Studies on blackening of canned prawns. Pt. 1. Influence of copper and iron on product blackening

A linear relationship was observed between the copper content and intensity of blackening in commercially canned prawn meat. Average copper and iron contents of non-blackened canned prawn meat were 9.6 and 32.5 ppm on dry weight basis respectively. In the blackened product copper content ranged from 15.8 to 63.9 ppm and iron content between 43.7 and 71.45 ppm depending on the intensity of blackening. But incorporation of copper in the above range to experimental cans produced blackening while iron up to 250 ppm did not impart any blackening under standard conditions of canning.

Influence of size, station time and satiation amount on prey handling time in Anabas testudineus (Bloch)

Satiation amount, satiation time and handling time of Anabas testudineus (Bloch), an air breathing predatory fish was experimentally estimated using guppy (Lebistes reticulatus) as prey. Weight of the fish and satiation time influenced prey handling time. As satiation time is related to the level of hunger, level of hunger was found to influence handling time of prey.

The influence of nitrogen and phosphorus on the growth of a diatom Skeletonema costatum (Greville) Cleve

Nitrogen and phosphorus requirements of a chain-forming diatom, Skeletonema costatum (Greville) Cleve, collected from Yatsushiro Sea, Japan, were investigated in a laboratory culture experiment. Sodium nitrate and sodium glycerophosphate were used as nitrogen and phosphorus sources, respectively. Cultures were grown in modified Provasoli's ASP2NTA medium (Provasoli et al. 1957) at 25±1°C, light intensity 60 µE mˉ² secˉ¹ and photoperiod 12:12-h, L:D cycle. Optimum growth was observed at nitrate concentrations of 3-10 mglˉ¹ and phosphate concentrations of 1.5-15 mglˉ¹. Adequate growth was also found at the nitrate concentration of up to as high as 300 mglˉ¹. Significantly poorer growth was found at lower nitrate (<3.0 mglˉ¹) and higher phosphate (>15 mglˉ¹) concentrations. From the present study, it is concluded that S. costatum can grow well at wide ranges of nitrate concentrations but is sensitive to higher phosphate concentrations.

INFLUENCE OF ATMOSPHERIC HUMIDITY ON THE ABRASIVE WEAR OF METALS.

A pin-on-disc apparatus has been used to obtain continuous simultaneous measurements of the wear and friction (sliding force) behaviour of metals on bonded silicon carbide abrasive paper under conditions of controlled humidity. Iron, mild steel, and copper exhibit qualitatively similar wear behaviour; the wear rate decreases progressively with the number of passes over the same track. In contrast, the wear rate of titanium remains constant. Variation in atmospheric humidity has little effect on the wear rates of copper or titanium, although a slight effect was found in mild steel and iron. Refs.

INFLUENCE OF ATMOSPHERIC COMPOSITION ON THE ABRASIVE WEAR OF TITANIUM AND Ti-6Al-4V.

A pin-on-disc apparatus has been used to investigate the wear and friction (sliding force) behavior of metals on bonded silicon carbide and alumina papers under conditions of controlled atmospheric composition. The wear rates of both commercial purity titanium and the alloy Ti-6%Al-4%V tested in air were found to remain constant with time, in contrast with the behavior of other metals tested under similar conditions, which exhibited a progressive decrease in wear rate with increasing number of passes along the same track. It is proposed that the concentration of interstitial nitrogen and oxygen in the worn metal surface, which largely determines its mechanical properties, strongly influences both the ductility of the abraded material and the force of adhesion between the metal and the abrasive particles. Parallels are drawn between abrasive wear and machining to illustrate the importance of oxygen at the interface between workpiece and tool surfaces.

Influence of some abiotic factors on the acute toxicity of cadmium to Cyprinus carpio

Hardness of water had significant effect on the acute toxicity of cadmium to common carp, Cyprinus carpio. The 96h LC sub(50) and safe application rate increased from 43.17 and 22.77 mg 1 super(-1) in soft water (0.9 mM Ca super(2+) l super(-1)) to 310.48 and 177.66 mg l super(-1), respectively, in very hard water (6.0 mM Ca super(2+) l super(-1)). In medium hard and hard water, 96h LC sub(50) values were 48.39 and 116.45 mg l super(-1). When sediments were included in the medium hard, hard and very hard water treatments, the 96h LC sub(50) were 111.20, 133.71 and 334.47 mg l super(-1), respectively. Among these values, the one for medium hard water with sediment treatment was significantly higher than medium hard water treatment; values for the other two treatments were non-significant when compared with respective water treatments. Sediment was able to reduce the acute toxicity of cadmium mainly due to the complexation of cadmium with dissolved organic carbon (DOC). At the lower hardness level, cadmium complexed with DOC and the acute toxicity was reduced significantly. At higher hardness, most of the DOC sites were occupied by calcium and the acute toxicity of cadmium was not significantly reduced in hard water with sediment and very hard water with sediment experiments in comparison to respective water treatments.