Bicyclo[3.2.0]hepta-1,4,6-triene: synthesis, thermal rearrangement, and anion formation

In order to determine the properties of the bicycloheptatrienyl anion (Ia) (predicted to be conjugatively stabilized by Hückel Molecular Orbital Theory) the neutral precursor, bicyclo[3. 2. 0] hepta-1, 4, 6-triene (I) was prepared by the following route.

Reaction of I with potassium-t-butoxide, potassium, or lithium dicyclohexylamide gave anion Ia in very low yield. Reprotonation of I was found to occur solely at the 1 or 5 position to give triene II, isolated as to its dimers.

A study of the acidity of I and of other conjugated hydrocarbons by means of ion cyclotron resonance spectroscopy resulted in determination of the following order of relative acidities:

H₂S ˃ C₅H₆ ˃ CH₃NO₂ ˃ 1, 4- C₅H₈ ˃ I ˃ C₂H₅OH ˃ H₂O; cyclo-C₇H₈ ˃ C₂ H₅OH; фCH₃ ˃ CH₃OH

In addition, limits for the proton affinities of the conjugate bases were determined:

350 kcal/mole ˂ PA(C₅ H₅^-) ˂ 360 kcal/mole

362 kcal/mole ˂ PA(C₅H₇^-, Ia, cyclo-C₇H₇^-) ˂ 377 kcal/mole PA(фCH₂^-) ˂ 385 kcal/mole

Gas phase kinetics of the trans-XVIII to I transformation gave the following activation parameters: E_a = 43.0 kcal/mole, log A = 15.53 and ∆S^ǂ (220°) = 9.6 cu. The results were interpreted as indicating initial 1,2 bond cleavage to give the 1,3-diradical which closed to I. Similar studies on cis-XVIII gave results consistent with a surface component to the reaction (E_a = 22.7 kcal/mole; log A = 9.23, ∆S^ǂ (119°) = -18.9 eu).

The low pressure (0.01 to 1 torr) pyrolysis of trans-XVIII gave in addition to I, fulvenallene (LV), ethynylcyclopentadiene (LVI) and heptafulvalene (LVII). The relative ratios of the C₇H₆ isomers were found to be dependent upon temperature and pressure, higher relative pressure and lower temperatures favoring formation of I. The results were found to be consistent with the intermediacy of vibrationally excited I and subsequent reaction to give LV and LVI.

Study of polymer thermal and mechanical properties using a fiber Bragg grating thermal sensor

A simple and practical method for the study of polymer thermal and mechanical properties using a fiber Bragg grating (FBG) sensor is presented for the first time, in which the FBG is embedded in a typical epoxy polymer. By measuring the sensitivity change of the FBG sensor, changes of the thermal-mechanical properties of the polymer with temperature and pressure can be measured. The experimental results show that this technique is capable of providing continuous in-line monitoring such properties with high sensitivity during transformation between the glassy state and the rubbery state of a polymer within the temperature and pressure range of 20 to 180 C and 0 to 15 MPa. (c) 2007 Society of Photo-Optical Instrumentation Engineers.

Study of polymer thermal and mechanical properties using a fiber Bragg grating thermal sensor

A simple and practical method for the study of polymer thermal and mechanical properties using a fiber Bragg grating (FBG) sensor is presented for the first time, in which the FBG is embedded in a typical epoxy polymer. By measuring the sensitivity change of the FBG sensor, changes of the thermal-mechanical properties of the polymer with temperature and pressure can be measured. The experimental results show that this technique is capable of providing continuous in-line monitoring such properties with high sensitivity during transformation between the glassy state and the rubbery state of a polymer within the temperature and pressure range of 20 to 180 C and 0 to 15 MPa. (c) 2007 Society of Photo-Optical Instrumentation Engineers.