Cationic cyclization of neoprene with a diethylaluminum chloride and organic chloride catalyst system

The cyclization of neoprene was achieved with the aid of a cationic catalyst system based on diethylaluminum chloride (Et2AlCl) and an organic chloride, allyl chloride (CH2=CHCH2Cl) or benzyl chloride (C6H5CH2Cl). The main parameters of the cyclization process were investigated. Elastomers with low intrinsic viscosity, ready solubility and some gelling were obtained. Xylene was a good solvent for the cyclization process, which took place in a very short time (less than or equal to5 min). The products were characterized with IR, H-1-NMR, differential scanning calorimetry, and gel permeation chromatography. The polycyclic structure was determined. The degree of cyctization and the incorporated solvent content were estimated with a H-1-NMR method.

An unusual organic-inorganic chain-like hybrid complex [(CuCl)(2)(o-phen)](infinity) (o-phen=o-phenanthroline)

A novel organic-inorganic hybrid complex [(CuCl)(2) (o-phen)](infinity) 1 (o-phen = o-phenanthroline) has been hydrothermally synthesized and structurally characterized by elemental analyses, XPS spectrum, TG analysis, and single-crystal X-ray diffraction. Compound I crystallizes in the monoclinic system, space group P2(1)/n, a = 3.7285(7) Angstrom, b = 19.603(4) Angstrom, c = 16.757(3) Angstrom, beta = 95.83(3)degrees, V = 1218.4(4) Angstrom(3), Z = 4, lambda(MoKalpha) = 0.71073 Angstrom (R(F) = 0.0643 for 2559 reflections). Data were collected on an R-axis RAPID diffractometer at 293 K in the range of 1.60 < θ < 27.48degrees. The title compound exhibits a one-dimensional chain-like scaffolding constructed by the unusual [Cu3Cl3] hexagon motifs by, sharing opposite edges. Only Cu(1) sites of the [Cu3Cl3] hexagon are coordinated with N donors of o-phen groups. Furthermore, the three-dimensional supermolecular architecture is formed by C-H...Cl hydrogen bonds between o-phen groups and CuCl chains.

Oxadiazole-containing material with intense blue phosphorescence emission for organic light-emitting diodes

2-(2-hydroxyphenyl)-5-phenyl-1, 3, 4-oxadiazole (HOXD), characteristic of excited state intramolecular proton-transfer (ESIPT), was synthesized and found to emit strong blue phosphorescence in the solid state at room temperature and at low temperature (77 K). The photoluminescent spectrum measurement in solution showed that there are two kinds of emission: fluorescence originated from the singlet state and phosphorescence derived from the triplet state in HOXD formed by ESIPT. For the photoluminescent spectrum in the solid state, only phosphorescence emission with the lifetime of 66 mus was observed. Multiple-layer light-emitting diodes with the configuration of ITO/NPB/HOXD/BCP/Alq(3)/Mg:Ag were fabricated using HOXD as emitter and the maximum brightness of 656 cd/m(2) and the luminous efficiency of 0.14 lm/W was obtained.

Blue organic light-emitting devices with an oxadiazole-containing emitting layer exhibiting excited state intramolecular proton transfer

We report a blue organic light-emitting device having an emissive layer of 2-(2-hydroxyphenyl)-5-phenyl-1,3,4-oxadiazole (HOXD), that exhibits excited state intramolecular proton transfer (ESIPT). The device had a luminance efficiency of 0.8 cd/A and a maximum brightness of 870 cd/m(2). Electroluminescence spectra revealed a dominating peak at 450 nm and two additional peaks at 480 and 515 nm with a full width at half maximum of 50 nm. Our studies indicate that some EL may originate from the triplet excitation state of the enol form of HOXD.

Photoluminescence of organic-inorganic hybrid SiO2 xerogels

Organic-inorganic hybrid SiO2 xerogels were prepared by the sol-gel method under various preparation conditions and compositions by using tetraethoxysilane (TEOS), (3-aminopropyl) triethoxysilane (A-PS), (3-glycidoxypropyl) trimethoxysilane (GPS), organic acid (CH3COOH) and inorganic acids (HCl, HNO3, H2SO4) as the main precursors. Luminescence and FT-IR spectra were used to characterize the resulted hybrid SiO2 xerogels. The result of FT-IR spectrum shows that the xerogels are composed of non-crystalline -Si-O-Si- networks containing some organic groups such as -NH, -CH and -OH. Under the excitation of 365 nm, all the hybrid xerogels exhibit strong luminescence in the blue region, but the emission intensity and position depend on the starting precursor compositions to a large extent. Suitable amount of polyethylene glycol (PEG500 and PEG10000) in the hybrid xerogels can enhance the emission intensity. Additionally, the emission intensity of the hybrid xerogels increases with heat treatment temperature in the range of ambient to 200degreesC, and vacuum condition is also able to enhance the emission intensity.

Characterization of organic-inorganic multilayer films by cyclic voltammetry, UV-Vis spectrometry, X-ray photoelectron spectroscopy, small-angle X-ray diffraction and electrochemical impedance spectroscopy

We have employed several techniques, including cyclic voltammetry, UV-Vis spectrometry, small-angle X-ray diffraction, X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy, to characterize the formation processes and interfacial features of ultrathin multilayer films of silicotungstate and a cationic redox polymer on cysteamine-coated Au electrodes self-assembled monolayers. All of these techniques confirm that the multilayer films are built up stepwise as well as uniformly in a layer-by-layer fashion. In particular, the electrochemical impedance spectroscopy is successfully used to monitor the multilayer deposition processes. It has been proved that the electrochemical impedance spectroscopy is a very useful technique in characterization of multilayer films because it provides valuable information about the interfacial impedance features.

Improved efficiency by a graded emissive region in organic light-emitting diodes

Electrical and optical properties of organic light-emitting diodes (OLEDs) with a stepwise graded bipolar transport emissive layer for a better control of charge transport and recombination are presented. The graded bipolar transport layer was formed by co-evaporating a hole-transporting material N,N-'-diphenyl-N,N-'-bis(1,1(')-biphenyl)-4,4(')-diamine (NPB) and an electron-transporting/emissive material tris-(8-hydroxyquinoline) aluminum (Alq(3)) in steps, where each step has a different concentration ratio of NPB to Alq(3). Compared to a conventional heterojunction OLED, electroluminescence efficiency was enhanced by a factor of more than 1.5, whereas the turn-on voltage remained unchanged in the graded structure.