稀土对Al-Mg-Si合金性能影响和稀土作用机理研究

本文研究了稀土对铝镁硅合金性能的影响通过添加稀土改善合金的综合性能,提高合金的成品率,表面光泽性和致密度,讨论了稀土对铝镁硅合金的作用机理,为稀土在铝镁硅合金型材中的推广应用提供了有力的实验依据。

ICP-OES测定浮游有孔虫的Mg/Ca比值及其在SST分析中的应用

海洋是驱动大气环流的主要“引擎”，海表温度（SST）又是揭示海洋环境变化的重要参数。利用有孔虫Mg/Ca比值恢复SST具有较高精密度，是目前恢复SST较成功的方法之一。本论文旨在建立一套有效的有孔虫清洗方法和ICP-OES测试有孔虫Mg/Ca比值的分析方法。 文中分析了53份西菲律宾海区(N18°40.23′，E135°37.11′；水深3225m)表层沉积物中浮游有孔虫Globigerinoides ruber（白色）Mg/Ca比值。结合本研究区的特点，文中使用的清洗方法是有孔虫Mg/Ca比值测试常用的“Mg”清洗方法，主要是由以下步骤构成：①用超纯水和甲醇在超声波水浴中清洗，②显微镜下剔除深色硅酸盐颗粒，③用氧化试剂去除有机质(加入30%H2O2和0.1M NaOH溶液在90℃左右的沸水浴中加热)，④酸洗(250μl 0.001N HNO3 超声波水浴中清洗10S)。清洗干净的样品经超纯硝酸溶解成溶液后，利用电感耦合等离子体发射光谱(ICP-OES)对其进行Mg/Ca比值的分析测试。仪器操作条件如下：辅助气流量（Ar）为0.5L/min（0.5L/min-1.5L/min），雾化器压力为0.2Mpa（0-0.4Mpa），泵速为20rpm（0-125rpm），高频输出功率（RF）为1150W（750W-1500W），火焰高度为15.5mm（8-21mm），通过多次重复测量一组Mg/Ca=3.333mmol/mol的标准溶液，其Mg/Ca短期精密度<0.5%,长期精密度为1%。53份样品之间Mg/Ca比值的RSD为2.7%，利用Lea(2000)建立的太平洋地区浮游有孔虫G. ruber(白色)的Mg/Ca与SST的校正公式:Mg/Ca(mmol/mol) ＝0.30exp[0.089×SST(℃)]，得到本研究区的SST为28℃±0.3℃。

Formation of nano-crystalline corrosion products on Zn-Al alloy coating exposed to seawater

Hot dip Zn-Al alloy coating performs better than hot dip galvanized coating and 55% Al-Zn-Si coating as well with regard to general seawater corrosion protection. A characterization of the corrosion products on Zn-Al alloy coating immersed in dynamic aerated seawater has been performed mainly based on transmission electron microscopy (TEM) for morphological analysis and X-ray diffraction (XRD) technique for crystalline phase identification. The XRD and TEM analyses showed that the corrosion products mainly were typical nanometer Zn4CO3(OH)(6).H2O, Zn-5(OH)(8)Cl-2 and Zn6Al2CO3(OH)(16). 4H(2)O microcrystals. This probably is connected to the co-precipitation of Zn2+ and Al3+ ions caused by adsorption. Zn-Al alloy coating being suffered seawater attacks, AI(OH)(3) gel was first produced on the coating surface. Zn and Al hydroxides would co-precipitate and form double-hydroxide when the concentration of adsorbed Zn2+ ions by the newly produced gel exceeded the critical degree of supersaturation of the interphase nucleation. However, because the growth of the crystals was too low to keep in step with the nucleation, a layer of nano-crystalline corrosion products were produced on the surface of the coating finally. (C) 2001 Elsevier Science Ltd. All rights reserved.

Study on growth factors of intermetallic layer within hot-dipped 25% Al-Zn alloy coating on steel

25%Al-Zn alloy coating performs better than hot dip galvanized coating and 55%Al-Zn-Si coating with regard to general seawater corrosion protection. This study deals with the interfacial intermetallic layer's growth, which affects considerably the corrosion resistance and mechanical properties of 25%Al-Zn alloy coatings, by means of three-factor quadratic regressive orthogonal experiments, The regression equation shows that the intermetallic layer thickness decreases rapidly with increasing content of Si added to the Zn-Al alloy bath, increases with rise in bath temperature and prolonging dip time. The most effective factor that determined the thickness of intermetallic layer was the amount of Si added to Zn-Al alloy bath, while the effect of bath temperature and dip time on the thickness of intermetallic layer were not very obvious.

Effect of alloy elements on the anti-corrosion properties of low alloy steel

Effect of alloy elements on corrosion of low alloy steel was studied under simulated offshore conditions. The results showed that the elements Cu, P, Mo, W, V had evident effect on corrosion resistance in the atmosphere zone; Cu, P, V, Mo in the splash zone and Cr, Al, Mo in the submerged zone.

Nicotinic acid as a nontoxic corrosion inhibitor for hot dipped Zn and Zn-Al alloy coatings on steels in diluted hydrochloric acid

The inhibition effect of nicotinic acid for corrosion of hot dipped Zn and Zn-Al alloy coatings in diluted hydrochloric acid was investigated using quantum chemistry analysis, weight loss test, electrochemical measurement, and scanning electronic microscope (SEM) analysis. Quantum chemistry calculation results showed that nicotinic acid possessed planar structure with a number of active centers, and the populations of the Mulliken charge, the highest occupied molecular orbital (HOMO), and the lowest unoccupied molecular orbital (LUMO) were found mainly focused around oxygen and nitrogen atoms, and the cyclic of the benzene as well. The results of weight loss test and electrochemical measurement indicated that inhibition efficiency (IE%) increased with inhibitor concentration, and the highest inhibition efficiency was up to 96.7%. The corrosion inhibition of these coatings was discussed in terms of blocking the electrode reaction by adsorption of the molecules at the active centers on the electrode surface. It was found that the adsorption of nicotinic acid on coating surface followed Langmuir adsorption isotherm with single molecular layer, and nicotinic acid adsorbed on the coating surface probably by chemisorption. Nicotinic acid, therefore, can act as a good nontoxic corrosion inhibitor for hot dipped Zn and Zn-Al alloy coatings in diluted hydrochloric acid solution. (c) 2007 Elsevier Ltd. All rights reserved.

Alloy elements' effect on anti-corrosion performance of low alloy steels in different sea zones

The corrosion rate of low alloy steel in different sea zones has close correlation with the content of the alloy element. From the field data of steel corrosion rates in atmospheric zone, splash zone and immersion zone, regression analysis was used to study the correlation between the corrosion rate of steels and the amount of added alloy elements. Three regression equations were obtained in different sea zones. Based on the equations, the anti-corrosion performance of the alloy elements can be deduced which can be used to screen out low alloy steel with good anti-corrosion performance. (C) 2007 Elsevier B.V. All rights reserved.