Injeção de vapor e solvente como um método de recuperação avançada em reservatório avançada em reservatórios de óleo pesado

Currently a resource more and more used by the petroleum industry to increase the efficiency of steam flood mechanism is the addition of solvents. The process can be understood as a combination of a thermal method (steam injection) with a miscible method (solvent injection), promoting, thus, the reduction of interfacial tensions and oil viscosity. The use of solvent alone tends to be limited because of its high cost. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a zone of low viscosity between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method, a numerical study of the process was done contemplating the effects of some operational parameters (distance between wells, injection steam rate, kind of solvent and injected solvent volume)on the accumulated production of oil, recovery factor and oil-steam rate. Semisynthetic models were used in this study but reservoir data can be extrapolated for practical applications situations on Potiguar Basin. Simulations were performed in STARS (CMG, 2007.11). It was found that injected solvent volumes increased oil recovery and oil rates. Further the majority of the injected solvent was produced and can be recycled

Diagnóstico da possível influência da atividade petrolífera em sedimentos de fundo da Bacia Piranhas-Açu, região Baixo Açu/RN

It is located in an area of increasing oil exploration, the region of the Lower Açu is at the mercy of a possible pollution generated by this economic activity, which includes various chemical substances harmful to health, such as metals. This thesis aims to, diagnose the areas of River Piranhas-Açu, a region of the Lower Açu, which are polluted by traces factors and more. In this study, it was determined the concentration of the chemica elements Al, CD, Cr, Cu, Fe, Mn, Ni, P, Pb, V and Zn, through the technique of ICP-OES analysis and the size of sediments and their contents organic matter. Were mapped by GPS, 12 points from collections. The interpretations of the results, together associating that allowed pollution to a possible contamination by oil activity. The results showed tha some regions have low concentrations of cadmium, lead, copper, manganese and zinc unable to promote damage to human health. However, there are places where the concentrations of certain metals chromium, iron and zinc are moderately polluted compared to the results with the reference values of literature and others that are highly polluted by iron. However, due to a greater number of wells in production in those locations, those higher concentrations, it can be suggested a possible influence of oi production in some areas with concentrations of chromium and lead are higher than the rest of the points of monitoring. Moreover, it is observed that the highest levels of metals found in sediment of finer texture and more organic matter content

Estudo de reatores eletroquímicos para remoção de Cu2+ , Zn2+, Fenol e BTEX em água produzida

The production of water has become one of the most important wastes in the petroleum industry, specifically in the up stream segment. The treatment of this kind of effluents is complex and normally requires high costs. In this context, the electrochemical treatment emerges as an alternative methodology for treating the wastewaters. It employs electrochemical reactions to increase the capability and efficiency of the traditional chemical treatments for associated produced water. The use of electrochemical reactors can be effective with small changes in traditional treatments, generally not representing a significant additional surface area for new equipments (due to the high cost of square meter on offshore platforms) and also it can use almost the same equipments, in continuous or batch flow, without others high costs investments. Electrochemical treatment causes low environmental impact, because the process uses electrons as reagent and generates small amount of wastes. In this work, it was studied two types of electrochemical reactors: eletroflocculation and eletroflotation, with the aim of removing of Cu2+, Zn2+, phenol and BTEX mixture of produced water. In eletroflocculation, an electrical potential was applied to an aqueous solution containing NaCl. For this, it was used iron electrodes, which promote the dissolution of metal ions, generating Fe2+ and gases which, in appropriate pH, promote also clotting-flocculation reactions, removing Cu2+ and Zn2+. In eletroflotation, a carbon steel cathode and a DSA type anode (Ti/TiO2-RuO2-SnO2) were used in a NaCl solution. It was applied an electrical current, producing strong oxidant agents as Cl2 and HOCl, increasing the degradation rate of BTEX and phenol. Under different flow rates, the Zn2+ was removed by electrodeposition or by ZnOH formation, due the increasing of pH during the reaction. To better understand the electrochemical process, a statistical protocol factor (22) with central point was conducted to analyze the sensitivity of operating parameters on removing Zn2+ by eletroflotation, confirming that the current density affected the process negatively and the flow rate positively. For economical viability of these two electrochemical treatments, the energy consumption was calculated, taking in account the kWh given by ANEEL. The treatment cost obtained were quite attractive in comparison with the current treatments used in Rio Grande do Norte state. In addition, it could still be reduced for the case of using other alternative energy source such as solar, wind or gas generated directly from the Petrochemical Plant or offshore platforms

