An Hp-Adaptive Hierarchical Formulation for the Boundary Element Method Applied to Elasticity in Two Dimensions

This paper presents an HP-Adaptive Procedure with Hierarchical formulation for the Boundary Element Method in 2-D Elasticity problems. Firstly, H, P and HP formulations are defined. Then, the hierarchical concept, which allows a substantial reduction in the dimension of equation system, is introduced. The error estimator used is based on the residual computation over each node inside an element. Finally, the HP strategy is defined and applied to two examples.

Substitution-Newton-Raphson method applied to the modeling of a vapour compression refrigeration system using different representations of the thermodynamic properties of R-134a

This paper gives a detailed presentation of the Substitution-Newton-Raphson method, suitable for large sparse non-linear systems. It combines the Successive Substitution method and the Newton-Raphson method in such way as to take the best advantages of both, keeping the convergence features of the Newton-Raphson with the low requirements of memory and time of the Successive Substitution schemes. The large system is solved employing few effective variables, using the greatest possible part of the model equations in substitution fashion to fix the remaining variables, but maintaining the convergence characteristics of the Newton-Raphson. The methodology is exemplified through a simple algebraic system, and applied to a simple thermodynamic, mechanical and heat transfer modeling of a single-stage vapor compression refrigeration system. Three distinct approaches for reproducing the thermodynamic properties of the refrigerant R-134a are compared: the linear interpolation from tabulated data, the use of polynomial fitted curves and the use of functions derived from the Helmholtz free energy.

On non-ideal and non-linear portal frame dynamics analysis using bogoliubov averaging method

We apply the Bogoliubov Averaging Method to the study of the vibrations of an elastic foundation, forced by a Non-ideal energy source. The considered model consists of a portal plane frame with quadratic nonlinearities, with internal resonance 1:2, supporting a direct current motor with limited power. The non-ideal excitation is in primary resonance in the order of one-half with the second mode frequency. The results of the averaging method, plotted in time evolution curve and phase diagrams are compared to those obtained by numerically integrating of the original differential equations. The presence of the saturation phenomenon is verified by analytical procedures.

Adaptation of TRIZ Method for Problem Solving in Process Engineering

TRIZ is one of the well-known tools, based on analytical methods for creative problem solving. This thesis suggests adapted version of contradiction matrix, a powerful tool of TRIZ and few principles based on concept of original TRIZ. It is believed that the proposed version would aid in problem solving, especially those encountered in chemical process industries with unit operations. In addition, this thesis would help fresh process engineers to recognize importance of various available methods for creative problem solving and learn TRIZ method of creative problem solving. This thesis work mainly provides idea on how to modify TRIZ based method according to ones requirements to fit in particular niche area and solve problems efficiently in creative way. Here in this case, the contradiction matrix developed is based on review of common problems encountered in chemical process industry, particularly in unit operations and resolutions are based on approaches used in past to handle those issues.

Combining Good Practices : Method to study Introductory Physics in Engineering Education

Julkaisumaa: 056 BE BEL Belgia

The effect of shielding gas feeding method in laser welding of steel

Gas shielding plays an important role in laser welding phenomena. This is because it does not only provide shielding against oxidization but it has an effect in beam absorption and thus welds penetration. The goal of this thesis is to study and compare the effects of different shielding gas feeding methods in laser welding of steel. Research method is a literature survey. It is found that the inclination angle and the arrangement of the gas feeding nozzles affect the phenomena significantly. It is suggested that by designing shielding gas feeding case specifically better welding results can be obtained.

Young Registered Nurses’ Intent to Leave the Profession in Finland - A Mixed-Method Study

The purpose of this study was to examine and expand understanding concerning young Finnish registered nurses (RN) with an intention to leave the profession and the related variables, specifically when that intention has emerged before the age of 30. The overall goal of the study was to develop a conceptual model in relation to young RNs’ intention to leave the profession. Suggestions for policymakers, nurse leaders and nurse managers are presented for how to retain more young RNs in the nursing workforce. Suggestions for future nursing research are also provided. Phase I consists of two sequential integrative literature reviews of 75 empirical articles concerning nurses’ intention to leave the profession. In phase II, data had been collected as part of the Nurses’ Early Exit (NEXT) study, using the BQ-12 structured postal questionnaire. A total of 147 young RNs participated in the study. The data were analysed with statistical methods. In phase III, firstly, an in-depth interpretive case study was conducted in order to understand how young RNs explain and make sense of their intention to leave the profession. The data in this study consisted of longitudinal career stories by three young RNs. The data was analysed by using narrative holistic-content and thematic methods. Secondly, a total of 15 young RNs were interviewed in order to explore in-depth their experiences concerning organizational turnover and their intent to leave the profession. The data was analysed using conventional content analysis. Based on earlier research, empirical research on the young RNs intention to leave the profession is scarce. Nurses’ intention to leave the profession has mainly been studied with quantitative descriptive studies, conducted with survey questionnaires. Furthermore, the quality of previous studies varies considerably. Moreover, nurses’ intention to leave the profession seems to be driven by a number of variables. According to the survey study, 26% of young RNs had often considered giving up nursing completely and starting a different kind of job during the course of the previous year. Many different variables were associated with an intention to leave the profession (e.g. personal burnout, job dissatisfaction). According to the in-depth inquiries, poor nursing practice environments and a nursing career as a ‘second-best’ or serendipitous career choice were themes associated with young RNs’ intention to leave the profession. In summary, young RNs intention to leave the profession is a complex phenomenon with multiple associated variables. These findings suggest that policymakers, nurse leaders and nurse managers should enable improvements in nursing practice environments in order to retain more young RNs. These improvements can include, for example, adequate staffing levels, balanced nursing workloads, measures to reduce work-related stress as well as possibilities for advancement and development. Young RNs’ requirements to provide high-quality and ethical nursing care must be recognized in society and health-care organizations. Moreover, sufficient mentoring and orientation programmes should be provided for all graduate RNs. Future research is needed into whether the motive for choosing a nursing career affects the length of the tenure in the profession. Both quantitative and in-depth research is needed for the comprehensive development of nursing-turnover research.

Process modeling method for electric accessories manufacturing enterprise

The theoretical research of the study focused to business process management and business process modeling, the goal was to found a new business process modeling method for electrical accessories manufacturing enterprise. The focus was to find few options for business process modeling methods where company could have chosen the best one for its needs The study was carried out as a qualitative research with an action study and a case study as the most important ways collect data. In the empirical part of the study examples of company’s processes modeled with the new modeling method and process modeling process are presented. The new way of modeling processes improves especially visual presentation of the processes and improves the understanding how employees should work in the organizational interfaces of the process and in the interfaces between different processes. The results of the study is a new unified way to model company’s processes, which makes it easier to understand and create the process models. This improved readability makes it possible to reduce the costs that were created from the unclear old process models.

In-House Validation of Capillary Electrophoresis Method

Capillary electrophoresis method designed originally for the analysis of monosaccharides was validated using reference solutions of polydatin. The validation was conducted by studying and determining the concentration levels of LOD and LOQ and the range of linearity and by determining levels of uncertainty in respect to repeatability and reproducibility. The reliability of the gained results is also discussed. A guide with recommendations considering the validation and overall design of analysis sequences with CE is also produced as a result of this study.