and energy and produces liquid, heat and gas waste streams. Liquid effluent streams are often quite toxic to the environment. There are a number of different dyeing processes, normally fibre type specific, and each has a different impact on the environment. This research investigated the energy, chemical and water requirements for the exhaust colouration of cotton, wool, polyester and nylon. The research investigated the liquid waste biological oxygen demand, total organic carbon dissolved solids, suspended solids, pH and colour along with the energy required for drying after colouration. Polyester fibres had the lowest impact on the environment with low water and energy consumption in dyeing, good dye bath exhaustion, the lowest dissolved solids levels in waste water, relatively neutral pH effluent and low energy in drying. The wool and nylon had similar dyebath requirements and outputs however the nylon could be dyed at far lower liquor ratios and hence provided better energy and water use figures. Cotton performed badly in all of the measured parameters.

Toughening of a carbon-fibre composite using electrospun poly(Hydroxyether of Bisphenol A) nanofibrous membranes through inverse phase separation and inter-domain etherification

The interlaminar toughening of a carbon fibre reinforced composite by interleaving a thin layer (~20 microns) of poly(hydroxyether of bisphenol A) (phenoxy) nanofibres was explored in this work. Nanofibres, free of defect and averaging several hundred nanometres, were produced by electrospinning directly onto a pre-impregnated carbon fibre material (Toray G83C) at various concentrations between 0.5 wt % and 2 wt %. During curing at 150 °C, phenoxy diffuses through the epoxy resin to form a semi interpenetrating network with an inverse phase type of morphology where the epoxy became the co-continuous phase with a nodular morphology. This type of morphology improved the fracture toughness in mode I (opening failure) and mode II (in-plane shear failure) by up to 150% and 30%, respectively. Interlaminar shear stress test results showed that the interleaving did not negatively affect the effective in-plane strength of the composites. Furthermore, there was some evidence from DMTA and FT-IR analysis to suggest that inter-domain etherification between the residual epoxide groups with the pendant hydroxyl groups of the phenoxy occurred, also leading to an increase in glass transition temperature (~7.5 °C).

Protein fibre powder and new applications

Protein fibers such as silk and wool have been used as textile fibers for centuries. It is only in recent years that these fibers have been converted into fine powder forms for non-textile applications. This presentation will cover our recent research in protein fiber powders. Ultra-fine powders from different protein fibers have been produced using a combination of media and non media milling techniques. New application examples of these fine powders are discussed. These applications include hybrid fibers combining the advantages of natural and synthetic polymer fibers, tissue engineering composite scaffolds with enhanced biomechanical properties, and metal ion absorption.

On toughening of epoxies and their carbon fibre-reinforced composites

Compared to the neat matrix material, FRC has highly favorable mechanical properties, and their strength-to-weight ratios are superior. In addition, FRCs have potential for use in many applications in dentistry and are expected to gain increasing applications in the future. This book includes both review and research papers in different FRC areas from contributors around the world.

Effects of ultrasonic treatment on wool fibre and fabric properties

The protein structures of wool, treated in fabric form with ultrasonics for different time durations, were analysed by X-ray diffraction (XRD) and Fourier transform infrared (FTIR), in comparison with the wool without ultrasonic treatment. Fabric water absorption and tensile properties were measured in addition to the fibre micro-structure analysis. It is shown that while the ultrasonic treatment had little effect on the fibre crystallinity, some chemical structures in the protein were altered to some extent during the process. Disruption of fibre internal waxy lipids upon ultrasonic treatment provided the fibres with increased water absorption. Protein chains in the macro fibrils were shown to be rearranged to a more regular and less flexible structure, as a result of the ultrasonic treatment. Fabric tensile tests showed an increased tenacity and a reduced extensibility to the ultrasonically treated fabric. Prolonged ultrasonic treatment, however, significantly reduced both fabric tenacity and extensibility.

The long-term performance of cementitious composites reinforced with coir fibre

Effective prediction of the long-term performance of natural fibre-reinforced cementitious materials is vital for their application. In this study, coir fibres of two different average lengths were combined with cementitious materials and chemical agents to form coir fibre-reinforced cementitious composites (CFRCCs). The composites long-term performance was assessed and compared with two different accelerated ageing processes, i.e. a cement-saturated water ageing, and alternate freeze-thaw ageing. The flexural properties were compared with the properties of the reference mortar. Overall, the flexural strength of 400 days naturally aged CFRCC specimens was weaker than that of the reference mortar. The toughness and ductility of the fibre-reinforced specimens, however, improved. The cement-saturated water ageing method gave a precise prediction of the flexural strength development of 400-day-old specimens, and the freeze-thaw ageing method worked very well for the toughness performance estimation of CFRCCs.