Cinemática de partículas em fluidos de viscosidade variável com o tempo e sua aplicação na construção de poços de petróleo: avaliação durante paradas operacionais

The new oil reservoirs discoveries in onshore and ultra deep water offshore fields and complex trajectories require the optimization of procedures to reduce the stops operation during the well drilling, especially because the platforms and equipment high cost, and risks which are inherent to the operation. Among the most important aspects stands out the drilling fluids project and their behavior against different situations that may occur during the process. By means of sedimentation experiments, a correlation has been validated to determe the sedimentation particles velocity in variable viscosity fluids over time, applying the correction due to effective viscosity that is a shear rate and time function. The viscosity evolution over time was obtained by carrying out rheologic tests using a fixed shear rate, small enough to not interfere in the fluid gelling process. With the sedimentation particles velocity and the fluid viscosity over time equations an iterative procedure was proposed to determine the particles displacement over time. These equations were implemented in a case study to simulate the cuttings sedimentation generated in the oil well drilling during stops operation, especially in the connections and tripping, allowing the drilling fluid project in order to maintain the cuttings in suspension, avoiding risks, such as stuck pipe and in more drastic conditions, the loss of the well

Caracterização morfológica e molecular de isolados virais obtidos de larvas do complexo Heliothinae.

2016

[Resultados...]

Uma das formas das empresas de pesquisa e transferência de tecnologia estarem alinhadas com as necessidades da cadeia produtiva é através da constante prospecção de demandas, visando subsidiar a elaboração de novos projetos ou estratégias de pesquisa e desenvolvimento (P&D). A prospecção de demandas também permite elaborar melhores estratégias de divulgação dos conhecimentos existentes ou recém gerados pelas empresas de pesquisa públicas e privadas, auxiliando na transferência de tecnologia (TT). Uma das formas de prospectar as demandas de P&D e TT é através de eventos que permitam a participação dos diversos atores que atuam na cadeia produtiva do algodoeiro. Assim, com o objetivo de discutir os principais problemas dos sistemas de produção em que o algodoeiro está inserido, bem como propor alternativas para a superação de eventuais gargalos de natureza tecnológica, em setembro de 2014, em Sinop-MT, promoveu-se o ?Encontro Técnico de Pesquisadores, Consultores e Empresas sobre o manejo da cultura do algodoeiro?, cujos resultados estão sistematizados neste documento.

Potencial biotecnológico de bactérias endofíticas de milho.

Bactérias endofíticas são microrganismos que habitam o interior dos tecidos vegetais e são conhecidas promotoras do crescimento de plantas, favorecendo sua nutrição, pela solubilização de fosfatos, além de produzirem fito-hormônio, enzimas e sideróforos, apresentando potencial para uso como bioinoculantes. O objetivo deste trabalho foi isolar e caracterizar bactérias endofíticas de milho eficientes na solubilização de fosfatos de cálcio e de ferro e na produção de sideróforos, substâncias que atuam na captação de ferro.Para o isolamento das bactérias, foram coletadas plantas de milho no florescimento em área de cerrado, sendo estas posteriormente desinfestadas e maceradas para o isolamento dos endófitos. Foram isoladas 113 bactérias provenientes de raízes (54,9%), folhas (20,4%) e seiva de milho (24,8%). Dessas bactérias, 49 foram caracterizadas geneticamente com base na sequência do 16S rDNA e avaliadas quanto à capacidade de solubilização de fosfatos em meio de cultura líquido contendo fosfato de cálcio e de ferro e produção de sideróforos. Os isolados mais eficientes na solubilização de fosfato de cálcio e fosfato de ferro produziram entre 179,4 a 193,7 mgP. L-1 e 62,7 a 68,7 mg P. L-1, respectivamente. Foi observada uma correlação negativa de -0,58 e -0,48 entre a solubilização de fósforo nos dois fosfatos testados, P-Ca e P-Fe, e os valores de pH, respectivamente, indicando a produção de ácidos orgânicos como o principal mecanismo de solubilização de P. O sideróforo produzido por 69% dos microrganismos avaliados foi do tipo carboxilato. As bactérias endofíticas eficientes na solubilização de P foram identificadas principalmente como pertencentes ao gênero Bacillus e Pantoea. Foi possível concluir que as estirpes bacterianas provenientes do microbioma interno de milho cultivado em solo de cerrado possuem características promissoras de biossolubilização de fosfatos e promoção de crescimento de plantas, sendo possível neste estudo a seleção de seis isolados do gênero Bacillus para futuros testes de inoculação em plantas.