Influences of steady and cyclic die rotation on the compression of aluminium

A series of experiments are reported for compression of an aluminum cylinder with monotonic and cyclic die rotation. When the die is monotonically rotated, a higher angular velocity or a lower compression speed of the tool leads to a greater load reduction in comparison of that seen with a stationary die. The test results also show that cyclic die rotation causes a cyclic fluctuation in the load-displacement curve. During the die deceleration phase, the compression load increases until it reaches the level obtained in conventional compression with stationary dies. However, the compression load is observed to reduce to levels lower than those obtained in monotonic rotating compression tests during the die acceleration phase. The frequency of rotating direction change seems to affect the position of load peaks only, not the amplitude of the peaks.

Wearing a sports compression garment on the performance of visuomotor tracking following eccentric exercise : a pilot study

Clinical compression garments have been shown to improve functional control in patients with motor impairments, however, investigation in functional control has not been observed whilst wearing sports compression garments. This pilot study assessed motor control changes in the bicep brachii muscle following a bout of eccentric exercise designed to induce delayed onset muscle soreness for intervals up to 14 days after exercise. Eight male participants performed 35 maximal isokinetic eccentric extensions at 90° s−1. Participants where then randomly divided into one of two groups to perform a one-dimensional elbow flexion/extension visuomotor tracking task; one group wore a sports compression garment during the task, the other acted as control (no garment). The group who wore the compression garment performed the tracking task significantly better immediately post-exercise, and at days 1, 2 and 3 post-exercise (p ≤ 0.05). Non-significant but large and moderate effects sizes (ES), in tracking, were found between the two groups on day 5 (ES = 1.3) and day 7 (ES = 0.7), respectively. Further research is necessary to elucidate these preliminary findings, however, the results suggest that the wearing of sports compression garments post-eccentric exercise has a positive effect on functional motor control.

An illustration of variable precision rough set theory : The gender classification of the European barn swallow (Hirundo rustica)

This paper introduces a new technique in the investigation of object classification and illustrates the potential use of this technique for the analysis of a range of biological data, using avian morphometric data as an example. The nascent variable precision rough sets (VPRS) model is introduced and compared with the decision tree method ID3 (through a ‘leave n out’ approach), using the same dataset of morphometric measures of European barn swallows (Hirundo rustica) and assessing the accuracy of gender classification based on these measures. The results demonstrate that the VPRS model, allied with the use of a modern method of discretization of data, is comparable with the more traditional non-parametric ID3 decision tree method. We show that, particularly in small samples, the VPRS model can improve classification and to a lesser extent prediction aspects over ID3. Furthermore, through the ‘leave n out’ approach, some indication can be produced of the relative importance of the different morphometric measures used in this problem. In this case we suggest that VPRS has advantages over ID3, as it intelligently uses more of the morphometric data available for the data classification, whilst placing less emphasis on variables with low reliability. In biological terms, the results suggest that the gender of swallows can be determined with reasonable accuracy from morphometric data and highlight the most important variables in this process. We suggest that both analysis techniques are potentially useful for the analysis of a range of different types of biological datasets, and that VPRS in particular has potential for application to a range of biological circumstances.

Towards a set of priorities for bird conservation and research in Australia : the perceptions of ornithologists

Australian delegates at the Australasian Ornithological Conference (2007) were surveyed by questionnaire to determine their perceived research and conservation priorities for Australian birds (n = 134). Respondents were honours or postgraduate students (37.4%), academics (26.2%), wildlife managers (6.5%), land managers (6.5%), environmental consultants (5.6%), independent wildlife researchers (5.6%) or had ‘other’ occupations not relevant to birds or their management (12.1%). Respondents rated their priorities on a predetermined set of issues, and were invited to add additional priorities. ‘Conservation of threatened species’ was considered the highest priority, followed by ‘Conservation of birds and biodiversity in general’, ‘Monitoring’, ‘Management’ and ‘Working with communities’. ‘Animal welfare/rights’ was regarded as comparatively less important. Eight of 11 conservation strategies were regarded as of high importance, these included habitat protection and rehabilitation, threat abatement, research, advocacy and education. This study documents the view of the ornithological community with respect to priority issues facing birds and could potentially feed into government and other policies aimed at conserving and understanding Australia’s birds.

Characteristics of the deformed and recrystallised grains obtained after hot plane strain compression of a model Fe-30wt%Ni alloy

The development of physically-based models of microstructural evolution during hot deformation of metallic materials requires knowledge of the grain/subgrain structure and crystallographic texture characteristics over a range of processing conditions. A Fe-30wt%Ni based alloy, retaining a stable austenitic structure at room temperature, was used for modelling the development of austenite microstructure during hot deformation of conventional carbon-manganese steels. A series of plane strain compression tests was carried out at a temperature of 950 °C and strain rates of 10 s-1 and 0.1 s-1 to several strain levels. Evolution of the grain/subgrain structure and crystallographic texture was characterised in detail using quantitative light microscopy and highresolution electron backscatter diffraction. Crystallographic texture characteristics were determined separately for the observed deformed and recrystallised grains. The subgrain geometry and dimensions together with the misorientation vectors across sub-boundaries were quantified in detail across large sample areas and the orientation dependence of these characteristics was determined. Formation mechanisms of the recrystallised grains were established in relation to the deformation microstructure.